If you like asymmetry then Fractal Design has your case

Subject: Cases and Cooling | August 11, 2017 - 02:27 PM |
Tagged: fractal design, meshify c

It may not be obvious from the one picture but the front facing of the Meshify C has an interesting pattern while the mesh on the top and bottom of the case remain flat.  That should give you a unique look without interfering with the stability of the case.  As with many newer cases the PSU is installed at the bottom of the case, with a shroud separating it from the rest of the system.  The tempered glass side panel does not add much to the cost, the MSRP of $89.99 is quite reasonable for a case such as this.  Check out how it looks with components installed over at Benchmark Reviews.

Fractal-Design-Meshify-C_00002.jpg

"When Fractal Design offered up yet another, as-of-yet unannounced product to add to their lineup my curiosity was piqued. What else could they possibly have in store? All I had was a product name: the Meshify C. I could hazard a few guesses as to the nature of this new case: ATX, based on the Define C no doubt, with a dressing of mesh – perhaps an Arc Midi successor? Follow along as Benchmark Reviews investigates this new direction from Fractal Design."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

I Think They're Big Fans of AMD Threadripper and EPYC... Noctua Announces Three New Coolers.

Subject: Cases and Cooling | August 3, 2017 - 08:41 PM |
Tagged: noctua, amd, Threadripper, EPYC

Noctua has announced three new heatsinks for AMD’s new high-end CPU platforms, Threadripper and EPYC. If you’ve been following the company, or Morry’s motherboard reviews, then you know that these coolers are huge (and effective).

noctua-2017-threadripper-cooler.png

Apparently the main difference is the contact surface, 70mm x 56mm, to accommodate for the processor’s large package. AMD connects multiple dies together with their Infinity Fabric, which means a huge total surface area. The cooler comes in three sizes, corresponding to the fan that’s intended to be used with it: 140mm (NH-U14S TR4-SP3), 120mm (NH-U12S TR4-SP3), and 92mm (NH-U9S TR4-SP3).

The two “smallest” sizes, NH-U12S and NH-U9S, are both expected to retail for $69.90 USD, so I guess choose whichever makes the most sense for your system. The largest one, the NH-U14S, is $10 more expensive at $79.90 USD. They should be available by the end of the month.

Source: Noctua

FSP releases a trio of Platinum PSUs

Subject: Cases and Cooling | August 2, 2017 - 01:30 PM |
Tagged: FSP Group, modular psu, 750w, 650W, 550W, Hydro PTM, 80 Plus Platinum

FSP Group have just released three new 80 Plus Platinum Hydro PTM modular PSUs, in 750W, 650W and 550W models.  The Hydro branding comes from the fluid dynamic bearings in the 135mm fan which they have optimized for quiet operation.

Hydro PTM-750W_002.jpg

The 750W model has a pair of 4+4 power plugs for X299 users, the other two models will not though all will use ribbon cables to help you with cable management.  Internally you will find Japanese industrial grade electrolytic caps and a single 12V rail which will provide higher quality power than multiple rail designs.   All models will come with a 10 year warranty.

PR below the fold.

Source: FSP Group

NZXT Kraken X62, X52 and X61 compatible with AMD Ryzen Threadripper

Subject: Cases and Cooling | July 31, 2017 - 01:49 PM |
Tagged: nzxt, kraken, Kraken X62, Kraken X52, Kraken X61, Threadripper, amd

NZXT has announced that their three popular AiO watercoolers, the Kraken X62, Kraken X52, and Kraken X61 will be compatible with Threadripper, arriving soon to retailers.   

unnamed.png

NZXT has been working with AMD and created an adapter for SocketTR4 to allow you to use their cooler in your new system.  The retention clip will be supplied by AMD, in the package the new CPUs.  This is a good thing, considering the unique new way in which you install Threadripper processors.  If you haven't seen the video demonstrating the installation process you can see it below.

