All | Editorial | General Tech | Graphics Cards | Networking | Motherboards | Cases and Cooling | Processors | Chipsets | Memory | Displays | Systems | Storage | Mobile | Shows and Expos
Subject: Memory | February 6, 2015 - 08:40 PM | Tim Verry
Tagged: overclocking, kingston hyper x, kingston, ddr4, ces 20156, CES
Overclocker "Toppc" from MSI was able to crank a single stick of DDR4 memory to a world record 4,351 MHz at the International CES 2015 competition. Toppc paired the Kingston Predator DDR4 DIMM with an Intel Haswell-E Core i7-5960X processor and a MSI X99S Xpower AC motherboard. After disabling all but one CPU core and adding in copious amounts of liquid nitrogen, the 4GB memory module was overclocked to 4,351 MHz which was measured using CPU-Z (CPU-Z Validation) and verified with an oscilloscope (shown in the embedded video below).
This overclock is quite impressive even if it is not something you can run at home especially for DDR4 which is designed to use less power than DDR3. Out of the box the DIMMs are rated at up to 3,333 MHz which means they achieved an impressive 30.54% overclock (an increase of 1,018 MHz).
This kind of overclock will only result in marginal performance gains (at best) in everyday applications, but is still cool to see. Also, it surely won't hurt benchmark runs!
Subject: Memory | January 13, 2015 - 01:31 PM | Jeremy Hellstrom
Tagged: ddr4, ddr4-2800, corsair, Corsair Vengeance LPX, X99
With the release of the X99 chipset came the introduction of DDR4, which is not seeing the same uptake as DDR3 did at launch, though it is still selling well. Part of this may be the pricing, DDR3 was expensive when it first launched but even stalwart early adopters may balk at the $340 asking price for the Corsair Vengeance LPX 16GB 2800MHz. The other main reason for the mild reception is the minimal performance gains which DDR4 offers, you can see a slight difference in synthetic benchmarks but when it comes to gameplay the performance increase is minuscule for the price you pay. If you do have an X99 board then this kit is a good choice for you, not only can you often find similar kits on sale for significantly less that $300, Overclockers Club overclocked these DIMMs to 3200MHz at timings of 16-16-16-30. Check out their review here.
"Packed full of promise, the latest modules in the Vengeance series of Corsair's DDR4 memory lineup deliver excellent performance when tweaked to get the tightest timings. Out of the box they come with 16-18-18-36 primary timings using just 1.2v to run the modules. By tweaking the applied voltage a little bit you can get the timings much tighter at the rated speed and even when running at my max overclock of 3200MHz. At this speed I was able to run the timings at 15-15-15-28 2T using over 1.4v applied to the modules."
Here are some more Memory articles from around the web:
- Crucial DDR4-2133 32GB Memory Kit Review @ Hardware Canucks
- Corsair Vengeance LPX DDR4 2666MHZ 16GB Quad Channel Memory Kit @ Bjorn3D
- Corsair DDR4 16GB Vengeance LPX 2800C16 Memory Kit Review @ Madshrimps
- Avexir Core Series 1600MHz CL9 memories with orange LEDs @ HardwareOverclock
Subject: Memory | October 20, 2014 - 02:12 PM | Jeremy Hellstrom
Tagged: Vengeance LPX, corsair, Ripjaws 4, G.Skill, hyperx predator, kingston, ddr4, DDR4-3000
With the new DDR4 standard comes new speeds and of course updated branding from the major memory resellers. As it is brand new there is a possibility that some memory is better than others at this point, which is why Kitguru assembled three different kits to test. Corsair's Vengeance LPX, G.Skill's Ripjaws 4 and Kingston's HyperX Predator all have very similar specifications on paper though each has a distinctive look. Read on to find out if there is a brand that you should be looking for right now, or if it is price and availability which should drive your purchasing decision.
"One of the key technological advancements that the Haswell-E processors and Intel’s latest High-End Desktop (HEDT) platform iteration have brought into the consumer limelight is DDR4. We compare three 16GB quad-channel memory kits from Corsair, G.Skill, and Kingston, all running at 3000MHz. Is there a specific set of ‘go-to’ memory at this early point in the DDR4 life-cycle?"
