Subject: General Tech | February 17, 2019 - 10:34 AM | Tim Verry
Tagged: turing, tu116, nvidia, gtx 1660 ti, 12nm
The rumor mill is churning out additional information on the alleged NVIDIA GTX 1660 Ti graphics card as it gets closer to its purported release date later this month. Based on the same Turing architecture as the already launched RTX series (RTX 2080, RTX 2070, RTX 2060), the GTX 1660 Ti will reportedly use a smaller TU116 GPU (specifically TU116-400-A1) and 6GB of GDDR6 memory on a 192-bit memory bus. Spotted by VideoCardz, TU116 appears to be pin compatible with TU106 (the GPU used in RTX 2060) but the die itself is noticeably smaller suggesting that TU116 is a new GPU rather than a cut down TU106 GPU with hardware purposefully disabled or binned down due manufacturing defects.
A bare MSI GTX 1660 Ti Ventus XS graphics card courtesy VideoCardz.
Rumor has it that the GTX 1660 Ti will feature 1536 CUDA cores, 96 Texture Units, and an unknown number of ROPs (possibly 48 though as the memory bus is the same as RTX 2060 with its 192-bit bus). Clockspeeds will start at 1500 MHz and boost to 1770 MHz. The 6GB of GDDR6 will be clocked at 6000 MHz. VideoCardz showed off an alleged MSI GTX 1660 Ti graphics card with the cooler removed showing off the PCB and components. Interestingly, the PCB has six memory chips on board for the 6GB GDDR6 with spots and traces for two more chips. Don't get your hopes up for an 8GB card however, as it appears that NVIDIA is simply making things easier on AIB partners by using pin compatible GPUs allowing them to reuse boards for the higher end graphics card models for the GTX 1660 Ti. The PCB board number for the GTX 1660 Ti is PG161 and is similar to the board used with RTX 2060 (PG160).
Enthusiasts' favorite twitter leaker TUM_APISAK further stirs the rumor pot with a leaked screenshot showing the benchmark results of a GTX 1660 Ti graphics card in Final Fantasy XV with a 1440p High Quality preset. The GTX 1660 Ti allegedly scored 5,000 points putting it just above the GTX 1070 at 4,955 points and just under the 980 Ti's 5052 score. Compared to the other side, the GTX 1660 Ti appears to sit between a presumably overclocked RX Vega (4876) and a Radeon Vega II (5283).
@TUM_APISAK shows off a FF:XV benchmark run including results from an unspecified GTX 1660 Ti graphics card.
Other performance rumors suggest that the GTX 1660 Ti will offer up 5.44 TFLOPs. RT cores are apparently cut (or disabled) in this GPU, but it is not clear whether or not the Tensor cores are intact (rumors seem to say yes though).
Nvidia GTX 1660 Ti graphics cards based on the TU116 GPU will reportedly start at $279 [update: VideoCardz claims the pricing has been confirmed from information given to reviewers] and may well launch as soon as February 22nd (though they've already missed one rumored launch date on the 15th...). Assuming for a minute the performance factors are true, it is interesting to see the smaller TU116 GPU with fewer CUDA cores at least getting close to GTX 1070 performance. The GTX 1070 uses the 16nm GP104 GPU (7.2B transistors) with 1920 CUDA cores (1506 MHz), 120 texture units, 64 ROPs, and 8GB of memory on a 256-bit bus clocked at 8000 MHz. The GTX 1070 offers up to 5.7 TFLOPS. Looking at the progress over the past few generations, it is neat to see that as architectures improve, they are able to do more work with less (but better/faster) CUDA cores. I would guess that the GTX 1660 Ti will not best the GTX 1070 in all games and situations though as the GTX 1070 does have more ROPs and more total memory (though the GDDR6 memory on GTX 1660 Ti does offer more bandwidth than the 1070's GDDR5 despite the smaller bus). Pricing will be interesting in this regard as the rumored price starts at $279 for GTX 1660 Ti. The cheapest GTX 1070 I found online at time of publication was $300 with most cards going for closer to $330+. We may see price drops on the older GTX 1070 cards as a result. GTX 1060 cards are going for $200+ and RX 580 cards are sitting at $190+, RX 590 at $260+, and Vega 56 prices starting at $330 (and go crazy high heh) so the GTX 1660 Ti may also push down the prices of the highe end and higher priced models of those cards as well.
