Subject: General Tech | June 15, 2016 - 12:37 PM | Jeremy Hellstrom
Tagged: rx 470, amd, leak, RX 480M
Sharp eyes over at The Guru of 3D spotted some information in a recent press release from AMD that might have been unintentionally released; performance numbers and mention of a AMD Radeon RX 480M. These benchmarks are internal and so should be taken with a grain of salt but they do offer a glimpse at how the RX 470 will perform. The benchmarks were run on a system comprised of ab i7 5960X, 16GB memory and Radeon 16.20, showing better performance than a R9 270X on three games as well as Firestrike below. Follow the link for the results they gleaned from the footnotes.
"In the slide-deck that was released yesterday some benchmark numbers have been, well almost hidden. But they are there. I added them into two charts to check out.
Let me clearly state that the benchmarks have been performed by AMD so we cannot verify quality settings. The scores have been derived from the footnotes of the PDF"
Here is some more Tech News from around the web:
- The Terrible Devices Of The Internet Of Wrongs @ Hack a Day
- Virtualizing Around The FCC’s Firmware Modification Rules @ Hack a Day
- Graphene breakthrough could make chips a million times faster @ The Inquirer
- Apple's Safari browser will disable Flash by default in macOS @ The Inquirer
- Apple quietly launches next-gen encrypted file system @ The Register
Subject: Graphics Cards | April 22, 2016 - 10:16 AM | Sebastian Peak
Tagged: rumor, report, pascal, nvidia, leak, graphics card, gpu, gddr5x, GDDR5
According to a report from VideoCardz (via Overclock.net/Chip Hell) high quality images have leaked of the upcoming GP104 die, which is expected to power the GeForce GTX 1070 graphics card.
Image credit: VideoCardz.com
"This GP104-200 variant is supposedly planned for GeForce GTX 1070. Although it is a cut-down version of GP104-400, both GPUs will look exactly the same. The only difference being modified GPU configuration. The high quality picture is perfect material for comparison."
A couple of interesting things have emerged with this die shot, with the relatively small size of the GPU (die size estimated at 333 mm2), and the assumption that this will be using conventional GDDR5 memory - based on a previously leaked photo of the die on PCB.
Alleged photo of GP104 using GDDR5 memory (Image credit: VideoCardz via ChipHell)
"Leaker also says that GTX 1080 will feature GDDR5X memory, while GTX 1070 will stick to GDDR5 standard, both using 256-bit memory bus. Cards based on GP104 GPU are to be equipped with three DisplayPorts, HDMI and DVI."
While this is no doubt disappointing to those anticipating HBM with the upcoming Pascal consumer GPUs, the move isn't all that surprising considering the consistent rumors that GTX 1080 would use GDDR5X.
Is the lack of HBM (or HBM2) enough to make you skip this generation of GeForce GPU? This author points out that AMD's Fury X - the first GPU to use HBM - was still unable to beat a GTX 980 Ti in many tests, even though the 980 Ti uses conventional GDDR5. Memory is obviously important, but the core defines the performance of the GPU.
If NVIDIA has made improvements to performance and efficiency we should see impressive numbers, but this might be a more iterative update than originally expected - which only gives AMD more of a chance to win marketshare with their upcoming Radeon 400-series GPUs. It should be an interesting summer.
Subject: Graphics Cards | April 19, 2016 - 11:08 AM | Sebastian Peak
Tagged: rumor, report, nvidia, leak, GTX 1080, graphics card, gpu, geforce
Another reported photo of an upcoming GTX 1080 graphics card has appeared online, this time via a post on Baidu.
(Image credit: VR-Zone, via Baidu)
The image is typically low-resolution and features the slightly soft focus we've come to expect from alleged leaks. This doesn't mean it's not legitimate, and this isn't the first time we have seen this design. This image also appears to only be the cooler, without an actual graphics card board underneath.
We have reported on the upcoming GPU rumored to be named "GTX 1080" in the recent past, and while no official announcement has been made it seems safe to assume that a successor to the current 900-series GPUs is forthcoming.
Subject: General Tech | November 16, 2015 - 03:55 PM | Jeremy Hellstrom
Tagged: Skylake, LGA 1151, leak, kaby lake, intel 200, Intel, cannon lake
Benchlife.info got hold of two slides from an Intel presentation for Kaby Lake which cover some of the features you can expect to find on the new processor family. As with all leaks you should ensure you take a dosage of Sodium Chloride while looking through the information.
The Intel 200 chipset will provide up to 30 PCIe lanes, 24 of which can be dedicated to PCIe slots and another half dozen for SATA 6Gbps. The chipset can also manage up to 10 USB 3.0 ports though do not expect to see all of these present on a board at the same time, there is only so much bandwidth to go around, as M.2 slots were not mentioned and will also share the PCIe pool. If you are wondering what Intel Optane Technology is you can be forgiven as apparently calling it NVME support would be too easy.