 

Source: NZXT

Build your own watercooling loop with the EKWB L360 2.0 Kit

Subject: Cases and Cooling | July 24, 2017 - 02:34 PM |
Tagged: watercooler, EKWB, EK-KIT

EKWB's L360 2.0 Kit is a ~$250 pre-compiled watercooling kit which includes a EK-Supremacy MX waterblock, EK-CoolStream PE 360mm radiator with three EK-Vardar F3-120mm fans, EK-XRES 100 DDC MX 3.1 PWM pump and reservoir, 2m of tubing plus compression fittings and a container of EK-Ekoolant EVO Clear coolant concentrate, good for 1l of coolant once diluted. All you need to do is assemble the kit and install it in your system.  Modders-Inc did just that, the installation process was enjoyable and far more effective than air cooling.  If you did plan to add in a GPU waterblock EKWB recommends adding in another radiator which should make your cooling even more effective. 

Check out the full review here.

ek_img_md00031.jpg

"EKWB has been in watercooling since its meager beginnings in 1999. Every package, every kit, every block advancing the genre of watercooling. As the critical mass for watercooling began to grow, and the knowledge barrier for putting these kits into your system began to fall, companies have been putting together pre-compiled kits of components to make it easier on the …"

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: Modders Inc

CRYORIG's A40; two heads are better than one?

Subject: Cases and Cooling | July 21, 2017 - 03:49 PM |
Tagged: CRYORIG, CRYORIG A40, AIO, water cooler

The CRYORIG A40 is not a new cooler but its unique design is worth revisiting for those who have forgotten about its existence.  Instead of having a single area in which to dump heat, the pump assembly mounted to the CPU also has its own fan.  That fan did not not noticeably decrease the CPU temperatures when TechPowerUp tested it, however for SFF systems and other builds with components which could benefit from airflow inside the case that fan is more than just a gimmick.  Check out the full review here.

title.jpg

"The A40 by CRYORIG is the company's entry level offering in their all-in-one hybrid liquid CPU cooler lineup. It lacks the size of the A80 and the radiator thickness of the A40 Ultimate. However, unlike the others, it offers a more affordable price point with all the same features."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: TechPowerUp

Thermaltake's $25 Contac Silent 12 heatsink for Ryzen

Subject: Cases and Cooling | July 14, 2017 - 03:15 PM |
Tagged: thermaltake, Contac Silent 12, ryzen, AM4, amd, heatsink, air cooler

Thermaltake has a new cooler for those planning a Ryzen build on a budget, or for quiet system builds.  The Contac Silent 12 is a mere 153x12x100.3mm in size, with the fan attached, and weighs a paltry 700g however it is capable of almost matching the performance of AMD's Wraith cooler while operating at a noticeably quieter level.  In addition to the heatsink you will find a 'low-noise cable' which changes the fans RPM span from 500-1500 RPM to 400-1100 RPM however in their tests The Tech Report found it had little effect on the noise produced by a system under load.  See the full results here.

tower.jpg

"Thermaltake's Contac Silent 12 relies on an established design and a simple mounting system to get AMD Socket AM4 builders up and running as quickly as possible. We tested this cooler at stock and overclocked speeds to see how it stacks up for just $25."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

MSI gets into the CPU heatsink business big time, the Core Frozr XL

Subject: Cases and Cooling | July 5, 2017 - 03:38 PM |
Tagged: ryzen, msi, Core Frozr XL

The MSI Core Frozr XL is not the first CPU heatsink to come out of that company but it is the largest, 150.4x170.0x129.8mm in size and a hair short of 2kg with the included fans.  The fancy plastic shrouds over the fans also act as the mounting point for the fans and can be adjusted to provide a little more clearance for tall DIMMs though it is still going to be a tight squeeze.  As the cooler is designed for AMD's new Ryzen chips, as well as some legacy chips, Neoseeker tested it against AMD's Wraith cooler and the AiO Ryzen cooler.  The MSI heatsink did much better at load, however when the system was idle the bundled coolers were a little better; though how often is your system on and idling anyways? 

Check out this RGBeast here.

Capture.PNG

"The totally massive MSI Core Frozr XL benefits from a large nickel-plated copper thermal plate to quickly pull the heat away from the CPU. The heat then transfers from the thermal baseplate into the eight 6mm SuperPipes, which move the heat upward to the large aluminum dissipation fin array that can dissipate up to 250W of heat. Lastly, the two MSI 120mm Torx fans push-pull the heat away from all of that thermal mass and out of the computer case."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

Source: Neoseeker

Gamers Nexus Talks Mining with AIB and PSU Vendors

Subject: Graphics Cards, Cases and Cooling | July 5, 2017 - 07:01 AM |
Tagged: supply shortage, shortage, ethereum, cryptocurrency

The cryptocurrency craze is kind-of like the old gold rush. Tokens are just out there waiting to be discovered, and value is applied when people trade it in exchange for goods and services. In this case, these tokens are discovered by doing math, and faster computers acquire more, and the algorithm is quite parallel. Some of the non-Bitcoin currencies are gaining traction, and becoming economically viable to mind with off-the-shelf parts, so gaming parts are being sold out... and not to gamers.