What are your thoughts on the latest rumors?
- The GeForce GTX 1070 8GB Founders Edition Review
- NVIDIA GeForce RTX 2060 Review Part One: Initial Testing
- The Architecture of NVIDIA's RTX GPUs - Turing Explored
Subject: Editorial | October 24, 2018 - 09:13 PM | Josh Walrath
Tagged: amd, quarterly results, Q3 2018, ryzen, EPYC, Polaris, Vega, 7nm, 12nm, Intel, nvidia
This evening AMD announced their Q3 2018 results. Things were at the lower end of the guidance scale from last quarter, but the company still had some solid results. Q3 revenue was $1.65B as compared to Q3 2017’s $1.58B. It is down from the previous quarter’s high of $1.76B. At first glance this seems troubling, but the results are not as negative as one would assume. GAAP net income was a healthy $102M. Q3 2017 was at $61M while Q2 2018 was up at $116M. Profits did not fall nearly as much as one would expect with a decrease of $110M revenue quarter over quarter.
Probably the largest factor of the decrease was the negligible sales of GPUs to the crypto market. AMD had expected such a dropoff and warned about it in their Q2 guidance. That particular drop off was sudden and dramatic. AMD looks to continue to lose marketshare in add-in graphics due to their less competitive offerings across the spectrum. GeForce RTX sales of course did not impact AMD this previous quarter, but with no new AMD offerings on the horizon users look to have been waiting to see exactly what NVIDIA would release.
Ryzen sales have been steady and strong, making up some of the shortfall from the graphics market. Desktop chips are moving briskly for the company and continues to be a strong seller historically for the company. AMD is also starting to move more mobile processors, but it seems that the majority of parts are still desktop based. AMD looks to continue moving older inventory with aggressive pricing on those and manufacturing of the new 2000 series parts has been relatively smooth sailing for the company.
Enterprise, Embedded, and Semi-Custom had a strong quarter, but with less growth as some analysts had been hoping for. Semi-Custom was weaker this quarter, but IP revenue is up. Console chips are weaker at the moment due to the platforms being relatively mature and not exhibiting the sales of the previous two holiday seasons. To further offset the decrease in Semi-Custom, AMD is reporting that the enterprise products (GPU and EPYC) have seen good growth. Overall this division was down 5% from Q3 2017, but up 7% from the previous quarter.
Perhaps the most interesting figure of this is Gross Margins. AMD was able to improve margins from 36% to 40%. This 4% increase quarter on quarter is a significant jump for the company. This means that AMD continues to keep costs under control for the company and is able to deliver product more efficiently than in the year before. It is still a far cry from Intel and NVIDIA, which typically have magins between 55% to 65%. AMD has a long ways to go before reaching that kind of level. Part of the margin offset was again due to IP licensing. If IP licensing was removed then we would see 38% margins rather than 40%.
So what are the overall lessons of the past quarter? EPYC sales are not as brisk as analysts had hoped for, but they are also not non-existent. It has shown solid growth for the company and has offset shortfalls in other areas of the company. Their IP and Semi-Custom areas are still very solid, even though AMD does suffer from console lifecycles and downturns. GPUs continue to sell, but not nearly at the rate they were due to the crypto market. Their Polaris based options are well suited to compete in the sub-$300 US market. The Vega based products were finally down to MSRP, but they had a harder time going against the mature and well liked GeForce GTX 1070 and 1080 products. This will be further compounded with the introduction of the RTX products in those price ranges.
Ryzen continues to be a very good seller across the board. I had hoped that AMD would break down numbers between Ryzen CPUs and APUs, but I have not seen numbers that hint at what ratio they sell at. In retail the Ryzen 2000 series CPUs look to be some of the most popular products based on price/performance. However, retail is only a small portion of processor sales and Intel still holds the vast majority of marketshare here. AMD is competing, but they have not taken significant chunks from their competition over the past year. They have done enough to achieve several positive quarters in a row, but this is not the slam dunk that the original Athlon 64 was back in 2003/2004.