Here are some more Memory articles from around the web:
- G.SKILL Ripjaws 4 16 GB 3000 MHz Kit (4x 4GB DDR4) @ techPowerUp
- Crucial Ballistix Sport DDR4 @ HardwareHeaven
- Corsair Vengeance LPX 16GB 2800MHz Quad Channel DDR4 Memory Kit @ eTeknix
- Kingston HyperX Predator 16GB 3000MHz Quad Channel DDR4 @ eTeknix
- Crucial Ballistix Sport XT 32GB 1866MHz Quad Channel DDR3 @ eTeknix
Subject: Memory | September 15, 2014 - 05:17 PM | Jeremy Hellstrom
Tagged: kingston, hyperx predator, DDR4-3000, ddr4
Ah DDR3, it has been a long and fruitful partnership and it is good to know you won't be going anywhere soon but you now have a younger sibling that is attracting a lot of attention. DDR4 has arrived, with a base clock of 2133MHz and many kits with higher frequencies also appearing for sale. The ~$350, 16GB Kingston HyperX Predator kit which Legit Reviews just reviewed comes with two XPM profiles, one @ 3000MHz with timings of 15-16-16-39 and one @ 2666MHz at 14-14-14-36 and they also tested the kit @ 2133MHz with the previous timings. As you read through the review you will notice that the synthetic benchmarks show much more drastic differences than do the gameplay tests, similar to what was seen with DDR3. As with the previous generation it looks as though tighter timings trump frequency in the majority of cases.
"Now that the Intel X99 chipset has been released along with the Intel Haswell-E processor series we have entered the era of DDR4 memory. There are many DDR4 memory kits on the market and right now you can find 16GB to 64GB kits of DDR4 memory ranging in speeds of 2133MHz to 3333MHz. The sheer number of kits on the market for the platform launch is rather impressive and luckily there are a good number of Intel X99 based motherboards that are ready to support DDR4 memory frequencies well beyond the JEDEC standard clock frequency of 2133MHz."
Here are some more Memory articles from around the web:
- G.SKILL Ripjaws 4 16GB DDR4 3000 MHz Memory Kit Review @ Legit Reviews
- G.Skill 16GB 2400MHz RipJaws 4 Quad Channel DDR4 @ eTeknix
- Crucial 32GB 2133MHz Quad Channel DDR4 @ eTeknix
- DDR4 Roundup featuring Corsair, Crucial and G.Skill @ HardwareHeaven
- G.Skill Ares 8GB 2400MHz Dual Channel DDR3 @ eTeknix
Subject: Storage, Shows and Expos | September 10, 2014 - 03:34 PM | Allyn Malventano
Tagged: TSV, Through Silicon Via, memory, idf 2014, idf
If you're a general computer user, you might have never heard the term "Through Silicon Via". If you geek out on photos of chip dies and wafers, and how chips are assembled and packaged, you might have heard about it. Regardless of your current knowledge of TSV, it's about to be a thing that impacts all of you in the near future.
Let's go into a bit of background first. We're going to talk about how chips are packaged. Micron has an excellent video on the process here:
The part we are going to focus on appears at 1:31 in the above video:
This is how chip dies are currently connected to the outside world. The dies are stacked (four high in the above pic) and a machine has to individually wire them to a substrate, which in turn communicates with the rest of the system. As you might imagine, things get more complex with this process as you stack more and more dies on top of each other:
16 layer die stack, pic courtesy NovaChips
...so we have these microchips with extremely small features, but to connect them we are limited to a relatively bulky process (called package-on-package). Stacking these flat planes of storage is a tricky thing to do, and one would naturally want to limit how many of those wires you need to connect. The catch is that those wires also equate to available throughput from the device (i.e. one wire per bit of a data bus). So, just how can we improve this method and increase data bus widths, throughput, etc?
Before I answer that, let me lead up to it by showing how flash memory has just taken a leap in performance. Samsung has recently made the jump to VNAND:
By stacking flash memory cells vertically within a die, Samsung was able to make many advances in flash memory, simply because they had more room within each die. Because of the complexity of the process, they also had to revert back to an older (larger) feature size. That compromise meant that the capacity of each die is similar to current 2D NAND tech, but the bonus is speed, longevity, and power reduction advantages by using this new process.