What do the video card add-in board (AIB) partners (as in the companies that take GPUs from NVIDIA and AMD and attach them to things that will actually plug into a motherboard) think of this? Gamers Nexus reached out to a bunch of them and, off the record, got a bunch of responses. The fifteen-minute video is quite interesting, and covers a lot of issues like brand loyalty, the second-hand market flooding, and RMA abuse. It even talks about the abnormal stress the GPU mining could have on power supplies. Most of the responses make sense, but it’s interesting to hear it coming from people in the industry, even if “who specifically said what” has been anonymized.

Of course, this is for the best, because you'll get more candid responses that way.

Seasonic's PRIME series of PSUs goes Platinum

Subject: Cases and Cooling | June 26, 2017 - 06:32 PM |
Tagged: Seasonic PRIME, 850W, 80 Plus Platinum, modular psu

It was almost a year ago that Lee reviewed the Seasonic PRIME 750W Titanium PSU; today it is [H]ard|OCP who has a review of a cousin of that PSU.  The Seasonic PRIME 850W Platinum PSU is a new addition to the PRIME family, bearing the same 12 year warranty as its relatives as well as the single 12V rail design and physical Hybrid button.  As [H] have already reviewed the previous 850W PRIME model, the newcomer has some big shoes to fill.  It comes very close to doing so, as you can see in their full review.

1496794935dtrk6eag20_2_9_l.jpg

"As is usual, Seasonic talks softly and carries a big stick. The biggest stick lately has been its Prime series power supplies. Today's Prime comes to us touting excellent efficiency, a fully modular design, tight output voltage, and a quiet noise profile supplied by a fluid dynamic bearing fan. Does Seasonic continue its current reign?"

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

Source: [H]ard|OCP

FSP embraces summer with new heatsinks like the Windale 6

Subject: Cases and Cooling | June 22, 2017 - 03:06 PM |
Tagged: FSP Group, windale 6

FSP Group are more commonly known for their PSUs, recently they have branched out into other components including heatsinks.  [H]ard|OCP had a chance to test out their Windale 6 cooler, which sounds oddly familiar.  The cooling performance was somewhat better than a stock cooler and noticeably quieter, but overclockers may want to look elsewhere.  The cooler stands 122x110x160mm and sports a 120mm fan however the mounting solution presented some challenges.  Drop by for the details.

1497486913ql8e7l7hj5_2_7_l.jpg

"FSP is a very new brand when it comes to CPU air coolers and is entering a market that is highly competitive and seeded with others that have been designing air coolers for quite some time. Its Windale 6 cooler features six direct contact heatpipes, a 120mm fan, and what FSP says is an "optimized fin design." But does it cool?"

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: [H]ard|OCP

Corsair's Crystal Series 570X, show off your temper

Subject: Cases and Cooling | June 15, 2017 - 01:34 PM |
Tagged: tempered glass, corsair, Crystal Series, 570x

It has been quite a while since Sebastian reviewed Corsair's Crystal Series 570X tempered glass case; so why not take another look?  Over at Techgage you can revist this case with a view.  They were impressed by the cooling included, three fans and a pre-installed fan hub for three more RGB fans as well as the air filter placements which help keep dust out of the case.  There is no equivalent feature to get fingerprints off of the glass front and sides so you will spend some time cleaning up your case.  Then again, if you are choosing a transparent enclosure, you likely spend a lot of time ensuring all your components are looking their best.