AMD expects further weakness in their results next quarter. Guidance is for revenue around $1.45B, plus or minus $50M. This is still higher than Q4 2017 results, but it is a significant drop from Q3 results. AMD expects strong Ryzen, EPYC, and datacenter GPU growth during this time. It is expected that consumer GPU and Semi-Custom will continue to drop. There does look to be a 7nm GPU introduction this next quarter, but it is probably the long rumored Vega refresh that will be aimed directly at datacenter rather than consumer.
2018 has so far been a year of solid growth and execution for AMD on the CPU side. Their GPU side has suffered a bit of a slide, but this is to be expected by how much belt-tightening AMD has done in the past several years to get their CPU architecture back on track. The lion’s share of development resources was shunted off to the CPU side while the GPU side had to fight for scraps. I believe this is no longer the case, but when development takes years for new GPUs the injection of new resources will not become apparent for a while.
2019 continues to look better for AMD as they are expecting an early release of 7nm EPYC parts which should compete very well with Intel’s 14nm based Xeon products. AMD is expecting a significant uptick in sales due to the thermals, pricing, and performance of these new Zen 2 based parts. The company also continues to point to the end of 1H for introduction of 7nm Ryzen parts based on Zen 2. These will be showing up quite a few months before Intel’s 10nm offerings will be available. Rumors have it that the new Zen 2 based parts exhibit a significant IPC increase that should make them far more competitive to the best that Intel has on the desktop and mobile markets. Combine these IPC improvements with the 7nm boost in power and clocks for the parts, and AMD could have a very good product on their hands. AMD also is expecting a 1H release of 7nm Navi GPUs which should prove to be more competitive with current NVIDIA products that rely on 16nm and 12nm process nodes from TSMC.
While Q3 was a drop in revenue for the company, their current cost structure has still allowed them to make a tidy profit. The company continues to move forward with new products and new developments.
Subject: Processors | August 6, 2018 - 09:00 AM | Ken Addison
Tagged: Zen+, XFR 2.0, Threadripper, StoreMI, ryzen, r7 2700x, Pinnacle Ridge, Intel, Core i9-780xe, amd, 2nd generation threadripper, 12nm
First teased at Computex earlier this summer, AMD has now released details and availability information for their 2nd Generation Threadripper CPUs.
Based upon the same 12nm Zen+ architecture we saw with the Pinnacle Ridge CPUs like the R7 2700X, Threadripper will now be split into two product families, the X, and the WX series.
The X-series is mostly a refresh of the Threaripper SKUs that we saw last year, with 12 and 16-core variants. The Threadripper 2920X and 2950X will retain the same two die, 4 CCX arrangement that we saw with the previous generation, with the ability to run in either unified or non-unified memory modes.
Notably, the 8-core variant found in the original Threadripper lineup seems to be absent in the 2nd generation.
This new generation of Threadripper comes in less expensive than the last, with a $50 price drop on the 12-core CPU, and a $100 price drop on the 16-core variant.
The newest aspect of the 2nd Generation Threadripper Lineup is the addition of the "WX" series processors. These higher core count processors are being marketed by AMD more towards "Creators and Innovators" rather than gamers.
Available in both 24 and 32-core variants, the Threadripper WX series represents the highest core count consumer CPUs ever launched. Since we know that Zen+ dies contain a maximum of 8 cores, we can assume that these processors are using a 4 die configuration, similar to the EPYC server parts, but likely with the same 64 lanes of PCIe and 4 channel memory controllers
This pricing is extremely aggressive compared to the highest core count competitor from Intel, the $2000 18-core i9-7980XE.
All 2nd Generation Threadripper CPUs will include the 2nd Generation Zen features that we saw in the R7 2600 and 2700 series, including XFR 2.0, StoreMI, and improved memory support and latency.
Additionally, these new Threadripper CPUs will use the existing X399 chipset, with UEFI updates being made available for existing X399 boards, as well as some new variants such as the MSI MEG X399 Creation launching alongside the new CPUs.
Availability of these processors is staggered, with the 32-core WX CPU shipping first on August 13th (and available now for preorder on Newegg and Amazon), followed shortly by the 16-core 2950X. However, we won't see the 12 and 24 variants until October.
