NZXT adds a trio of cases to their lineup, and a brain as well

Subject: Cases and Cooling | October 19, 2017 - 07:37 PM |
Tagged: H700i, H400i, H200i, nzxt, Grid+ V3, CAM

To start with the most interesting of the four product announcements from NZXT, take a look at the Grid+ V3.  This is a smart fan controller which offers both voltage and PWM control via the CAM software suite.

large_4068bef381db0e33.png

There are six separate channels on the Grid, allowing you to control each fan individually or you can use the included splitters to add more than one fan to a channel.  You are able to choose between manual control or the Adaptive Noise Reduction feature to allow the device to determine the proper fan curves for your system, even if you swap hardware after the initial setup.

Grid+v3-system-S340Rear_preview.jpeg

Along with their advanced fan controller, NZXT announced three new cases, the H700i, H400i, and H200i.  The H700i is a full sized case standing 230x494x494mm and is capable of holding even eATX motherboards with seven slots.  It is also a good choice for data hoarders, with seven 2.5" bays and up to three 3.5" bays. It is available now for $200.

H700i_Matte BlackBlue_Front Fans_preview.jpeg

The H400i is the mATX case, a svelte 210x393x421mm in size but still able to handle a pair of 120/140mm fans or radiators in the front, behind the filters you can see as the front panel has been removed in the picture below.  It will be available late next month for $140.

H400i-Matte Black_FrontFilter_preview.jpeg

Last, and only least in volume is the H200i, the mini-ITX case.  At 210x334x372mm and 6kg in weight it is not quite as small as a NUC, good news for those of us who need a bit of space to manoeuvre when installing components.  It will arrive before the end of the year, for about $120.

H200i-Matte White_Top45_preview.jpeg

All of the above cases are constructed with SECC steel and tempered glass side panels, available in matte black or white as well as matte black with blue or red trim.  The cases are compatible with the CAM software mentioned previously and have space to install the GRID+ V3 digital controller.  Your R's G's and B's can be managed through NZXT's HUE+ software, with support for numerous LED strips as well as ones built into your components.  Aer F fans are included or you could take advantage of the drop-in brackets and integrated reservoir mounting to switch to watercooling. 

 

Source: NZXT

Cooler Master releases the MasterCase H500P and MasterBox MB600L

Subject: Cases and Cooling | October 10, 2017 - 03:25 PM |
Tagged: MasterBox MB600L, MasterCase H500P, cooler master

Today CoolerMaster announced two cases, the MasterCase H500P and MasterBox MB600L and there are already some reviews of the MasterCase posted, which you can see below.  The MasterBox MB600L is larger and less flamboyant than the MasterCase and is a better choice for those of us who prefer less RGBs in their lives.

MB600L.png

The MB600L will accommodate GPUs of up to 400mm, heatsinks 160mm in height or radiators of 360mm if you prefer watercooling.  You can get the MB600L in red, blue and gunmetal exteriors and there will be models with an optical bay if you do still use DVDs.  The case will sell for $50 and is available now.

500.png

The MasterCase H500P is for those who want a case that stands out, the front panel shows off two 200mm RGB fans which can be controlled from compatible motherboards and there is space for two more to be installed on the top.  If you prefer watercooling, you can replace the fans in both positions with up to a 360mm radiator.  There are two PCI slots at the rear of the H500P so you can vertically mount your GPU to show it off, without needing additional brackets. 

You can see some reviews of the MasterCase below.

CASES & COOLING

Source: CoolerMaster

Now that's a waterblock! Cooling ThreadRipper with Enermax's Liqtech AIOs

Subject: Cases and Cooling | October 6, 2017 - 03:16 PM |
Tagged: amd, ryzen, Threadripper, AIO, watercooler, enermax, Liqtech, TR4 240, TR4 360

As you can see in the picture, Enermax's Liqtech coolers are large enough to completely cover AMD's supersized new processors.  [H]ard|OCP found that the installation process "could not be much simpler", with great contact and an saw an even distribution of thermal compound when they checked.  As you might expect, the model numbers refer to the size of the radiator, the 240 sports a pair of 120mm fans while the 360 sports three for those systems which can accommodate the larger size.  The coolers were not able to keep a 1950X stable at 4GHz but kept the temperatures well below 80C at 3.9GHz; this along with the prices of $130 and $150 respectively show that these coolers are aimed at those on a budget who are not planning on overclocking.  You can see the full results here.