Corsair-Crystal-570X-Chassis-Final-Build-Turned-On.jpg

"Corsair’s Crystal series is named as such because of its use of tempered glass, and as the top dog in the current lineup, the 570X sports that tempered glass on all four sides. Despite its delicate frame, the chassis proved great to build with, and as we found out, its beautiful aesthetics don’t hurt its cooling efficiency."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: Techgage

Run softly and carry a big Scythe

Subject: Cases and Cooling | June 6, 2017 - 12:39 PM |
Tagged: scythe, Mugen 5, air cooler

Scythe's Mugen 5 has a bit of a list to one side, which is designed to give your RAM a little more breathing room and will fit on motherboards with very little clearance between the socket and the DIMMs.  At 890g and 130x110x154.5mm it is not the largest cooler on the market but is big enough to warrant attention when picking out a case to install your system in.  [H]ard|OCP's tests show this cooler to be more focused the audibility of the cooler than topping the cooling charts, heavy overclockers will be better served by a different cooler but those building a quiet system should check out the full review.

149591671380fntpns12_2_6_l.jpg

"The Mugen 5 is one of the larger CPU air coolers you will find on the market, and with that is has an "asymmetric design for maximum memory compatibility," so it does not extend deep into DIMM territory. The polished copper baseplate, as well as the rest of the HSF is nickel plated. Also we have a newly engineered mounting mechanism."

Here is some more Tech News from around the web:

Tech Talk

Source: [H]ard|OCP

Computex 2017: Phanteks Puts the Tower in Tower Style Cases With SFF Evolv Shift and Shift X

Subject: Cases and Cooling | June 4, 2017 - 11:04 AM |
Tagged: water cooling, SFX-L, SFF, phanteks, mini ITX, htpc, evolv shift x, evolv shift

Phanteks Project 217 prototype case is finally official and will be known as the Evolv Shift and Evolv Shift X. Both are small form factor cases that feature a unique tower design that has the approximate footprint of a large graphics card, but manages to fit quite a bit of hardware inside by building up rather than out. The skyscraper style cases measure 6.7” wide and 10.63” deep. The Evplv Shift is the shorter of the two at 18.9” tall while the Evolv Shift X is 25.9”. The Mini ITX cases are constructed from a powder coated steel frame, aluminum cover panels, and tempered glass side panels.

Phanteks Evolv Shift and Evolv Shift X.png

HardwareCanucks shot video of the new SFF cases!

The Evolv Shift and Shift X both have black aluminum insides and a silver aluminum front panel. There are fam vents around the edges of the front panel and two USB 3.0 ports tucked away on the side. The top of the case covers the motherboard I/O and has a cutout in the back for routing the I/O cables out of the case - on the Shift X this piece is also aluminum but on the Shift it is plastic to cut costs. The two tempered glass side panels and front and back panels are held on by thumbscrews to allow for easy removal to work on the build. Being able to take all four sides off should make to easier to build in the small space.

Other case features include removable case feet that enables you to lay the case horizontally on one of its two sides (so you can show off the CPU side or GPU side), dust filters up front, and separation of the two front fans and compartments so that one can be an intake and the other exhaust if you wish. For such a small case there is quite a njt of cable management going o with rubber grommets and horizontal cable tracks (with a magnetic door for easy access) to hid away your cables and pass them from the PSU compartment to the motherboard compartment). Interestingly the GPU is mounted vertically and the bracket can be rotated and adjusted left and right so that you can choose to see the back of the graphics card or (finally!!) the front of the card with the artwork -- that’s right a case that lets you see and show off the stickers and cooler of your graphics card! (hehe, it has always irked me they put the artwork on the part of thr GPU you usually never see once it's in the case.)

Internally, the case is divided into two main areas with the power supply on bottom along with room for water cooling pumps and reservoirs and the motherboard, processor, and graphics cards stacked on top of the PSU area. The Evolv Shift and Evolv Shift X both support small form factor power supplies (SFX and SFX-L), Mini ITX motherboards, and even large graphics card thanks to the riser cable and vertical mounting. The larger Shift X can also hold ATX PSUs with the caveat that you have to give up the PSU shroud.

Cooling support includes air and water coolers with up to three 120mm or 140mm fans up front and one 120mm or 140mm fan in the bottom. The case will come with two 140mm fans out of the box.

As far as storage is concerned the case had room for two 2.5” drives and either one 3.5” drive on the Shift or two 3.5” drives on the Shift X.

Oh, and there is also an included RGB controller if you want to add a bit of bling to your dual windowed skyscraper PC.

The Evolv Shift and Evolv Shift X are coming later this year for $110 and $160 respectively.