I showed you the VNAND example because it bears a striking resemblance to what is now happening in the area of die stacking and packaging. Imagine if you could stack dies by punching holes straight through them and making the connections directly through the bottom of each die. As it turns out, that's actually a thing:
Subject: Motherboards, Processors, Chipsets, Memory, Storage | September 5, 2014 - 01:21 PM | Ryan Shrout
Tagged: X99-Deluxe, SSD 730, Intel, Haswell-E, ddr4, asus, 5960X
Okay, I'll be the first to admit that I didn't know what I was getting into. When a couple of packages showed up at our office from Intel with claims that they wanted to showcase the new Haswell-E platform...I was confused. The setup was simple: turn on cameras and watch what happens.
So out of the box comes...a containment chamber. A carefully crafted, wood+paint concoction that includes lights, beeps, motors and platforms.
Want to see how Intel promotes the Core i7-5960X and X99 platform? Check out this video below.
Our reviews of products included in this video:
Subject: Motherboards, Memory | August 29, 2014 - 12:25 PM | Jeremy Hellstrom
Tagged: X99, ddr4, corsair, asus, Dominator Platinum, X99-Deluxe, Rampage V Extreme
PAX Prime, Seattle —August 29, 2014 — Corsair, a worldwide leader in high-performance PC components and ASUS a worldwide leader in motherboards, today announced the availability of the Corsair Dominator Platinum DDR4 memory kits in 3300MHz, 3200MHz and 3000MHz speeds – the world’s fastest production memory kits. Corsair developed the new high-speed DDR4 memory in close collaboration with ASUS, tuning and validating the memory timings to take advantage of the optimized DRAM layout and UEFI firmware of ASUS’s new X99 motherboards. The new Dominator DDR4 memory kits, when paired with the ASUS X99 Deluxe and Rampage V Extreme motherboards, creates some of the fastest, most stable enthusiast PC platforms available for the new Intel Core i7 processors (codenamed Haswell-E).
“Our rigorous validation with ASUS has enabled us to make Dominator Platinum 3300MHz the fastest desktop DDR4 memory available at launch,” said Thi La, Chief Operating Officer at Corsair. “Our OC team and engineers are excited to see such performance headroom the new Intel platform and are looking forward to releasing even faster kits in the near future.”
“It is always exciting when two companies renowned for being at the forefront of innovation and pushing performance boundaries work together to create new products for end-users. The combination of ASUS X99 motherboards with Corsair Dominator Platinum ushers in a new era of memory performance and stability for enthusiasts,” Joe Hsieh, ASUS Corporate Vice President and General Manager of the Motherboard and Desktop System Business Unit.
Corsair Dominator Platinum DDR Memory
Dominator Platinum memory kits have a striking industrial design for good looks, patented DHX technology for cooler operation, user-swappable colored “light pipes” for customizable downwash lighting, and Corsair Link compatibility for real-time temperature monitoring. Dominator Platinum memory is built with hand-screened ICs, undergoes rigorous performance testing, and incorporates state-of-the-art cooling for reliable performance in demanding environments.
The ASUS X99-Deluxe and Rampage V Extreme
The ASUS X99-Deluxe and Rampage V Extreme feature an enhanced CPU socket and DRAM trace layout to improve signal integrity, providing increased overclocking headroom and stability over reference designs. This is coupled with a highly customized and refined UEFI firmware that allows easy setup and tweaking – perfect for getting the most from Corsair Dominator Platinum memory.
Availability and Warranty
The DDR4 memory kits are available in Corsair’s Vengeance LPX and Dominator Platinum lines. The memory kits are available immediately via Corsair’s worldwide network of authorized distributors and resellers and are backed by a lifetime warranty.
The ASUS X99-Deluxe and Rampage V Extreme motherboards are available now at ASUS authorized distributors and resellers worldwide. Both motherboards are covered by a three year warranty with advanced replacement in the first year.