1507048599a92j9qtgtx_2_10_l.jpg

"Enermax brings to us the first All-in-One coolers that are purpose-built for AMD's Ryzen Threadripper CPUs. We review both the Liqtech TR4 240 and the Liqtech TR4 360 using our overclocked 1950X Threadripper system and compare these to our XSPC RayStorm custom cooling loop. Yes, we are setting the bar high."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

Source: [H]ard|OCP

Just Delivered: Cryorig H5 Ultimate CPU Cooler

Subject: Cases and Cooling | September 30, 2017 - 02:26 AM |
Tagged: tower cooler, just delivered, FM2+, cryorig h5 ultimate, CRYORIG, air cooling, air cooler

Just Delivered is a section of PC Perspective where we share some of the goodies that pass through our labs that may or may not see a review, but are pretty cool none the less.

Find the Cryorig H5 Ultimate on Amazon!

I have been slowly rebuilding my wife's desktop PC following a failure of the all-in-one liquid CPU cooler that saw leaking coolant kill the motherboard and power supply (surprisingly the GTX 750 Ti survived despite getting a bunch of coolant on it). I recently replaced the motherboard and PSU (while discovering FM2+ boards are still pretty expensive on eBay) and today got in the last component: a Cryorig H5 Ultimate air cooler. I wouldn't mind replacing the TD03 with another water cooler (it was nice and quiet when it worked), but got a good deal on the air cooler. Anyway, the Cryorig H5 Ultimate is a monster tower style air cooler measuring 168.3 x 143 x 110.9 (HxWxL) with the included fan and weighing 920 grams (2.03 pounds).

Cryorig H5 Ultimate Unboxing.png

I forgot to take an unboxing picture, here is what it comes with though (from Cryorig's website).

The Cryorig H5 Ultimate is rated at 180W TDP and features 38 aluminum fins in an interesting hive / honey comb design that allegedly reduces noise, improves air flow, and strengthens the fin stack. The fins are connected with four 6mm copper heat pipes to the nickel plated C1100 copper baseplate. A 140mm XF140 fan (76 CFM) pushes air through the fin stack spinning anywhere between 700 and 1300 RPM with rated noise levels of 19 to 23 dBA respectively.

Cryorig H5 Ultimate installed on AMD FM2 A75.jpg

There are no LEDs on this monster, but it doesn't need them to look good in my opinion. Fortunately, the fan height is adjustable and you are able to mount the fan on either side of the heatsink which will be important because it can and will interfere with your RAM modules depending on your motherboard and height of RAM heat spreaders! As you will see, I ran into this, but my PC chassis gave just enough clearance that I was able to move the fan up enough to clear the G.Skill RAM (which is on the shorter side). The fan is mounted using two wires and is fairly easy to take off and install.

Cryorig supports both AMD and Intel motherboards (including AM4 with a separate mounting upgrade kit) including FM1, FM2, AM2, and AM3 on the AMD side and LGA 775, 1156, 1150, 1151, and 2011 on the Intel side. The cooler has two mounting kits for AMD and Intel with both requiring you install a backplate.

Cryorig H5 Ultimate AMD Mounting Kit.jpg

In my case, I am installing the Cryorig H5 Ultimate on a FM2+ socket motherboard. I had to unscrew the default AMD mounting system and install Cryorig's backplate. There are four screws that screw onto the backplate posts with a slight bit of give which is normal (the backplate will not be tightly screwed to the board, it should be able to move a bit). Then another bracket is screwed onto the backplate screws until hand tight (tighten them using the X method going corner to diagonal corner).