As for the processor, it will remain LGA 1151 with power ranging from 35W to 95W which means it should be compatible with existing boards, assuming a UEFI update is released. The processor will support hardware acceleration for 10-bit VP9 playback and 10-bit HVEC encoding, as well as supporting 5K video at 30Hz and 60Hz, impressive for an onboard GPU. The processors will be unlocked and have enhanced BCLK overclocking as well. As you would expect the CPU is ready for NVMe, Thunderbolt 3 and even Intel RealSense. Follow the link if you want to give your translator program a workout.
Subject: Processors | November 5, 2015 - 09:30 PM | Sebastian Peak
Tagged: SoC, report, processor, mobile apu, leak, FX-9830PP, cpu, Bristol Ridge, APU, amd
A new report points to an entry from the USB implementors forum, which shows an unreleased AMD Bristol Ridge SoC.
(AMD via VideoCardz.com)
Bristol Ridge itself is not news, as the report at Computer Base observes (translation):
"A leaked roadmap had previously noted that Bristol Ridge is in the coming year soldered on motherboards for notebooks and desktop computers in special BGA package FP4."
(USB.org via Computer Base)
But there is something different about this chip as the report point out the model name FX-9830P pictured in the USB.org screen grab is consistent with the naming scheme for notebook parts, with the highest current model being FX-8800P (Carrizo), a 35W 4-thread Excavator part with 512 stream processors from the R7 GPU core.
(BenchLife via Computer Base)
No details are available other than information from a leaked roadmap (above), which points to Bristol Ridge as an FP4 BGA part for mobile, with a desktop variant for socket FM3 that would replace Kaveri/Godavari (and possibly still an Excavator part). New cores are coming in 2016, and we'll have to wait and see for additional details (or until more information inevitably leaks out).
Update, 11/06/15: WCCFtech expounds on the leak:
“Bristol Ridge isn’t just limited to mobility platforms but will also be featured on AM4 desktop platform as Bristol Ridge will be the APU generation available on desktops in 2016 while Zen would be integrated on the performance focused FX processors.”
WCCFtech’s report also included a link to this SiSoftware database entry for an engineering sample of a dual-core Stoney Ridge processor, a low-power mobile part with a 2.7 GHz clock speed. Stoney Ridge will reportedly succeed Carrizo-L for low-power platforms.
The report also provided this chart to reference the new products:
Subject: Graphics Cards | August 24, 2015 - 02:37 PM | Sebastian Peak
Tagged: rumor, report, Radeon R9 Nano, R9 290X, leak, hot chips, hbm, amd
A report from German-language tech site Golem contains what appears to be a slide leaked from AMD's GPU presentation at Hot Chips in Cupertino, and the results paint a very efficient picture of the upcoming Radeon R9 Nano GPU.
The spelling of "performance" doesn't mean this is fake, does it?
While only managing 3 FPS better than the Radeon R9 290X in this particular benchmark, this result was achieved with 1.9x the performance per watt of the baseline 290X in the test. The article speculates on the possible clock speed of the R9 Nano based on the relative performance, and estimates 850 MHz (which is of course up for debate as no official specs are known).
The most compelling part of the result has to be the ability of the Nano to match or exceed the R9 290X in performance, while only requiring a single 8-pin PCIe connector and needing an average of only 175 watts. With a mini-ITX friendly 15 cm board (5.9 inches) this could be one of the more compelling options for a mini gaming rig going forward.
We have a lot of questions that have yet to be answered of course, including the actual speed of both core and HBM, and just how quiet this air-cooled card might be under load. We shouldn't have to wait much longer!
Subject: Processors | August 3, 2015 - 10:58 AM | Sebastian Peak
Tagged: Skylake, leak, Intel, i7-6700K, Core i7-6700K
Leaked photos of what appear to be the full retail box version of the upcoming Intel Core i7-6700K and i5-6600K "Skylake" unlocked CPU have appeared on imgur, making the release of these processors feel ever closer.
Is this really the new box graphic for the unlocked i7?
While the authenticity of these photos can't be verified through any official channel, they certainly do look real. We have heard of Skylake leaks - a.k.a. Skyleaks - for a while now, and the rumors point to an August release for these new LGA 1151 chips (sorry LGA 1150 motherboard owners!).
Looks real. But we do live in a Photoshop world...
We only have about four weeks to wait at the most if an August release is, in fact, imminent. If not, I blame Jeremy for getting our hopes up with terms like Skyleak™. I encourage you to direct all angry correspondence to his inbox.
These boxes are very colorful (or colourful, if you will)
Chart taken from WCCFTech
The pricing of the top i7 part at $316 would be a welcome reduction from the current $339 retail of the i7-4790K. Now whether the 6700K can beat out that Devil's Canyon part remains to be seen. Doubtless we will have benchmarks and complete coverage once any official release is made by Intel for these parts.