Subject: Editorial, General Tech, Memory | August 20, 2014 - 04:08 PM | Jeremy Hellstrom
Tagged: Haswell-E, G.Skill, ddr4-2800, ddr4-2666, ddr4-2400, ddr4-2133, ddr4, crucial, corsair
DDR4 is starting to arrive at NewEgg and some kits are actually in stock for those who want to be the first on their block to have these new DIMMs and can remortgage their home. The price of Haswell-E CPUs and motherboards is as of yet unknown but looking over the past few years of Intel's new processors you can assume the flagship processor will be around $999.99 with the feature rich motherboards starting around $200 and quickly raising from there.
At the 16GB mark you have more choices with Corsair joining in and a range of speeds that go up to DDR4-2800 as well as your choice of a pair of 8GB DIMMs or four 4GB DIMMs. Corsair was kind enough to list the timings, the DDR4-2666 @ 15-17-17-35 and the DDR4-2800 @ 16-18-18-36 though you will certainly pay a price for the RAM with the highest frequencies.
For those on a budget it would seem like waiting is your best choice, especially as Amazon is offering a limited selection of the new kits, as there is only a single 8GB kit from Crucial although you can buy two of the single DIMMs without heatspreaders for $110.
Intel product releases are always dearly priced, the introduction of a new generation of RAM is both exciting and daunting. You will see power reductions, base frequencies that were uncommon in DDR3 and very likely an increase in the ability to overclock these DIMMs but it is going to cost you. If Haswell-E is in your sights you should start planning on how to afford replacing your CPU, motherboard and RAM at the same time as this is no refresh this is a whole new product line.
Subject: Memory | August 15, 2014 - 12:24 PM | Jeremy Hellstrom
Tagged: ddr4, corsair, Vengeance LPX, Dominator Platinum
FREMONT, California — August 14, 2014 — Corsair, a leader in high-performance PC hardware, today announced the availability of Corsair Vengeance LPX and Dominator Platinum lines of high-speed DDR4 computer memory. This new generation of memory ushers in a new age of ultrafast computing with optimizations such as increased DRAM bandwidth, higher bus frequencies, lower power usage, and higher reliability.
Corsair Vengeance LPX and Dominator Platinum DDR4 memory kits are validated with motherboard partners (ASUS, ASRock, EVGA, Gigabyte, and MSI) and use the new XMP 2.0 profile to deliver easy, reliable overclocking performance with the upcoming next-generation Intel® X99 platforms and Intel® Core™ i7 processors (codenamed Haswell-E). The Vengeance LPX and Dominator Platinum memory kits are supplied with a limited lifetime warranty.
Vengeance LPX memory is a new Corsair memory line designed for high-performance overclocking with a low-profile heatspreader is made of pure aluminum for faster heat dissipation and the eight-layer PCB helps manage heat and provides superior overclocking headroom. The memory kits are available in black, red, white, or blue so that enthusiasts, gamers, and modders can add a touch style to match the color scheme of their PC.
Like the DDR3 memory versions, the new Dominator Platinum DDR4 memory kits have a striking industrial design for good looks, patented DHX technology for cooler operation, user-swappable colored “light pipes” for customizable downwash lighting, and Corsair Link compatibility for real-time temperature monitoring. Dominator Platinum memory is built with hand-screened ICs, undergoes rigorous performance testing, and incorporates state-of-the-art cooling for reliable performance in demanding environments.
Vengeance LPX and Dominator Platinum DDR4 Specifications
- Unbuffered DDR4 SDRAM in 288-pin DIMM
- Capacities at launch: 8GB (2x4GB), 16GB (4x4GB), 32GB (4x8GB) and 64GB (8x8GB)
- Speeds at launch: 2666MHz, 2800MHz, and 3000MHz
- Intel XMP 2.0 (Extreme Memory Profile) support
DDR4 is faster. Even at the baseline speed of DDR4 delivers twice the bandwidth with 2133 MT/s (million transfers per second) compared with the base DDR3 1600 MT/s. With optimizations games and applications have the potential to load faster and run more smoothly.
DDR4 uses a lot less power and runs cooler.
With each new generation of CPU and GPU architecture, system power consumption and heat generation become more and more important. DDR4 modules operate at an ultra-low standard 1.2 volts compared to the 1.5 and 1.65 volts of DDR3 memory, allowing DDR4 memory to consume significantly less power and generate less heat.