Easy enough so far! However, now here is where I ran into some trouble with the installation. Much like the experience of installing RAM for the first time where you can sometimes feel like you need to use a lot more force than you think you should need to install them, the Cryorig cooler takes quite a bit of force to properly install. Learn from my frustration:

20170617_235512.jpg

After applying your thermal paste, it's time to install the cooler. You will notice that there are two holes in the top of the cooler and two screw holes in the bracket you installed over the CPU socket. You will line the cooler up so that the spring mounted screws on the cooler are over the holes in the bracket. I found it easiest to put my finger by one of the screws and make sure that screw was lined up, then let down the other side of the cooler so that both screws are lined up. Now, you will need the special screwdriver Cryorig provides in the box. Using one hand push down on the cooler and use the other hand to stick the screwdriver in one of the holes. You will need to keep pressure on the cooler while turning the screw so that it can catch onto the threads in the bracket and start, well, screwing in.  Make a few turns so that it is in, but do not fully tighten the screw down. Now, move your hand to the opposite side of the cooler where the other screw hole is and press down. You will need to push this side of the cooler down with quite a bit of force (again, thinking back to the RAM example, don't hulk smash anything, but don’t' be too gentle either). While keeping pressure on this side to hold it towards the socket, start screwing down this side of the cooler. (If you did it right the other side won't pop out, if you didn't screw the first side down enough it might pop out and you'll have to start over heh) Once both sides are partially in, just alternate screwing the screws down until they are hand tight.

Trust me, you might think you are going to break this thing or bend something, but it's just normal SOP. Finally, plug in the XF140 fan into the CPU_fan header and you're good to go!

20170919_022250.jpg

The Cryorig H5 Ultimate dwarfs my GA-F2A78M-HD2 mATX motherboard leaving just enough room for two memory DIMMs and the graphics card! Heck it still looked huge installed in the old A88X ATX board!

Since installing it I have been playing around a bit with the PC trying to get some temperature readings for you, but am discovering that getting accurate temperature readings from AMD processors (especially older APUs) is not that easy. I am still testing things out and looking into overclocking, but best I can tell the Cryorig cooler is keeping the AMD A8 5600K processor somewhere around 55°C under load using AIDA64 stress testing. At idle the cooler is very quiet and while it does ramp up under load it is barely audible compared to the case exhaust fan! This is not a formal review but so far it has been an interesting cooler assuming you can find it at a good price.

20170919_032821.jpg

It's alive!!

If you are interested in a monster cooler like this, definitely double check your case and RAM clearances though. The install was not too bad the second time around (I first installed it on her old motherboard not knowing if it was dead yet as I did not have another cooler to test), but it is not as easy on this AMD FM2+ socket as their video (and others I found on YouTube) makes it look for the intel platform! With the knowledge that you can and need to use force to press it down to get the screws in it's a fairly quick install, I just wish that information was better spelled out in the instructions as it would have saved me a ton of time the first go around! I don't have formal noise or temp numbers as I am just starting to test it, but so far, I am happy with it.

Source: Cryorig

Cooler Master Cosmos C700P; size of the entire universe man ...

Subject: Cases and Cooling | September 28, 2017 - 01:04 PM |
Tagged: cooler master, cosmos C700P, cosmos, XL-ATX

Monolithic is a word that instantly springs to mind when you see the CM Cosmos C700P.  It stands at 639x306x651mm (25.2x12x25.6") and weighs in at 26.2 kg (57.8lbs) naked, fitting every style motherboard from XL-ATX down to Micro-ATX.  Creative souls might be able to fit a few mATX boards in this beast.  As befits a case of this stature, the front panel includes a USB 3.1 Gen 2 Type C port and four USB 3.0 ports in addition to audio jacks and RGButtons.  The interior is something you need to behold, thankfully the Guru of 3D offers plenty of pictures in their full review

img_8389.jpg

"We review the Cooler Master Cosmos C700P which they released today. the legend is back in a new 2017 jacket! That means included RGB LED system, tempered glass side panel with not one but two bends, and an immensely intricate inside with covers and shields everywhere."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

Source: Guru of 3D

Seasonic's PRIME family now features a 650W Platinum model

Subject: Cases and Cooling | September 27, 2017 - 02:35 PM |
Tagged: seasonic, PRIME PSU, 80 Plus Platinum, 650W