These look to be very unique cases that will look good on a desk or even in the living room as a home theater PC. I am looking forward to the reviews on these as I am curious how well the case can keep high end components cool and how easy they are to build a system in.

Computex 2017: BitFenix Shows Off Affordable Mid-Tower With RGB and Tempered Glass

Subject: Cases and Cooling | June 3, 2017 - 11:16 PM |
Tagged: computex, bitfenix, mid tower, E-ATX Case, RGB LED, gaming, tempered glass

BitFenix had several new PC cases on display at its Computex booth, but the one that caught my eye was the sub-$100 Enso mid-tower that has some premium features including a large tempered glass side panel, RGB LED and fan controllers, removable filters, and various cable management features. The BitFenix Enso has a clean design that out of the box limits the RGB to a nice looking front panel while allowing enthusiasts to go crazy with aftermarket LED strips and LED fans if they wish.

BitFenix Enso Mid-Tower.jpg

The BitFenix Enso mid-tower (Image credit: KitGuru)

The new Enso chassis measures 8.2" x 19.2" x 14.4" (209 x 487 x 442mm).and is clad in all black with clean lines and edges that strikes a balance between boxy and gaudy (heh). The front is a smooth panel that slightly angles out (no external drive support here) with RGB LEDs in all four corners. The front I/O is up top with two USB 3.0, two audio, and power and reset buttons. The left side is almost entirely comprised of a tempered glass side panel that is held on by black thumbscrews.

The top has a mesh grill with support for two 120mm fans along with a removable magnetic fan filter. There is also room for a 120mm fan in the back and two 120mm fans up front (where there is also a removable filter that pulls out from the left side of the front panel). There is not enough room up top for a water cooling radiator up top, but there is plenty of room for up to a 240mm radiator in the front.

The bottom of the case has a compartment for the bottom mounted up to 220mm power supply (which also has a removable dust filter) and two 3.5” drives along with space to hide excess cables. This area is covered by a simple black shroud that should make cable management easier.

Dropping support for external drive bays and extra 3.5” bays, BitFenix is able to support E-ATX motherboards, long graphics cards (up to 320mm, their demo used an Asus Strix GTX 1080), and water cooling radiators in a compact mid-tower case. BitFenix states it is possible to mount a 360mm radiator in the front, but it the specifications suggest if you would be limited to two fans with matching vents.

BitFenix Enso Motherboard Tray.png

Lots of tie downs and space to hide cables! (Image credit: Bitwit Kyle)

The right side panel is blank, and removing it reveals the back of the motherboard tray. There is room for three 2.5” SSDs with one behind the motherboard and two behind the front fans. The motherboard tray has a large CPU cutout, lots of spots to tie up cables, and rubber grommets for passing cables through to the motherboard and graphics card. Having move of the components sitting behind the motherboard tray means that making a clean looking build will be a bit easier (no drive power cables to hide).

The front panel RGB LEDs are “addressable” which is to say that they can be controlled via the controller at the back or via software where BitFenix is working with Asus to allow its RGB LEDs to be controlled with its Aurora software. There is also a fan controller that looks to accept PWM and control 3-pin fans from that signal. The case is also compatible with LED fans and LEDs strips (the BitFenix demo used strips from Asus that could be controlled with the Asus software). As far as the front panel, you can choose a color or activate a gentle pulsing color change mode that cycles through the colors of the rainbow.

BitFenix Enso Showcase.png

(Image credit: Bitwit Kyle)

Out of the box, the BitFenix Enso will have the front panel LEDs and controllers, but users will need to purchase fans and/or LED strips separately. This is not necessarily bad news though because it allows enthusiasts to pick the fans and LEDs they want (or don’t want), and it also allows the case to hit the budget sub-$100 market with lots of nice DIY-friendly features.

According to a BitFenix representative, the BitFenix Enso will arrive around the end of Q3 2017 or towards the beginning of Q4 with an MSRP of $79.

It looks like an impressive budget case, and if they can hit that $79 target it should be a great value that will let you show off your DIY build without breaking the bank! From the videos at Computex, I am really liking the design as well. What are your thoughts?

