Review Index:

Corsair AX1200i Digital ATX 1200W Power Supply Review

Author: Lee Garbutt
Manufacturer: Corsair

Efficiency, Differential Temperature and Noise


The overall efficiency of a power supply is very important, especially when the power supply is designed to deliver over 1,000W DC output.  The less waste heat generated the better!  Efficiency is defined by the power output divided by the power input and is usually expressed as a percentage.  If a PSU were a 100% efficient (which none are) 1,000 watts of AC power going in would result in 1,000 watts of DC power coming out (with no waste heat to dissipate).  In the real world there are always inefficiencies and power is lost in the form of heat during the conversion process.

View Full Size

The latest revisions to the ATX12V Power Supply Design Guide V 2.2 have continued to increase the efficiency recommendations for PC switching mode power supplies and now lists both required and recommended minimum efficiencies.

View Full Size

I measured the AC power input to the Corsair AX1200i Digital PSU with the Extech power analyzer while the total DC load was found by adding all the individual +3.3V, +5V, +12V, -12V and +5VSB loads together. 

View Full Size

View Full Size

The overall efficiency of the AX1200i Digital power supply is very good and it should be to be certified 80 Plus Platinum.  During our testing the PSU had no problems meeting the 80 Plus Platinum criteria while operating on 240 VAC and at real world temperatures (up to 40°C).  However, when the PSU was operating on 115 VAC, it struggled a little.  Rounding the numbers up to the nearest whole decimal (which is well within the range of error) fixes the problem. Note that the 80 Plus test criteria only calls for 25°C operating temperature, which is unrealistic in the real world, and makes it easier for a PSU to be certified. 

80 Plus Program

View Full Size

      Note 1: Power Factor ≥0.90 (50% to 100% Load)
      Note 2: Tests conducted at room temperature (25°C)

Differential Temperature and Noise Levels

To simulate real world operation, some of the warm exhaust air from the PSU under test is recirculated back to the intake through a passive air duct, which allows the PSU air inlet temperature to increase with load, just like it would in a real PC. 

The differential temperature across the power supply was calculated by subtracting the internal case air temperature (T in) from the temperature of the warm exhaust air flowing out the back of the power supply (T out). 

Thermocouples were placed at the air inlet and exhaust outlet. The ambient room air temperature was 23ºC (74ºF) +/- 0.5ºC during testing.

T out = temperature of air exhausting from power supply
T in = temperature of air entering power supply
Delta T = T out - T in

Sound pressure level readings were taken 3’ away from the rear of the case in an otherwise quiet room.  The ambient noise level was ~28 dBA. 

View Full Size

*Fan not running 

Below ~300W output and with a relatively cool ambient inlet air temperature, the Corsair AX1200i Digital PSU is silent as the fan does not even turn on.  Above 30% load the fan starts to spin and gradually speeds up as the load continues to increase. At 50% load the fan is still relatively quiet. Having high efficiency helps with less waste heat to dissipate. Alternate fan speed profiles are available through the Corsair Link software if you want to customize the fan speed settings.

Note: I was not able to take SPL readings at the higher loads due to all the programmable DC load cooling fans running in the background.   

View Full Size

(Corsair AX1200i Fan Noise - Courtesy of Corsair)

August 30, 2012 | 11:59 AM - Posted by KngtRider

Lee and or PCPER I am a bit confused about the PSU test bench as described in this article. 'Up to 2000W' but also mention real-world test.

Which tests are you using the PC-based load for and which tests are you using simulated loads for ?

Or are you using both?

Many of the top review sites are using the imported ATX tester or home brew resistor grids which is not a 'real world test' (but a simulated one) and I am interested as to how you are pulling off a real world PSU test

Additionally, testing in open air versus mounted in a warm PC chassis, typically pushed against a wall or under a desk.


August 30, 2012 | 08:21 PM - Posted by Lee Garbutt

The PCPerspective PSU test bench uses a combination of six Progammable DC loads and up to three different banks of precision load resistors to create the various loads (up to 2,000W max). The real-world testing is stated because we mount each PSU in a modified case and recirculate some of the warm exhaust air back to the inlet to "simulate" real-world operating conditions.  The loads are not real-world (actually much more precise and programmable) but the test environment is, temps gradually increase as the load increases just like in a real PC - the best of both worlds.

March 4, 2016 | 10:41 PM - Posted by Anonymous (not verified)

Hi I'm Carlos , I have a Corsair AX1200.

March 4, 2016 | 10:42 PM - Posted by Anonymous (not verified)


Post new comment

The content of this field is kept private and will not be shown publicly.
  • Lines and paragraphs break automatically.
  • Allowed HTML tags: <a> <em> <strong> <cite> <code> <ul> <ol> <li> <dl> <dt> <dd> <blockquote><p><br>
  • Web page addresses and e-mail addresses turn into links automatically.

More information about formatting options

By submitting this form, you accept the Mollom privacy policy.