DDR4 memory modules can get bigger.
DDR3 is limited to 8GB modules for a maximum of 32GB on standard four-socket motherboards. DDR4 will have the ability to enable 16GB per module by 2015. A motherboard with eight memory slots will be upgradeable to an amazing 128GB or DDR4 memory.
Pricing, Availability, and Warranty
Corsair Vengeance LPX Series and Dominator Platinum DDR4 memory kits will be available at the end of August from Corsair's worldwide network of authorized distributors and resellers. The Vengeance LPX and Dominator Platinum memory kits are supplied with a limited lifetime warranty and are backed up by Corsair's customer service and technical support.
Subject: Memory | August 12, 2014 - 02:09 PM | Jeremy Hellstrom
Tagged: XPG V3, DDR3 3100, adata
Currently available for a mere $870 the 8GB DDR3-3100 dual channel kit from ADATA with timings of 12-14-14-36 has to be among the most expensive consumer RAM available on the market. We can only hope that DDR4 does not arrive at a similar speed and price point but instead with slower clocked DIMMs at a more reasonable price and with improvements to performance. Legit Reviews' testing showed that these DIMMs offer almost no benefit over DDR3-1600 with tighter timings in real usage but you can get higher scores on synthetic benchmarks. If benchmarking better than the competition and swap-able heatspreaders with different colours is attractive to you then you could pick up these DIMMs, otherwise you really won't be getting value for your money.
"Gone are the days of being on the cutting edge of memory with DDR3 running at 2133MHz! These days running 2133MHz memory is pretty much considered the norm for a high end gaming rig. If you’re looking to be on the bleeding edge of memory speeds you’re going to be limited to only one or two kits. Today we have one of the fastest kits available on the market to put through the paces, the ADATA XPG V3 DDR3 3100MHz 8GB memory kit. Read on to see if this big dollar kit is worth nearly a thousand dollars."
Here are some more Memory articles from around the web:
- GeIL EVO POTENZA 16GB 2400MHz @ eTeknix
- Kingston HyperX Fury 8GB 1866MHz @ eTeknix
- Patriot Memory 8GB DDR3 1600MHz Viper 3 LP Memory Kit (PVL38G160C9K) Review @ Madshrimps
- GeIL DRAGON RAM 8GB 1600MHz @ eTeknix
Subject: General Tech, Motherboards, Memory | July 6, 2014 - 03:53 AM | Scott Michaud
Tagged: overclocking, memory, gigabyte
About a week ago, HWBOT posted a video of a new DDR3 memory clock record which was apparently beaten the very next day after the movie was published. Tom's Hardware reported on the first of the two, allegedly performed by Gigabyte on their Z97X-SOC Force LN2 Motherboard. The Tom's Hardware article also, erroneously, lists the 2nd place overclock (then 1st place) at 4.56 GHz when it was really half that, because DDR is duplex (2.28 GHz). This team posted their video with a recording of the overclock being measured by an oscilloscope. This asserts that they did not mess with HWBOT.
The now first place team, which managed 2.31 GHz on the same motherboard, did not go to the same level of proof, as far as I can tell.
This is the 2nd fastest overclock...
... but the fastest to be recorded with an oscilloscope that I can tell
Before the machine crashes to a blue screen, the oscilloscope actually reports 2.29 GHz. I am not sure why they took 10 MHZ off, but I expect it is because the system crashed before HWBOT was able to record that higher frequency. Either way, 2.28 GHz was a new world record, and verified by a video, whether or not it was immediately beat.
Tom's Hardware also claims that liquid nitrogen was used to cool the system, which brings sense to why they would use an LN2 board. It could have been chosen just for its overclocking features, but that would have been a weird tradeoff. The LN2 board doesn't have mounting points for a CPU air or water cooler. The extra features would have been offset by the need to build a custom CPU cooler, to not use liquid nitrogen with. It is also unclear how the memory was cooled, whether it was, somehow, liquid nitrogen-cooled too, or if it was exposed to the air.