Source: Tech City

Computex 2017: Lian-Li Launching AIO Liquid Coolers With Raw Copper Radiators

Subject: Cases and Cooling | June 3, 2017 - 06:01 PM |
Tagged: water cooling, Lian-Li, LCS, copper radiator, copper, computex, cinsys, AIO

Guru3D made an interesting find at Lian-Li's Computex booth this year where they managed to take photos of a new all in one (AIO) liquid cooler that sports an all copper loop. Specifically, the company was showing off a new Lian-Li branded liquid cooler from Cinsys with a 240mm radiator. The "X-R240 Expandable water cooling heat radiating system" features a raw copper radiator surrounded by a metal shroud (reportedly aluminum) that houses 120mm fan mounts and a pump, large removable tubing, and a thin nickel plated copper CPU water block.

Lian-Li 240mm AIO Copper Cooler.jpg

Lian-Li X-R240 expandable water cooler. (Image credit: Guru3D)

Looking at the photos from Guru3D, the Lian-Li X-R240 AIO certainly looks classy and should perform fairly well with the copper block and copper radiator (which is nice to see in an AIO where aluminum is common). The large tubing appears to be fairly long enabling the radiator to be placed up to or in the front of a mid-tower case, though I am curious how flexible it will be in a smaller case in tight quarters (if I am remembering my watercooling correctly, the larger diameter should mean it will be less likely to kink though). Further, it looks like the tubing is removable and users will be able to expand the loop to add additional blocks and/or radiators which is nice though you should be careful to avoid adding non-copper (aluminum/silver/ect) components to the Lian-Li loop. Angled and/or swivel barbs on the CPU blocks would have been nice as well since the straight barbs on the thin CPU block could make installation more difficult.

The raw copper is a nice aesthetic touch, though once it is installed in your case and sitting behind fans it is going to be hard to see and Guru3D does note that over time the copper will oxidize and discolor. Still, it might be useful for modders to get that steam punk look and feel. Thankfully it looks like there is plastic (and maybe foam) separating the copper radiator from the aluminum shell/shroud though it's less of an issue since the outside of the radiator isn't going to be submerged in water (hopefully!).

The company will reportedly be releasing other models beyond the 240mm shown at Computex presumably by the same OEM (Cinsys). A 360mm radiator and some GPU blocks would be nice to see! Hopefully Morry or Sebastian can get one in for testing soon!

What are your thoughts on Lian-Li using raw copper? Do you prefer plated copper?

Source: Guru3D

Computex 2017: Be Quiet Launches Two SFX-L Power Supplies

Subject: Cases and Cooling | June 1, 2017 - 10:38 PM |
Tagged: SFX-L, SFF, High Power, computex, be quiet!, 80+ gold

German PSU maker be quiet! Had several new power supplies on display at Computex. Perhaps the most interesting for small form factor enthusiasts are the two new SFX-L power supplies. The aptly named SFX-L-500W and SFX-L-600W are fully modular 80+ Gold rated power supplies that are not much bigger than the 120mm temperature controlled fan that cools it.

be-quiet-SFX-L-600W-Computex-2017-2.jpg

SFFNetwork examined the new PSUs at Computex.

According to AnandTech, be quiet! Is using High Power as the OEM for these power supplies rather than its usual partner FSP. The High Power platform offers up a single 12V rail design that supports multi GPU setups with the inclusion of 4 PCI-E power connectors. At least on the 600W variant (not sure on the 500W) the PSU is rated at 50A on the 12-volt rail, which is nice to see. The fan does not support spinning down to zero when under light load, but it does spin down to lower RPMs and has a temperature controlled fan curve that be quiet! claims is sufficient for even noise sensitive applications like HTPCs (hopefully Lee gets his hands on these soon and can confirm the advertised specs).

Both of the new small form factor (SFF) power supplies come with a three-year warranty which seems to be pretty standard for power supplies these days though five would be nice to see especially when they are going to be going into tiny cases with less airflow than the traditional ATX desktop. Speaking of ATX, the SFX-L PSUs come with an adapter that will allow you to install the SFF unit into a standard ATX power supply mount should you want to use it in a larger case.

The 500W and 600W PSUs have US MSRPs of $109 and $129 respectively.                                  