Lee has reviewed several of Seasonic's PRIME PSUs, focusing on the higher wattage models and awarding high honours for the models tested.  Not everyone needs a kilowatt class PSU however, which makes [H]ard|OCP's review of the new 650W member of the PRIME family interesting.  Externally the PSU is indistinguishable from the higher wattage models, it is only in the interior that you can see the differences.  Those differences do not have an effect on the quality of power provided by this PSU, as [H] describes it as the best 650W model they have seen to date.  The price is a little higher than other 650W PSUs, making the 850W model a better deal for some.  Drop by to get the full story.

150454301442q7i5obio_3_8_l.jpg

"This time we review a small Seasonic rated at 650 watts, but this one is part of its flagship Prime series with Platinum rated efficiency. That means, less heat, less noise, and a lower cost of operation over time. So, is the PRIME 650 Platinum PSU worthy of Seasonic's flagship status? We will surely find out."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

Source: [H]ard|OCP

Noctua Focused on Ryzen with NH-L9a-AM4 and NH-L12S Low-Profile Coolers

Subject: Cases and Cooling | September 25, 2017 - 10:43 AM |
Tagged: ryzen, noctua, low-profile, htpc, cooler, APU, amd, AM4, air cooling

AMD's popularity with Ryzen CPUs (and upcoming APUs) has made waves across the industry, and Noctua have jumped in with a pair of low-profile offerings that update previous designs for cramped case interiors.

First up is the new version of the NH-L9a:

noctua_nh_l9a_am4_1.jpg

"The new NH-L9a-AM4 is an AM4-specific revision of Noctua’s award-winning NH-L9a low-profile CPU cooler. At a height of only 37mm, the NH-L9a is ideal for extremely slim cases and, due to its small footprint, it provides 100% RAM and PCIe compatibility as well as easy access to near-socket connectors, even on tightly packed mini-ITX motherboards."

Next is the new NH-L12S:

noctua_nh_l12s_1.jpg

"The new S-version of the renowned NH-L12 not only adds AM4 support but also gives more flexibility and improved performance in low-profile mode. Thanks to the new NF-A12x15 PWM slim 120mm fan, the NH-L12S provides even better cooling than the previous model with its 92mm fan. At the same time, the NH-L12S is highly versatile: with the fan installed on top of the fins, the cooler is compatible with RAM modules of up to 45mm in height. With the fan installed underneath the fins, the total height of the cooler is only 70mm, making it suitable for use in many compact cases."

Noctua says that these new coolers now shipping "and will be available shortly", with an MSRP of $39.90 for the NH-L9a-AM4 and $49 for the NH-L12S.

Source: Noctua

More Threadripper waterblocks, including an unfamiliar name

Subject: Cases and Cooling | September 19, 2017 - 03:59 PM |
Tagged: XSPC, water cooler, Threadripper, RayStorm Neo, Bykski, amd, A-RYZEN-Th-X

[H]ard|OCP have been hard at work testing a variety of Threadripper compatible AIO watercoolers, sometimes with their own adapters as these products are very new.  They just revisited the XSPC RayStorm Neo which performed exceptionally and also note that the retail version will not feature mounting for AM4 processors.  The second waterblock they tested was the Bykski A-RYZEN-Th-X, not a familiar name but also a very effective choice for cooling ThreadRipper processors.  Take a look at the testing process as well as their recommended methods for properly spreading thermal paste on AMD's new big silicon.

1504742086n1f4pi37ul_1_1_l.jpg

"We have been waiting for AMD Threadripper CPU custom cooling parts to make their way to us. We have our first two purpose-built Threadripper waterblocks from XSPC and Bykski. We put both these coolers to the test with our 4GHz overclocked Threadripper in hour long stress tests to see how our temperatures fare."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: [H]ard|OCP

Threadripper cooler on an AM4 socket? Yes, you can!

