Subject: Graphics Cards | October 6, 2016 - 03:17 PM | Tim Verry
Tagged: windforce, pascal, nvidia, GTX 1080, gigabyte
Gigabyte is launching a new graphics card with a blower style cooler that it is calling the GTX 1080 TT. The card, which is likely based on the NVIDIA reference PCB, uses a lateral-blower style single “WindForce Turbo Fan” fan. The orange and black shrouded fan takes design cues from the company’s higher end Xtreme Gaming cards and it has a very Mass Effect / Halo Forerunners vibe to it.
The GV-N1080TTOC-8GD is powered by a single 8-pin PCI-E power connector and has a 180W TDP. Despite not using more than one external power connector, the card does still have a bit of overclocking headroom (a total of 225W from the PCI-E spec, though overdrawing on the 8-pin has been done before if the card is not locked in the BIOS to not do so heh). External video outputs include one DVI, one HDMI, and three DisplayPorts. I wish that the DVI port had been cut so that the blower cooler could have a much larger vent to exhaust air out of the case with, but it is what it is.
Out of the box the Gigabyte GTX 1080 TT runs the Pascal-based 2560 CUDA core GPU at 1632 MHz base and 1772 MHz boost. In OC Mode the GPU runs at 1657 MHz base and 1797 MHz boost. The 8 GB of GDDR5X memory is left untouched at the stock 10 GHz in either case. For comparison, reference clock speeds are 1607 MHz base and 1733 MHz boost. As far as factory overclocks go, these are not bad (they are usually at least this conservative).
The heatsink uses three direct contact 6mm copper heat pipes for the GPU and aluminum plates on the VRM and memory chips that transfer heat to an aluminum fin channels that the blower fan at the back of the card uses to push case air over and out of the case. It may be possible to push the card beyond the OC mode clocks though it is not clear how stable boost clocks will be under load (or how loud the fan will be). We will have to wait for reviews on that. If you have a cramped case this may be a decent GTX 1080 option that is cheaper than the Founder's Edition desgin.
There is no word on pricing or an exact release date yet, but I would estimate it at around $640 at launch.
Subject: Graphics Cards | July 26, 2016 - 12:36 AM | Tim Verry
Tagged: windforce, pascal, gigabyte, GeForce GTX 1060
In a recent press release, Gigabyte announced that it will soon be adding four new GTX 1060 graphics cards to its lineup. The new cards feature Windforce series coolers and custom PCBs. At the high end is the GTX 1060 G1 Gaming followed by the GTX 1060 Windforce OC, small form factor friendly GTX 1060 Mini ITX OC, and the budget minded GTX 1060 D5. While the company has yet to divulge pricing or availability, the cards should be out within the next month or two.
All of the upcoming cards use a custom design that uses a custom PCB and power phase setup paired with Gigabyte's dual – or in the case of the Mini ITX card – single fan Windforce air cooler. Unfortunately, exact specifications for all of the cards except the high end model are unknown including core and memory clocks. The coolers use a dual composite heatpipe that directly touches the GPU to pull heat away and is dissipated by an aluminum fin stack. The fans are 90mm on all of the cards with the dual fan models using a design that has each fan spinning alternate directions of the other. The cards feature 6GB of GDDR5 memory as well as DVI, HDMI, and DisplayPort video outputs. For example, the Mini ITX OC graphics card (which is only 17cm long) and features two DVI, one HDMI, and one DP output.
More information is available on the GTX 1060 G1 Gaming. This card is a dual slot dual fan design with a 6+1 power phase (reference is 3+1) powered by a single 8-pin power connector. The fans are shrouded and there is a metal backplate to aid in stability and cooling. Gigabyte claims that its "GPU Gauntlet" technology ensures users get heavily overclockable chips thanks to sorting and using the most promising chips.
The 16nm Pascal GPU is factory overclocked to 1847 MHz boost and 1620 MHz base clockspeeds in OC mode and 1809 MHz boost and 1594 MHz base in gaming mode. Users will be able to use the company's Xtreme Engine software to dial up the overclocks further as well as mess with the RGB LEDs. For comparison, the reference clockspeeds are 1708 MHz boost and 1506 MHz base. Gigabyte has left the 6GB of GDDR5 memory untouched at 8008 MHz.
The other cards should have similarly decent factory overclocks, but it is hard to say exactly what they will be out of the box. While I am not a big fan of the aesthetics, the Windforce coolers should let users push Pascal fairly far (for air cooling).