Subject: Graphics Cards | June 12, 2015 - 10:31 PM | Ryan Shrout
Tagged: Skylake, leak, hbm, fury x, Fury, Fiji, amd
You just never know what's going to come your way on Facebook on a Friday night. Take this evening for me: there I was sitting on the laptop minding my own business when up pops a notification about new messages to the PC Perspective page of FB. Anonymous user asks very simply "do you want pictures of skylake and r9 fury x".
With a smirk, knowing that I am going to be Rick-rolled in some capacity, I reply, "sure".
Well, that's a lot more than I was expecting! For the first time that I can see we are getting the entire view of the upcoming AMD Fury X graphics card, with the water cooler installed. The self-contained water cooler that will keep the Fiji GPU and its HBM memory at reliable temperatures looks to be quite robust. Morry, one of our experts in the water cooling fields, is guessing the radiator thickness to be around 45mm, but that's just a guess based on the images we have here. I like how the fan is in-set into the cooler design so that the total package looks more svelte than it might actually be.
The tubing for the liquid transfer between the GPU block and the rad is braided pretty heavily which should protect it from cuts and wear as well as help reduce evaporation. The card is definitely shorter compared to other flagship graphics cards and that allows AMD to output the tubing through the back of the card rather than out the top. This should help in smaller cases where users want to integrate multi-GPU configurations.
This shot shows the front of the card and details the display outputs: 3x DisplayPort and 1x HDMI.
Finally, and maybe most importantly, we can see that Fiji / Fury X will indeed require a pair of 8-pin power connections. That allows the card to draw as much as 375 total watts but that doesn't mean that will be the TDP of the card when it ships.
Also, for what it's worth, this source did identify himself to me and I have no reason to believe these are bogus. And the name is confirmed: AMD Radeon Fury X.
Overall, I like the design that AMD has gone with for this new flagship offering. It's unique, will stand out from the normal cards on the market and that alone will help get users attention, which is what AMD needs to make a splash with Fiji. I know that many people will lament the fact that Fury X requires a water cooler to stay competitive, and that it might restrict installation in some chassis (if you already have a CPU water cooler, for example), but I think ultra-high-end enthusiasts looking at $600+ GPUs will be just fine with the configuration.
There you have it - AMD's Fury X graphics card is nearly here!
Subject: General Tech | June 12, 2015 - 01:14 PM | Jeremy Hellstrom
Tagged: hbm, leak, fury x, amd, Fiji, radeon, 390x
The rumours are flying today, with some purportedly leaked performance results of AMD's upcoming Fiji XT based card, the Fury X. The leak at Videocardz shows the results of 3DMark's Firestrike Ultra and Extreme for an AMD Radeon Graphics Processor in single card configuration and Crossfire results for Extreme only. The results show a card that can keep up with the Titan X and by extension the new GTX 980 Ti as well. At 1440p resolution, the Firestrike Extreme benchmark, the new AMD card seems to lag slightly behind NVIDIA in single and dual GPU configurations, but not by much while in the Ultra test at 4K the AMD GPU pulls ahead, likely thanks to the new HBM-1 memory.
They also claim to have a source who has run the new GPU though the CompuBench suite which gives us more information about the general architecture. The tests show a card with 64 Compute Units, which translates into 4096 Stream Cores if it is designed similarly to current Radeons. The tests also confirm the 1050MHz core clock and more interestingly the 4GB of HBM-1 will be clocked at 500MHz memory clock with a 4096-bit bus, which is good news for those who like their resolutions as high as they can go. Nothing is confirmed yet but these numbers bode well for the new Radeon architecture if they are true.
(Image credit: VideoCardz.com)
Subject: Graphics Cards | June 10, 2015 - 02:34 AM | Sebastian Peak
Tagged: rumor, Radeon 390X, radeon 390, radeon, leak, Hawaii XT, hawaii, amd
Here we go again...
Image credit: WCCFtech
Even more information has allegedly leaked out ahead of AMD’s official announcement of new 300-series Radeon GPUs, this time from rumor site WCCFtech. This information is totally unverified at least from any public source, but it is very specific regarding both price and GPU.
Here is the list published by WCCFtech in their report:
|R9 390X 8GB||Enhanced Hawaii XT||$389|
|R9 390 8GB||Enhanced Hawaii Pro||$329|
|R9 380X 3GB/6GB||Tonga XT (NOT CONFIRMED)|
|R9 380 4GB||Tonga Pro||$235|
|R9 380 2GB||Tonga Pro||$195|
|R7 370 4GB||Pitcairn||$175|
|R7 370 2GB||Pitcairn||$135|
|R7 360 2GB||Bonaire||$107|
As to whether this comes via leaked slides or is complete guesswork, we’ll likely have no answer until the official unveiling. Such an announcement is likely the purpose of the AMD gaming event at E3 which is now just days away. We can only hope that Fiji will in fact be making an appearance at the show as it does not appear on this list (again, if accurate).