Stay tuned for our review of these parts as they reach retail availability!
Subject: Editorial | July 25, 2018 - 09:47 PM | Josh Walrath
Tagged: Vega, ryzen, Q2 2018, Polaris, Intel, EPYC, amd, 7nm, 12nm
Today AMD has released their Q2 results for 2018 and they have fallen in line with previous estimates. The company reported revenue of $1.76B, up $110M from last quarter’s $1.65B. Their net income is $116M which is again up significantly from last quarter’s $81M. These results dwarf Q2 2017’s $1.15B in revenue and a loss of $42M. AMD has shown steady and solid growth since the release of the Ryzen processors and their continuing evolution of the RX series of graphics cards.
The computing group which includes CPUs and GPUs showed a small drop in revenue due to multiple factors. CPU ASPs are steadily dropping for AMD since the original introduction of the Ryzen processors. The top end R7 1800X was introduced at $499 and has slowly dropped in price as the year wore on. This year AMD released the successor to the 1800X in the R7 2700X, but it was released at a $329 price point. We can see that the pricing mix of these CPUs is not as rich as they were on Ryzen’s initial release. The play here seems to be AMD improving efficiency of production as well as a willingness to sacrifice ASPs to gain any kind of marketshare.
GPUs have suffered as well due to the drop off in mining based purchases due to cryptocurrency dropping in value as well as the continued introduction of specialized ASICs performing better in those particular workloads. AMD claims a fairly palatable drop of only around 4% in sales due to the decrease in mining demand. It is likely that partners are feeling more of a pinch in this instance as the selling prices of these cards are finally reaching introductory MSRP levels as well as seeing reasonable availability. We do not know the specifics of AMD’s GPU sales to partners, but it seems like that price has been stable since introduction with the partners and resellers profiting to a greater degree than AMD.
The bright spot for this quarter was that of Enterprise and Semi-Custom. AMD switched around accounting on how it handles Semi-Custom so that accounted for some of the positive gains this quarter saw. AMD also started its collaboration with the Chinese for their own version of a Zen CPU. AMD continues to provide console makers with SoCs in two of the three major product lines out there. AMD is also likely currently contracted by both Sony and Microsoft for the next generation of consoles which will be released in the next two years, though none of the parties involved in such speculation has verified that information. I have a hard time considering that both Sony and Microsoft would abandon what has been a very beneficial partnership to create cutting edge products for their marketplace.
The Enterprise group has also seen sales increase on the EPYC processors. EPYC was released last year, but it was not until this year that actual sales occured. While AMD did not provide specific numbers or guidance here, reading between the lines it looks as if EPYC is starting to gain traction and is shipping in more significant numbers. AMD was very careful in talking about this, as EPYC still has a long ways to go before it can claim to have gained significant marketshare. Lisa Su mentioned earlier that the real ramp for EPYC should occur in 2H 2018. This makes quite a bit of sense as the hardware and software environment for enterprise level products is tremendously different from when AMD was last competitive there. Validation of parts and platforms takes more time, and there are more complex software components involved that have to be updated to work effectively and efficiently on the new Zen architecture and EPYC chips. In the year since EPYC was launched a lot of work has been going on in the background by AMD, their hardware partners, and the software vendors to make sure that when EPYC hits volume production that most of the kinks will be worked out and it is truly enterprise production ready. This isn’t wishful thinking or excuse making. This is simply how a modern enterprise platform evolves and why product cycles are elongated as compared to what we see on the desktop and mobile spaces.
Guidance for next quarter will be disappointing for some investors and readers. AMD claims it will be flat between Q2 and Q3. This is not entirely surprising. Gaining desktop CPU marketshare has not been a slam dunk for AMD with Ryzen. The product stack has made it competitive with Intel and its offerings, and has in fact provided excellent value in terms of IPC and core count. Ryzen is not an Athlon 64. Ryzen was merely competitive with what Intel currently offers as compared to Athlon 64, which was head and shoulders more advanced than what Intel offered at the time with the Pentium 4. AMD is finding advances in marketshare in both desktop and mobile to be slow, but steady. Each quarter since Ryzen was released and the mobile parts being introduced earlier this year, the results have been trending in a positive direction even though ASPs on desktop parts have dropped (though mobile ASPs have increased).