I would guess that the Gigabyte GTX 1060 G1 Gaming will MSRP for just above $300 while the lower end cards will be around $260 (the Mini ITX OC may be at a slight premium above that).
What do you think about Gigabyte's new cards?
Subject: Graphics Cards | February 20, 2015 - 02:08 PM | Jeremy Hellstrom
Tagged: gigabyte, nvidia, GTX 980 G1 GAMING, windforce, maxwell, factory overclocked
If you want the same amount of Maxwell Streaming Multiprocessors and ROP units as a GTX 980 as well as that last 500MB of RAM to run at full speed then you will need to pay for a GTX 980. One choice is Gigabyte's GTX 980 G1 Gaming which will cost you $580, around $240 more than a GTX 970 but the premium can be worth it if you need the power. [H]ard|OCP took the already overclocked card from a boost GPU frequency of 1329MHz and RAM of 7GHz all the way to a boost of 1513MHz with RAM topping out at 8.11GHz. That overclock had a noticeable effect on performance and helped the card garner an Editors Choice award. See it in action here.
"Today we have the GIGABYTE GTX 980 G1 GAMING, which features the WINDFORCE 600W cooling system and a high factory overclock. We will make comparisons to the competition, find out how fast it is compared to a GTX 980, and you won't believe the overclock we achieved! We will make both performance and price comparisons."
Here are some more Graphics Card articles from around the web:
- ASUS GTX 980 Matrix 4 GB @ techPowerUp
- OcUK GTX 970 @ HardwareHeaven
- Palit GTX960 Super JetStream @ Kitguru
- PowerColor PCS+ R9 290X 8GB Review @ TechwareLabs
- Sapphire Vapor-X R9 290x 8GB Tri-X Video Card @ Modders-Inc
Subject: Graphics Cards, Shows and Expos | January 9, 2014 - 06:05 PM | Ryan Shrout
Tagged: CES, CES 2014, gigabyte, R9 290X, gtx 780 ti, windforce
While the world still waits for stock of the custom cooled R9 290X and R9 290 cards from AMD's partners to show up in stores, Gigabyte was showcasing its WindForce models on the floor at CES 2014.
The Gigabyte GV-R929XOC-4GD is an R9 290X graphics cards that includes the company custom designed WindForce, triple fan cooler. The cooler is rated at 450 watts of dissipation, but hopefully you'll never actually be drawing that from this single GPU graphics card. The core clock on this model will be slightly overclocked, going from the stock 1000 MHz to 1040 MHz. Hopefully we'll have a review sample soon so we can verify that it maintains that overclocked clock speed throughout the gaming workloads.
Using the very same cooler is the GV-N78TGHZ-3GD based on the GeForce GTX 780 Ti GPU. In fact, without my tell you which card was which, you'd likely have no way to tell them apart without looking at the PCB more closely. Gigabyte will be setting the base clock on this model at 1085 MHz and the Boost clock at 1150 MHz.
The cards will also include a back plate on the rear of the PCB to help protect the components and ICs while also strengthening the board during shipping general use. Gigabyte says these cards will only carry and MSRP that is $20-50 more than the reference cards so look for each of them this month!
Follow all of our coverage of the show at http://pcper.com/ces!
Computex 2013: Gigabyte Preparing Custom GTX Titan With WindForce 450W Cooler... Some Assembly Required
Subject: Graphics Cards | June 7, 2013 - 01:20 PM | Tim Verry
Tagged: windforce 450w, windforce, gtx titan, gk110, gigabyte
Back in April, Gigabyte showed off its new custom WindForce 450W GPU HSF, but did not name which specific high end graphics cards it would be used with. So far, NVIDIA's highest-end single GPU solution, the GTX Titan, has been off limits for GPU manufacturers as far as putting custom air coolers on the cards (NVIDIA has restricted designs to its reference cooler or factory installed water blocks).
It seems that Gigabyte has found a solution to the cooler restriction, however. The company will be selling a GTX TITAN with model number GV-NTITAN-6GDB later this year that will come with NVIDIA's reference cooler pre-installed along with a bundled WindForce 3X 450W cooler and instructions for switching out the coolers.
Gigabyte Is Showing Off the custom GTX Titan at Computex, as discovered by TechPowerUp.