Source: SFF Network

Thermaltake's Smart Pro RGB PSU series can provide you with the good kind of lightshow

Subject: Cases and Cooling | May 29, 2017 - 05:57 PM |
Tagged: thermaltake, Smart Pro RGB, 850W, modular psu

The Smart portion of the Thermaltake Smart Pro RGB seems to refer to the Riing 14 RGB fan that can produce up to 256 colours with five different lighting modes to choose from, and built-in memory to save your light shows. [H]ard|OCP turned the RGB off immediately, then proceeded to test the power the PSU provides, as you would expect.  The PSU passed all the tests, but not with flying colours, as some performance measures such as voltage regulation did not match the competitions.  On the other hand, if you need RGBs on your PSU then Thermaltake's Smart Pro RGB models are worth your consideration.

1494980196z9k8jyq5nt_2_8_l.jpg

"Frag-harder RGB lighting is all the rage, and so of course we are now seeing those in PSUs too. Thermaltake has a healthy 850 watt PSU here for review today that actually hits the sub-$100 mark by 1 cent. Fully modular with great DC output; is there anything not to like? You can turn the RGB off. And a 7 year warranty."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

Source: [H]ard|OCP

BitFenix Shogun, a well rounded case

Subject: Cases and Cooling | May 29, 2017 - 04:21 PM |
Tagged: bitfenix, Shogun

BitFenix's Shogun case stands 250x565x525mm in size and allows coolers of up to 175mm in height and GPUs of up to 410mm.  It is not the largest case on the market but it is certainly no SFF enclosure, fitting E-ATX motherboards though the tray has mounting points for even mini-ITX if you have a strange idea in mind.  The front panel is subtly hidden in the gap between the front bezel and the cases top with enough of a gap you should not have any issues fitting a thumb drive in.  Bitfenix gave this metal and glass case high marks for functionality, even if they weren't personally in love with the overall aesthetics.

caseunpacked.jpg

"The Bitfenix Shogun may not look the part when it comes to its naming, but it does offer a nice and mostly functional feature set coupled with great overall build quality. It also sets itself apart by allowing the user to expand the motherboard tray for an E-ATX board."

Here are some more Cases & Cooling reviews from around the web:

CASES & COOLING

 

Source: TechPowerUp

Computex 2017: RIOTORO Announces CR500 Tempered Glass, CR1288 Prism RGB Full-Tower, and CR1088 Mini-Tower Cases

Subject: Cases and Cooling | May 29, 2017 - 01:27 AM |
Tagged: riotoro, RGB

We first heard about RIOTORO at the CES before last, where they launched their CR1280 Prism case with its RGB lighting. They’ve since added quite a few models across different product segments.

Now, at Computex, they’re introducing three new models: the CR1288, the CR1088, and the CR500. The first two build upon existing products, while the last occupies a new segment for the company.

I’ll start with the CR1288 Prism, which fills a similar role as their aforementioned CR1280 Prism. It’s unclear whether this will replace that case, or whether they will both co-exist. Either way, RIOTORO claims that it has better cooling, noise reduction, and access for installation than its predecessor. It also looks quite different from the front, with a big, vertical stripe up the center of that side. It retains the CR1280 Prism’s front panel controls.

riotoro-2017-computex-cr1288prism.png

The CR1288 Prism Full-Tower

The CR1288 Prism is listed as a Q3 launch with a $159.99 USD expected street price.

Next is the CR1088 “Ultra-Compact Tower Case”. Like the CR1288, this is a redesign of the CR1080, although it’s unclear whether they will co-exist. This case is a little larger than a cubic foot, 15.7” long x 9” wide x 14.1” high, but supports a full-sized ATX motherboards and graphics cards. The design routes air across the typical hot spots, and it separates the power supply and drives (2x 3.5” and 3x 2.5”) into its own compartment, with cable routing for cable management.

riotoro-2017-computex-cr1088.png

The CR1088 Mini-Tower

The CR1088 is listed as a Q3 launch with an $89.99 USD expected street price.

Last is the CR500, which definitely does not replace any existing model. This is a lower-cost mid-tower with a tempered glass window, a separate compartment (which I’m guessing is for the power supply and drives, like the CR1288), and tool-free installation (with cable management). It’s made out of steel, and can mount up to a 240mm radiator.

riotoro-2017-computex-cr500.png

The CR500 Mid-Tower

The CR500 is listed as a Q3 launch with a $79.99 USD expected street price. RIOTORO says that it will have a $69.99 USD introductory price, but it’s unclear what that means (ex: if it’s a pre-order, and from who).

Source: RIOTORO