Computex 2017: BitFenix Shows Off Affordable Mid-Tower With RGB and Tempered Glass

Subject: Cases and Cooling | June 3, 2017 - 11:16 PM |
Tagged: computex, bitfenix, mid tower, E-ATX Case, RGB LED, gaming, tempered glass

BitFenix had several new PC cases on display at its Computex booth, but the one that caught my eye was the sub-$100 Enso mid-tower that has some premium features including a large tempered glass side panel, RGB LED and fan controllers, removable filters, and various cable management features. The BitFenix Enso has a clean design that out of the box limits the RGB to a nice looking front panel while allowing enthusiasts to go crazy with aftermarket LED strips and LED fans if they wish.

View Full Size

The BitFenix Enso mid-tower (Image credit: KitGuru)

The new Enso chassis measures 8.2" x 19.2" x 14.4" (209 x 487 x 442mm).and is clad in all black with clean lines and edges that strikes a balance between boxy and gaudy (heh). The front is a smooth panel that slightly angles out (no external drive support here) with RGB LEDs in all four corners. The front I/O is up top with two USB 3.0, two audio, and power and reset buttons. The left side is almost entirely comprised of a tempered glass side panel that is held on by black thumbscrews.

The top has a mesh grill with support for two 120mm fans along with a removable magnetic fan filter. There is also room for a 120mm fan in the back and two 120mm fans up front (where there is also a removable filter that pulls out from the left side of the front panel). There is not enough room up top for a water cooling radiator up top, but there is plenty of room for up to a 240mm radiator in the front.

The bottom of the case has a compartment for the bottom mounted up to 220mm power supply (which also has a removable dust filter) and two 3.5” drives along with space to hide excess cables. This area is covered by a simple black shroud that should make cable management easier.

Dropping support for external drive bays and extra 3.5” bays, BitFenix is able to support E-ATX motherboards, long graphics cards (up to 320mm, their demo used an Asus Strix GTX 1080), and water cooling radiators in a compact mid-tower case. BitFenix states it is possible to mount a 360mm radiator in the front, but it the specifications suggest if you would be limited to two fans with matching vents.

View Full Size

Lots of tie downs and space to hide cables! (Image credit: Bitwit Kyle)

The right side panel is blank, and removing it reveals the back of the motherboard tray. There is room for three 2.5” SSDs with one behind the motherboard and two behind the front fans. The motherboard tray has a large CPU cutout, lots of spots to tie up cables, and rubber grommets for passing cables through to the motherboard and graphics card. Having move of the components sitting behind the motherboard tray means that making a clean looking build will be a bit easier (no drive power cables to hide).

The front panel RGB LEDs are “addressable” which is to say that they can be controlled via the controller at the back or via software where BitFenix is working with Asus to allow its RGB LEDs to be controlled with its Aurora software. There is also a fan controller that looks to accept PWM and control 3-pin fans from that signal. The case is also compatible with LED fans and LEDs strips (the BitFenix demo used strips from Asus that could be controlled with the Asus software). As far as the front panel, you can choose a color or activate a gentle pulsing color change mode that cycles through the colors of the rainbow.

View Full Size

(Image credit: Bitwit Kyle)

Out of the box, the BitFenix Enso will have the front panel LEDs and controllers, but users will need to purchase fans and/or LED strips separately. This is not necessarily bad news though because it allows enthusiasts to pick the fans and LEDs they want (or don’t want), and it also allows the case to hit the budget sub-$100 market with lots of nice DIY-friendly features.

According to a BitFenix representative, the BitFenix Enso will arrive around the end of Q3 2017 or towards the beginning of Q4 with an MSRP of $79.

It looks like an impressive budget case, and if they can hit that $79 target it should be a great value that will let you show off your DIY build without breaking the bank! From the videos at Computex, I am really liking the design as well. What are your thoughts?

Source: Tech City

Video News


April 25, 2019 | 12:16 AM - Posted by JeaSaxofs (not verified)

Cialis Soft Prezzo [url=http://via100mg.com]buy viagra[/url] Amoxicillin Dosage For Cats Capsule Best Price Cialis 5 Mg 315

April 25, 2019 | 12:18 AM - Posted by JeaSaxofs (not verified)

Cialis Soft Prezzo [url=http://via100mg.com]buy viagra[/url] Amoxicillin Dosage For Cats Capsule Best Price Cialis 5 Mg 315

Post new comment

The content of this field is kept private and will not be shown publicly.
  • Lines and paragraphs break automatically.
  • Allowed HTML tags: <a> <em> <strong> <cite> <code> <ul> <ol> <li> <dl> <dt> <dd> <blockquote><p><br>
  • Web page addresses and e-mail addresses turn into links automatically.

More information about formatting options

CAPTCHA
This question is for testing whether you are a human visitor and to prevent automated spam submissions.