Users that do take Gigabyte up on its offer to switch to the custom WindForce cooler will still be covered under the company's standard warranty policy, which is a good thing. The kit is likely to be more expensive than your standard TITAN though as Gigabyte is having to sell the card with two coolers and increased support costs. On the other hand, users could swap out the coolers and then sell the unused TITAN reference cooler to offset some of the cost of the kit.
Gigabyte is actually showing off the new graphics card with WindForce 3X 450W cooler at Computex this week. The dual slot WindForce cooler is said to keep a GTX 680 2°C and 23.3 dB quieter than the reference cooler when running the Furmark benchmark suite. The major benefit of the WindForce is having three large fans that can spin at lower RPMs to give you the same cooling performance as the reference NVIDIA design at a much lower noise volume rather than pure cooling performance. Should you be looking to push the TITAN to the extreme, a water block would be your best bet, but for many users i think the allure of a quieter air cooled TITAN may be enough for Gigabyte to snag a few adventurous enthusiasts willing to put up with assembling the new card themselves.
More information on the WindForce 3X 450W cooler can be found here.
Subject: Graphics Cards | April 14, 2013 - 07:59 PM | Tim Verry
Tagged: windforce, nvidia, gtx titan, gtx 680, gpu cooler, gigabyte
Earlier this week, PC component manufacturer Gigabyte showed off its new graphics card cooler at its New Idea Tech Tour even in Berlin, Germany. The new triple slot cooler is built for this generation's highest-end graphics cards. It is capable of cooling cards with up to 450W TDPs while keeping the cards cooler and quiter than reference heatsinks.
The Gigabyte WindForce 450W cooler is a triple slot design that combines a large heatsink with three 80mm fans. The heatsink features two aluminum fin arrays connected to the GPU block by three 10mm copper heatpipes. Gigabyte stated during the card's reveal that its cooler keeps a NVIDIA GTX 680 graphics card 2°C cooler and 23.3 dB quiter during a Furmark benchmark run. Further, the cooler will allow these high end cards, like the GTX Titan to achieve higher (stable) boost clocks.
ComputerBase.de was on hand at Gigabyte's event in Berlin to snap shots of the upcoming GPU cooler.
The company has not announced which graphics cards will use the new cooler or when it will be available, but A Gigabyte GTX 680 and a custom cooled-Titan seem to be likely candidates considering these cards were mentioned in the examples given in the presentation. Note that NVIDIA has prohibited AIB partners from putting custom coolers on the Titan thus far, but other rumored Titan graphics cards with custom coolers seem to suggest that the company will allow custom-cooled Titans to be sold at retail at some point. In addition to using it for the top-end NVIDIA cards, I think a GTX 670 or GTX 660 Ti GPU using this cooler would also be great, as it would likely be one of the quieter running options available (because you could spin the three 80mm fans much slower than the single reference fan and still get the same temps).
What do you think about Gigabyte's new 450W GPU cooler? You can find more photos over at Computer Base (computerbase.de).
Subject: Graphics Cards | April 5, 2012 - 11:19 PM | Tim Verry
Tagged: windforce, overclock, nvidia, gtx 680, gpu, gigabyte, custom gtx 680
Popular motherboard manufacturer Gigabyte is the latest company to debut a custom version of the NVIDIA GTX 680 reference graphics card. Gigabyte’s unique take on the GTX 680 starts off with a custom dark blue PCB and ripping out the puny two six pin PCI-E power connectors. They are then replaced with one eight pin and one six pin PCI-E power connector. Then, they top it off with a custom three fan cooler. The heatsink uses three copper heatpipes with direct contact with the GPU, and two arrays of aluminum fins.
The cooler and blue PCB via VR-Zone
The extra power provided by the eight pin PCI-E connector allows for potentially higher overclocks (depending on the particular chips), and the custom cooler keeps the overclocked card nice and cool. In fact, Gigabyte is shipping the card with a factory overclock. Although they did not overclock the 2 GB of GDDR5 memory from stock, they have set the base clock frequency and boost frequency at 1071 MHz and 1124 MHz boost respectively. Compared to the reference specs of 1006 MHz base and 1058 MHz boost, that amounts to a respectable 65 MHz base overclock and 66 MHz boost overclock out of the box. Further, depending on the chip, they may be capable of overclocking much higher.
The assembled card showing the video outputs via Guru3D
So long as you can find one in stock, the NVIDIA GTX 680 GPU is shaping up to be an interesting card, especially the custom versions! More photos of the previewed Gigabyte GTX 680 WindForce edition is available here and here.