AMD obviously does not expect big gains this next quarter, and are in fact a little behind the ball when it comes to graphics. NVIDIA is poised to release a new generation of products within the next few months addressing the upper midrange and high end offerings that will erode AMD’s effectiveness with their Vega parts. So while EPYC products will increase in sales, AMD looks like it will be shipping fewer GPUs, at least in the high end. We probably will see Polaris based products have price drops applied to them to keep the meat of the market satisfied with AMD product, but do not expect next generation desktop graphics from AMD until 2019.
This was a productive and solid quarter for AMD. It is hard to argue against that. Their financial house is in far greater order and a solid revenue stream heading towards the company. They are keeping costs under control while aggressively pursuing the markets they have a strong history in. They have continued to leverage their IP with the Semi-Custom group and that provides a steady income from both historical partners and new ones. AMD is not seeing a breakaway quarter or year, but they are building a much more solid foundation and executing on their primary markets while competing effectively with Intel. This is certainly not 2003/2004, but it is a new chapter for AMD as they continue to provide new and interesting products to a market that continues to expand.
Subject: Processors | June 5, 2018 - 11:03 PM | Ryan Shrout
Tagged: Threadripper, ryzen, amd, 32-core, 12nm
During the keynote address at Computex in Taipei, AMD SVP Jim Anderson was on stage to showcase a preview of the upcoming 2000-series of Threadripper processors for high-end consumer PCs. The Threadripper brand already made waves last year by bringing 16-core and 32-thread designs to the market for the very first time, improving performance for extreme productivity tasks, rendering, development, video, and more.
We knew that the 2000-series was coming this year, based on the 12nm process from GlobalFoundries, just as the Ryzen 2000-series uses, but we have narrowed the availability time frame to Q3 of 2018.
But the big story at the show was that this generation would see a doubling of the maximum core count on Threadripper. Yes, you will be able to buy 32-core and 64-thread AMD Threadripper CPUs later this year!!
Hot on the heels of the impressive, but dubiously cooled, Intel 28-core demo yesterday, AMD is clearly intent on continuing momentum that is has built throughout 2017. AMD didn’t show us any Cinebench numbers, but my understanding is that the demo provided was completely air cooled. Intel’s…not so much. While impressive to see 28-cores at 5 GHz yesterday, more impressive is a 32-core machine with a system design I would be willing to implement.
No more details on pricing, performance, or platform were made available during the keynote, but we’ll be asking those questions as the week progresses.
Get ready for 32-cores!!
Subject: Processors | April 25, 2018 - 09:45 PM | Josh Walrath
Tagged: Zen+, Vega, TSMC, ryzen, Results, Q1 2018, Polaris, GLOBALFOUNDRIES, financials, amd, 7nm, 12nm
Today AMD announced their latest financial results for Q1 2018. We expected it to be a good quarter with their guidance earlier this year, but I doubt many thought it would be as strong as it turned out to be. AMD posted revenue of $1.65 billion with a net income of $81 million. This is up from the expected $1.57 billion that analysts expected from what is typically a slow quarter. This is up 40% from Q1 2017 and its $1.18 billion and up 23% from Q4 2017.
There are multiple reasons behind this revenue growth. The compute and graphics segment lead the way with $1.12B of revenue. The entire year of 2017 AMD had released parts seemingly nonstop since March and the introduction of Ryzen. Q1 continued this trend with the release of the first Ryzen APUs with Vega Graphics introducing the 2000 series. AMD also ramped up production of the newly released Zen+ Ryzen chips and started shipping those out to retailers and partners alike. Initial mobile Ryzen parts were also introduced and shipped with SKUs being also shipped to partners who have yet to announce and release products based on these chips. Finally the strength of the Radeon graphics chips in both gaming and blockchain applications allowed them a tremendous amount of sellthrough throughout 2017 and into 2018. AMD estimates that 10% of the quarter was due to blockchain demand.