Subject: Memory | June 11, 2014 - 07:26 PM | Jeremy Hellstrom
Tagged: CAS latency, ddr3-1600, ddr3-1866
X-bit Labs did testing of a variety of memory speeds on Haswell to determine if there is a point of diminishing returns at which point your well earned money is no longer bringing you better performance. By setting up tests of two different DIMMs at set speeds, in this case DDR3-1600 and DDR3-1866 and varying the CAS Latency they tested to see if higher speeds or lower latency gave the best performance. Using both synthetic benchmarks as well as gaming tests they determined that frequency is the key to better performance which makes sense considering the theoretical top frequency of 2933 MHz. Check out all the benchmarks in their full review.
"The development of the new processor microarchitectures goes on and frequencies of contemporary types of DDR3 SDRAM grow as well. Is there any sense in using high-speed memory with modern Haswell processors? To answer this question, we have analyzed DDR3 frequency and timings influence on LGA 1150 platform performance."
Here are some more Memory articles from around the web:
- G.Skill ARES F3-2400C11D-8GAB 2x 4GB DDR3 @ techPowerUp
- Team Group Xtreem 32GB PC3 17000 DDR3 2133 Memory Kit Review @ Madshrimps
- Kingston HyperX Fury 8GB DDR3-1866 CL10 @ Funky Kit
- ADATA XPG V2 2600 MHz RAM Review @ TechwareLabs
Subject: General Tech, Memory, Storage | June 9, 2014 - 11:08 PM | Scott Michaud
Tagged: kingston, ssd, hyperx
Kingston, known primarily for RAM, flash drives, and SSDs, discussed the health of their company. VR-Zone reported on the interview and highlighted the company's sentiments about the PC industry. Long story short, Kingston sees growth in sales of PC gaming hardware -- apparently 20% year-over-year. The company expects that this growth comes primarily from SSD upgrades, either from rotating media or, they claim, replacing years-old, entry-level SSDs with more modern (probably in both speed and size) options.
Nathan Su, APAC (Asia-Pacific) director of Kingston, believes that "many users" have experienced low-tier SSDs and, it seems, would be willing to invest in the full thing. He does not clarify what he means, whether he is talking about SSD caching, or just a really small (or slow) SSDs from drive generations past.
There is a bit of a concern that SSD prices will continue to fall, with some drives reaching under 40c/GB in recent sales. As a consumer, I (selfishly) hope that prices continue to drop, while still remaining profitably sustainable for the manufacturers. Hopefully Kingston is accounting for this and will continue to see growth at the same time.
Subject: Memory, Storage | June 4, 2014 - 11:15 AM | Sebastian Peak
Tagged: ssd, solid state drive, pcie, pci-e ssd, memory, M.2, ddr4, computex 2014, computex, adata, 2tb ssd
ADATA has been showing off some upcoming products at Computex, and it's all about DRAM.
We'll begin with an upcoming line of PCIe Enterprise/Server SSDs powered by the SandForce SF3700-series controller. We've been waiting for products with the SF3700 controller since January, when ADATA showed a prototype board at CES, and ADATA is now showcasing the controller in the "SR1020" series drives.
The first is a 2TB 2.5" drive, but the interface was not announced (and the sample on the floor appeared to be an empty shell). The listed specs are performance up to 1800MB/s and 150K IOPS, with the drive powered by the SF-3739 controller. Support for both AHCI and NVMe is also listed, along with the usual TRIM, NCQ, and SMART support.
Another 2TB SSD was shown with exactly the same specs as the 2.5" version, but this one is built on the M.2 spec. The drive will connect via 4 lanes of Gen 2 PCI Express. Both drives in ADATA's SR1020 PCIe SSD lineup will be available in capacities from 240GB - 2TB, and retail pricing and availability is forthcoming.
Continuing the DRAM theme, ADATA also showed new DDR4 modules in commodity and enthusiast flavors. Both of the registered DIMMs on display (an ultra-low profile DIMM was also shown) had standard DDR4 specs of 2133MHz at 1.2V, but ADATA also showed some performance DDR4 at their booth.
A pair of XPG Z1 DDR4 modules in action
No pricing or availability just yet on these products.