Subject: Cases and Cooling | September 12, 2017 - 02:57 PM |
Tagged: amd, Threadripper, ryzen 7, AM4, XSPC RayStorm

The question is if installing the XSPC RayStorm Threadripper waterblock on an AM4 actually improves your systems thermals.  [H]ard|OCP tested out the difficulty of the installation process and the performance of the cooler on a Ryzen 7 1700X overclocked to 4GHz.  The mounting worked exactly as advertised, mating perfectly with the AM4 processor; the performance on the other hand demonstrates the advantage of using coolers specifically designed for your processor.

1505231178a1xznfj1vf_1_4_l.jpg

"If you could mount your Threadripper custom cooling waterblock on your socket AM4 Ryzen 7 CPU, wouldn't you? Of course the answer is yes. However, the results turned out a bit different than we thought those might."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: [H]ard|OCP

Sixth of its name, the new CM MasterCase Pro

Subject: Cases and Cooling | August 29, 2017 - 03:11 PM |
Tagged: coolermaster, MasterCase Pro 6

The MasterCase Pro 5 was released a few years back which is why it is time for a MasterCase Pro 6 review.  CoolerMaster kept the modular design, making the installation of fans or radiators much easier as well as allowing you to remove drive cages you do not require.  The difference between this model and its predecessor are the design of the top and front panels, the similarity is the slightly imperfect mating of various parts of the case.  The Tech Report did still find the case easy to work with, take a closer look here to see if its style matches yours.

mastercasepro6-innards-2.jpg

"Cooler Master's MasterCase Pro 6 puts a sharp new face on the company's tried-and-true modular chassis. We popped in our test system to see whether this case's pop-out vents are a cool new idea in case design."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Is be quiet's Pure Power 600W PSU a 10?

Subject: Cases and Cooling | August 25, 2017 - 06:03 PM |
Tagged: be quiet!, modular psu, 600w, Pure Power 10, 80 PLUS Silver

Kilowatt class PSUs such as the Seasonic PRIME Platinum which Lee just reviewed are impressive and up to the task of powering the most powerful of systems but for most they are overkill.  For the majority of us, something in a 600W model will be sufficient for our needs as well as being more efficient.  A little while back [H]ard|OCP took a look at be quiet's Pure Power 10 600W 80 PLUS Silver modular PSU, the first be quiet! to meet their benchmarking table.  It operated quietly and it was handsomely built, however once they started testing the PSU simply could not take the heat.  If you live somewhere which never reaches 30C ambient this might be an acceptable solution but for the rest of us ... the review reveals a significant issue.

1497811993xh7owgw6ni_2_9_l.jpg

"This may come as a shock to you, but be quiet! power supplies are all about...wait for it...exceptionally quiet operation. However that is not the only virtue the Pure Power 10 series extols. be quiet tells us that this PP10 has "peerless dependability" and "best-in-class features." Let's see if we can set it on fire!"

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: [H]ard|OCP

The Enermax LIQMAX II 240 shunts away 250W of TDP

Subject: Cases and Cooling | August 18, 2017 - 02:14 PM |
Tagged: LIQMAX II 240, enermax, AIO

Enermax's LIQMAX AIO cooler has not received a lot of attention, in the case of [H]ard|OCP they were less than impressed with the choice to locate the fan controller on the hub.  The second generation has remedied that issue by moving the switch to the side of the fans which makes it much more convenient when you need to adjust it.  They also praise the evolution of the mounting brackets which have become easier to install with every new generation, though on a Threadripper you will still need to use AMD's bracket to install the LIQMAX II.  Overall, the performance exceeded their expectations, for an $80 AIO solution it is quite effective albeit somewhat loud on the highest setting.  Drop by for a look at their full review.

