Review Index:

Abit KA7 KX133 Motherboard Review

Author: Ryan Shrout
Subject: Motherboards
Manufacturer: Abit


This content was originally featured on and has been converted to PC Perspective's website. Some color changes and flaws may appear.

have decided to use the ‘ka7_42’ evaluation ROM I obtained from href="" title="Click here to go there.">BXBoards.
If you are not into betas, then I suggest the ‘ href=""
title="Download this revision.">KA7RK’ revision, which is Abit’s latest
official BIOS release. Abit uses Award BIOS, with most all of their other
boards, I personally prefer AMI, but Award’s SoftMenu III featured with this
board is something AMI cannot touch. Here are some suggested settings of my own
with a word or two explaining them:


Speed Error Hold –
Disabled - default, in order to get to this setting you need to change the CPU
Operating Speed to ‘User Define’; this setting will

Fast CPU Command
Decode – Fast - this setting will increse performance all around, Normal is
default and meant for greater stability.

CPU Pull Up Strength –
Auto – effects signal strength from the north bridge chipset to the CPU, this
has a default of three, minor performance gain in letting the motherboard
decide, as it also decides stability.

CPU Drive Strength –
Auto – similar to the Pull Up setting; this has a default of two.

DRAM Clock –
HCLK+PCICLK – If you have PC133 memory, this is the way to take advantage of
it; PC100 is also supported, set it to HCLK. It seems PC66 memory is supported
with the HCLK-PCICLK setting, I am not sure though.

Autodetect DRAM/PCI
Clk – Enabled – default, this is new to the BIOS setup and I believe it has to
do with the memory to PCI ratio (3:1, 4:1). Stability problems did arise when

Spread Spectrum
Modulated – Disabled – default, this setting has to to with Electro-Magnetic
Compatibility, no performance gain or instability problems are seen when

CPU L2 ECC Checking –
Enabled – default – despite that people say disabling this will increase
performance, they do not understand ECC. Enabling ECC does not in any way
hinder performance and should definitely be enabled when overclocking to
overcome instability problems.

DRAM Timing – Turbo –
Although it sounds kind of non-technical, turbo is best of all the settings
provided. Large increases in performance were seen over the default of 10ns

DRAM Bank Interleave –
4-way – this setting might not work on all types of memory from what I hear, I
had no problems and saw better performance and greater stability. So go buy the
more expensive memory, it is the best way to tweak your rig.

Delay DRAM Read Latch
– Auto – I experienced instability problems when changing this. As lame as it
may seem, auto is sometimes the way to go, but I can hear what you are saying,
‘I want to optimize this motherboard myself’’, because Auto often seems
like the easy way out.

SDRAM Cycle Length – 2
or 3 – OK, my system runs terrible at two, it ran fine at two with my Asus K7M.
This setting you are going to have to do alone, I run at three.

MD Driving Strength –
Hi – If your memory loading is heavy, set to Hi. If light, set to Lo.

P2C/C2P Concurrency –
Enabled – This enables simultaneous data transfer between the CPU to the PCI
bus and back, increasing performance, disable if problems arise.

Fast R-W Turn Around –
Enabled – Allows the AGP bus to talk directly to the CPU, therefore bypassing
memory and increasing performance. Again, disable to troubleshoot stability

System BIOS Cachable –
Disabled – this loads BIOS into cache allowing faster execution in the BIOS setup
program, no performance gain seen, leave at default.

Video RAM Cacheable –
Disabled – allows video memory to be cached and is not necessary with AGP video

AGP-4X Mode – Enabled
– simple enough, if you have an AGP-4X card, set to enable. If problems arise,
load the latest drivers and perhaps flash your video card’s firmware with the
latest version.

Fast Write Supported –
Supported – Having this setting within the BIOS setup program allows users of
GeForce (or other Fast Write cards) video cards to disable it without a fuss.
Of course, Supported does make for better frame rates.

K7 CLK_CTL – Optimal –
default, I have no idea what this does, nobody really knows yet, makes you
wonder though.

AGP Driving Control –
Auto – This allows manual setting of the AGP Driving Force, values are set
under AGP Driving Value.

PCI Dynamic Bursting –
Enabled – To avoid incompatabilities set to enabled, no gain in stability or
performance when disabled.

PCI Master 0 WS Write
– Enabled – default, writes to the PCI bus are executed immediately, when
disabled the PCI bus waits one state and then executes. Use this for
compatibility with very old PCI devices (PCI 2.0).

PCI Delay Transaction
– Enabled – default, mixed results on this setting, this setting is to support
PCI delay transaction to enhance compatibilty with newer features on the PCI

AGP Master 1 WS Write
– Disabled – default, setting this to enabled will set single delay before
writing to the AGP bus. Enable if your older AGP card is causing problems.

AGP Master 1 WS Read –
Disabled – default, same as above, except for read. These two settings should
be hand-in-hand.

No comments posted yet.

Post new comment

The content of this field is kept private and will not be shown publicly.
  • Lines and paragraphs break automatically.
  • Allowed HTML tags: <a> <em> <strong> <cite> <code> <ul> <ol> <li> <dl> <dt> <dd> <blockquote><p><br>
  • Web page addresses and e-mail addresses turn into links automatically.

More information about formatting options

By submitting this form, you accept the Mollom privacy policy.