Subject: Memory | April 9, 2014 - 06:54 PM | Jeremy Hellstrom
Tagged: kingston, kingston hyper x, Genesis LoVo, 16GB, ddr3-1600
If you were impressed by the low wattage required to run the AMD AM1 Athlon 5350 and are thinking of building a low power system along the lines of the one Josh used in his review Kingston has a product to help you lower that total system voltage a little more. HyperX Genesis LoVo uses only a mere 1.35V to power the 16GB DDR3-1600 CL9 kit and their low profile helps if you are building a small sized system. Performance at stock speeds is quite decent, with the possibility of overclocking to add more speed if you desire but these DIMMs are more about power savings than raw power. Check out the full review at Funky Kit.
"Even though higher clocked RAM is great for overclocking and gaming for most computer users, memory at lower clocks is good enough for the general tasks they perform daily. For those users, memory speed is usually less important than capacity so today we wish to present something more regular in the memory's world what is Kingston HyperX Genesis LoVo 16GB DDR3-1600 CL9. As probably some readers already noticed, we can't really call it regular memory as Kingston specified it to run at low voltage of 1.35V ... and it's green like most eco-friendly products."
Here are some more Memory articles from around the web:
- G.Skill TridentX 32 GB CAS7 F3-1600C7Q-32GTX @ techPowerUp
- Corsair Vengeance Low Profile 16GB 1600MHz C10 Dual Channel DDR3 Memory Kit Review @ Madshrimps
- AVEXIR Blitz 1.1 Memory Series @ Funky Kit
- Avexir Blitz Series 1.1 4GB 1600MHz Memory @ eTeknix
- Funky Kit Review: G.Skill TridentX 16GB DDR3-1866 CL8 @ Funky Kit
- Avexir Core Series MPOWER 2133 MHz CL9 @ Hardwareoverclock
- Kingston HyperX Predator 8GB DDR3-2400 Kit Review @ OCIA
- Team Group Vulcan Gold 2400MHz 8GB Memory Kit @ Kitguru
- Kingston HyperX Predator 8GB DDR3-2800 CL12 @ Funky Kit
Subject: General Tech, Memory | April 8, 2014 - 02:03 AM | Scott Michaud
Tagged: Hynix, ddr4
... I'll take two.
SK Hynix, one of the leading producers of RAM modules, announced a single stick of DDR4 with 128GB capacity. While this is intended for the server room, I hope that we will see workstation components attempt to be compatible in the near future. It is difficult to find a board that can support more than 64GB at all, let alone twice that, per stick.
As for the typical desktop users? Let's face it, this is overkill, eight times over, generously, per stick. Web browsers are beginning to ring up the memory usage as more and more tabs are loaded simultaneously but, otherwise, there is little use for it for them.
But for those of us who are not them, this could be awesome. It is still unclear how much memory a Haswell-EX motherboard, running on an Intel X99 chipset, will support. I can assume that this stick will not be compatible... but we can always hope, right?
Subject: Editorial, General Tech, Graphics Cards, Processors, Memory, Systems | January 20, 2014 - 02:40 AM | Scott Michaud
Tagged: corsair, overclocking
I rarely overclock anything and this is for three main reasons. The first is that I have had an unreasonably bad time with computer parts failing on their own. I did not want to tempt fate. The second was that I focused on optimizing the operating system and its running services. This was mostly important during the Windows 98, Windows XP, and Windows Vista eras. The third is that I did not find overclocking valuable enough for the performance you regained.
A game that is too hefty to run is probably not an overclock away from working.
Thankfully this never took off...
Today, overclocking is easier and safer than ever with parts that basically do it automatically and back off, on their own, if thermals are too aggressive. Several components are also much less locked down than they have been. (Has anyone, to this day, hacked the locked Barton cores?) It should not be too hard to find a SKU which encourages the enthusiast to tweak some knobs.
But how much of an increase will you see? Corsair has been blogging about using their components (along with an Intel processor, Gigabyte motherboard, and eVGA graphics card because they obviously do not make those) to overclock. The cool part is they break down performance gains in terms of raising the frequencies for just the CPU, just the GPU, just the RAM, or all of the above together. This breakdown shows how each of the three categories contribute to the whole. While none of the overclocks are dramatic, Corsair is probably proud of the 5% jump in Cinebench OpenGL performance just by overclocking the RAM from 1600 MHz to 1866 MHz without touching the CPU or GPU.