1501379033rpqd5hmlpn_2_8_l.jpg

"Enermax is extremely proud of its Liqmax II 240 CPU AIO cooler. It is one of the few coolers you will find that it proudly displays its TDP rating right on the front of the box, which happens to be "350W+." With its Batwing fan blades, ceramic bearing pump, and Shunt-Channel-Technology it is a sure winner, right? Let's find out."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: [H]ard|OCP

Lian Li’s new PC-Q39 tempered glass Mini-ITX (wide) tower

Subject: Cases and Cooling | August 16, 2017 - 06:21 PM |
Tagged: tempered glass, PC-Q39, mini-itx, Lian Li

Lian Li have released an upgrade to the PC-Q37 with the new mini-ITX PC-Q39 with tempered glass side panel and a larger internal volume.  The aluminium case will be large enough to fit a three slot GPU, with the extra width allowing a separated second chamber to house an ATX PSU of up to 160mm. 

q39-00.jpg

In addition to the PSU there is space for a pump and reservoir for watercooling as well as mounting points for two 3.5” and one 2.5” drive, allowing you to configure an unobstructed view of your components and he almost mandatory RGB LED lightshow which they produce.  If you do chose to watercool, a radiator of up to 240mm can be mounted at the top while the bottom of the case will accommodate two 120mm fans or a single 140 fan.

q39-10.jpg

The front panel has a minimalist design, the various connectors have been moved to the top of the case.  There is now a USB 3.1 Type-C plug in addition to two USB 3.1 plugs, audio jacks and a power button.  The shield at the top of the case is removable to make it easier to mount your fans or radiator as well as making it easy to clean. 

The MSRP is $210 and it is available now at NewEgg and other fine retailers.

q39-07.jpg

Click for the full PR.

Source: Lian Li

EK's Threadripper Supremacy EVO water blocks

Subject: Cases and Cooling | August 11, 2017 - 05:45 PM |
Tagged: X399, watercooling, Threadripper, EK Supremacy EVO, amd

EK Waterblocks have announced the EK Supremacy EVO full cover waterblock and cold plate for the new AMD Threadripper processors.  You have your choice of Nickel, Acetal and Nickel or Full Nickel models, depending on your preference.

unnamed.jpg

You can order it now, they will not start shipping until August 18th and EK will be honouring preorders first, if that is your type of thing.  The Supremacy EVO will be large enough to cover the entire heatspreader on the Threadripper so you will not need adapters or various interesting techniques to make sure your new processor will stay cool.  Inside are 52 grooves with a spacing of 0.25mm apart, making use of that extra space.  Hopefully we will soon receive some for testing; at least Morry certainly hopes so!

unnamed2.jpg

Click for the full PR ...

If you like asymmetry then Fractal Design has your case

Subject: Cases and Cooling | August 11, 2017 - 02:27 PM |
Tagged: fractal design, meshify c

It may not be obvious from the one picture but the front facing of the Meshify C has an interesting pattern while the mesh on the top and bottom of the case remain flat.  That should give you a unique look without interfering with the stability of the case.  As with many newer cases the PSU is installed at the bottom of the case, with a shroud separating it from the rest of the system.  The tempered glass side panel does not add much to the cost, the MSRP of $89.99 is quite reasonable for a case such as this.  Check out how it looks with components installed over at Benchmark Reviews.

Fractal-Design-Meshify-C_00002.jpg

"When Fractal Design offered up yet another, as-of-yet unannounced product to add to their lineup my curiosity was piqued. What else could they possibly have in store? All I had was a product name: the Meshify C. I could hazard a few guesses as to the nature of this new case: ATX, based on the Define C no doubt, with a dressing of mesh – perhaps an Arc Midi successor? Follow along as Benchmark Reviews investigates this new direction from Fractal Design."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

I Think They're Big Fans of AMD Threadripper and EPYC... Noctua Announces Three New Coolers.

Subject: Cases and Cooling | August 3, 2017 - 08:41 PM |
Tagged: noctua, amd, Threadripper, EPYC

Noctua has announced three new heatsinks for AMD’s new high-end CPU platforms, Threadripper and EPYC. If you’ve been following the company, or Morry’s motherboard reviews, then you know that these coolers are huge (and effective).

noctua-2017-threadripper-cooler.png

Apparently the main difference is the contact surface, 70mm x 56mm, to accommodate for the processor’s large package. AMD connects multiple dies together with their Infinity Fabric, which means a huge total surface area. The cooler comes in three sizes, corresponding to the fan that’s intended to be used with it: 140mm (NH-U14S TR4-SP3), 120mm (NH-U12S TR4-SP3), and 92mm (NH-U9S TR4-SP3).

The two “smallest” sizes, NH-U12S and NH-U9S, are both expected to retail for $69.90 USD, so I guess choose whichever makes the most sense for your system. The largest one, the NH-U14S, is $10 more expensive at $79.90 USD. They should be available by the end of the month.

Source: Noctua

FSP releases a trio of Platinum PSUs

Subject: Cases and Cooling | August 2, 2017 - 01:30 PM |
Tagged: FSP Group, modular psu, 750w, 650W, 550W, Hydro PTM, 80 Plus Platinum

FSP Group have just released three new 80 Plus Platinum Hydro PTM modular PSUs, in 750W, 650W and 550W models.  The Hydro branding comes from the fluid dynamic bearings in the 135mm fan which they have optimized for quiet operation.

Hydro PTM-750W_002.jpg

The 750W model has a pair of 4+4 power plugs for X299 users, the other two models will not though all will use ribbon cables to help you with cable management.  Internally you will find Japanese industrial grade electrolytic caps and a single 12V rail which will provide higher quality power than multiple rail designs.   All models will come with a 10 year warranty.

PR below the fold.

Source: FSP Group

NZXT Kraken X62, X52 and X61 compatible with AMD Ryzen Threadripper

Subject: Cases and Cooling | July 31, 2017 - 01:49 PM |
Tagged: nzxt, kraken, Kraken X62, Kraken X52, Kraken X61, Threadripper, amd

NZXT has announced that their three popular AiO watercoolers, the Kraken X62, Kraken X52, and Kraken X61 will be compatible with Threadripper, arriving soon to retailers.   

unnamed.png

NZXT has been working with AMD and created an adapter for SocketTR4 to allow you to use their cooler in your new system.  The retention clip will be supplied by AMD, in the package the new CPUs.  This is a good thing, considering the unique new way in which you install Threadripper processors.  If you haven't seen the video demonstrating the installation process you can see it below.

 

Source: NZXT

Build your own watercooling loop with the EKWB L360 2.0 Kit

Subject: Cases and Cooling | July 24, 2017 - 02:34 PM |
Tagged: watercooler, EKWB, EK-KIT

EKWB's L360 2.0 Kit is a ~$250 pre-compiled watercooling kit which includes a EK-Supremacy MX waterblock, EK-CoolStream PE 360mm radiator with three EK-Vardar F3-120mm fans, EK-XRES 100 DDC MX 3.1 PWM pump and reservoir, 2m of tubing plus compression fittings and a container of EK-Ekoolant EVO Clear coolant concentrate, good for 1l of coolant once diluted. All you need to do is assemble the kit and install it in your system.  Modders-Inc did just that, the installation process was enjoyable and far more effective than air cooling.  If you did plan to add in a GPU waterblock EKWB recommends adding in another radiator which should make your cooling even more effective. 

Check out the full review here.

ek_img_md00031.jpg

"EKWB has been in watercooling since its meager beginnings in 1999. Every package, every kit, every block advancing the genre of watercooling. As the critical mass for watercooling began to grow, and the knowledge barrier for putting these kits into your system began to fall, companies have been putting together pre-compiled kits of components to make it easier on the …"

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: Modders Inc

CRYORIG's A40; two heads are better than one?

Subject: Cases and Cooling | July 21, 2017 - 03:49 PM |
Tagged: CRYORIG, CRYORIG A40, AIO, water cooler

The CRYORIG A40 is not a new cooler but its unique design is worth revisiting for those who have forgotten about its existence.  Instead of having a single area in which to dump heat, the pump assembly mounted to the CPU also has its own fan.  That fan did not not noticeably decrease the CPU temperatures when TechPowerUp tested it, however for SFF systems and other builds with components which could benefit from airflow inside the case that fan is more than just a gimmick.  Check out the full review here.

title.jpg

"The A40 by CRYORIG is the company's entry level offering in their all-in-one hybrid liquid CPU cooler lineup. It lacks the size of the A80 and the radiator thickness of the A40 Ultimate. However, unlike the others, it offers a more affordable price point with all the same features."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: TechPowerUp