It is definitely worth a look.
Subject: Storage, Shows and Expos | January 8, 2014 - 12:57 AM | Allyn Malventano
Tagged: ram, micron, memory, ddr4, CES 2014, CES
While the Crucial did not have much in the way of new flash memory product launches this year, Micron as a whole has been busily churning out further revisions of DDR4 memory. While our visit last year only revealed a single prototype for us to look at, now we have all of the typical form factors covered:
From top down we have enterprise, enthusiast, OEM, and SO-DIMM form factors, all populated with DDR4 parts. All that needs to happen now is for motherboard and portable manufacturers to get on board with the new technology. As with all chicken-and-egg launches, someone needs to take the first plunge, and here we can see Micron has certainly been on the leading edge of things. That enterprise part above is a full 16GB (not bits!) of DDR4 capacity.
Follow all of our coverage of the show at http://pcper.com/ces!
Subject: Memory | January 7, 2014 - 03:49 PM | Jeremy Hellstrom
Tagged: roccat, gaming mat, gaming mouse, mouse caddy
Up for review at Hardware Asylum is a trio of Roccat products, the Kone Pure Optical gaming mouse, the Hiro mousepad and the Apuri mouse cord caddy. The cord caddy is similar to other products we've seen in the past but the inclusion of powered USB 2.0 ports is an nice addition to an otherwise superfluous peripheral. The mousepad is made of stain resistant silicone and measures 350 x 250 x 2.5mm which should fit on most desks. The Kone mouse sports a 4000 DPI Pro-Optic sensor, 576kB on-board memory for macros as well as the ability for you to utilize your keyboard in conjunction with the mouse thanks to the rather comprehensive software suite.
"All paired together, the Kone Pure Optical, Apuri and Hiro make a nice setup that provides a lot of utility and versatility inside and out of games, and all without breaking the bank. This trio can be acquired for the cost of just a high grade laser mouse alone, and it will perform and feel great in many gaming and working environments."
Here is some more Tech News from around the web:
- Mionix Avior 7000 gaming mouse @ Rbmods
- CM Storm Havoc Gaming Mouse @ techPowerUp
- Mionix NAOS 8200 High Performance Gaming Mouse @ NikKTech
- Roccat Kone XTD Gaming Mouse Review @ Hardware Asylum
- Gigabyte Aivia Osmium Cherry Brown Mechanical Gaming Keyboard (GK-OSMIUM BRN) Review @ Bjorn3D
- Func KB-460 keyboard Review @ Bjorn3D
- Thermaltake Ttesports MEKA G-Unit Illuminated Keyboard Review @ TechwareLabs
- Thermaltake Ttesports MEKA G1 Illuminated Keyboard Review @ TechwareLabs
- Tt eSPORTS MEKA G-Unit Red Switch Mechanical Keyboard Review @ Techgage
Subject: General Tech, Memory | January 1, 2014 - 03:37 AM | Scott Michaud
Tagged: RDIMM, ram, LRDIMM
In all honesty, outside of on-die graphics solutions, memory speed and latency are often neglected. My only requirements for RAM beyond the recommended specs for my motherboard and processor has been a heat spreader of some sort (and that is just because I have bad luck with several DOAs on unshielded RAM which I assume was handling problems).
But this story is for the enterprise users.
Johan De Gelas of AnandTech decided to test a few different configurations of RAM including both RDIMM and LRDIMM modules. LRDIMMs are significantly more expensive than the cheaper RIMM modules but, especially if you could reduce server count (and active licenses of software running on them) they wanted to investigate whether it could be cheaper overall. This would not be the case if software is completely CPU-limited... but, again, when is memory the limiting factor?
That is where the benchmarks come in. Among the handful of measurements performed, they simulated thousands of users accessing a CDN with between one-to-three-quarters of a terabyte of memory. In both cases, 768GB of LRDIMM memory had significantly higher throughput and significantly lower latency.
As always, check out the review if you are interested.