Enterprise, Embedded, and Semi-Custom had a revenue of $532 million, which is lower than most analysts expected. Semi-Custom in particular has seen a decline over the past few quarters with the release and saturation of the market of the latest console platforms utilizing AMD designed chips. It appears as though much of the contract is front loaded in terms of revenue with royalties tapering off over time as sales decrease. AMD did have some significant wins, namely providing Intel with Vega based GPUs to be integrated with Intel’s Kaby Lake-G based units. These declines were offset by the shipment of EPYC based processors that are slowly ramping and being shipped to partners to be integrated into server platforms later this year. We have seen a handful of wins from companies like Dell EMC, but AMD is still slowly re-entering the market that they were forced to abandon with their previous, outdated Opteron products. AMD expects to reach mid-single digit marketshare during 2019, but for now they are just getting off the ground with this platform.
The company is not standing still or resting on their laurels after the successful and heralded launch of the latest Ryzen 2000 series chips based on the Zen+ architecture. It is aggressively ramping their mobile chips featuring the Zen/Vega combination and have some 25 product wins being released throughout late spring and summer. Overall partners have some 60 products either shipping or will ship later this year featuring Ryzen based CPUs.
There is some fear that AMD will see its GPU sales throughput be impacted by the recent drop of cryptocurrency value. Several years back with the Bitcoin crash we saw a tremendous amount of secondhand product being sold and GPU revenues for the company tanked. AMD is a bit more optimistic about the upcoming quarter as they expect the current cryptocurrency/blockchain market is much more robust and people will be holding onto these cards to mine other products/workloads rather than drop them on eBay. My thought here is that we will see a rise in cards available on the secondary/used market, but quite a bit might be offset by latent gaming demand that has been held back due the outrageous prices of GPUs over the past year. People that have been waiting for prices to get back to MSRP or below will then buy. This could be further enhanced if memory prices start to drop, providing more affordable DDR4 and flash for SSDs.
The company is also forging ahead with advanced process technology. They have recently received silicon back from TSMC’s 7nm process and it looks to be a Vega based product. The rumor surrounding this is that it will be more of a compute platform initially rather than gaming oriented. Later this year AMD expects to receive new EPYC silicon, but it looks as though this will be from GLOBALFOUNDRIES 7nm process. AMD wants to be flexible in terms of manufacturing, but they have a long history with GLOBALFOUNDRIES when it comes to CPU production. The two companies work closely together to make sure the process and CPU design match up as cleanly as possible to allow products such as Zen to reach market successfully. The GPU arm is obviously more flexible here as they have a history with multiple foundry partners throughout the past two decades.
AMD has set an aggressive, but achievable, timetable of product releases that is initially focusing on the CPU side but would logically be transitioning to the GPU side. Zen+ is out on time and has met with acclaim from consumers and reviewers alike. The latest GPU products are comparable in performance to what NVIDIA has to offer, though they are less power efficient for that level of performance. The “pipecleaner” Vega on 7nm will pave the way towards Navi based products that look to be introduced next year. AMD could possibly refresh Vega on 12nm, but so far there has been no concrete information that such a product exists. They may very well continue to rely on current Polaris and Vega products throughout the rest of this year while focusing on Navi efforts to have a more competitive part come 2019.
Q2 2018 looks to be another successful quarter for AMD. The company’s outlook calls for revenue in the $1.725 billion range, plus or minus $50 million. AMD expects continued growth in all Ryzen product lines and greater throughput of EPYC based products as companies test and release products based on that platform. The GPU market could remain flat, but will most likely decline. That decline will be more than covered by the sell-through of the Ryzen line from top to bottom.
AMD improved their margin by an impressive 4%. Going from 32% to 36% showed the strength and higher ASPs of both CPU and GPU products. AMD expects another 1% increase over the next quarter. While these are good numbers for AMD, they do not match the 58%+ for NVIDIA and Intel when it comes to their margins. AMD certainly has a lot of room for improvement, and a richer product stack will allow them to achieve greater ASPs and see a rise in their overall margins. If EPYC becomes more successful, then we could see another significant improvement in margins for the company.
AMD is getting back to where they belong in terms of product placement, competitiveness, and financial performance. The company has seen a huge improvement year on year and hopes to continue that with a rich product stack that addresses multiple areas of computing. AI and machine learning is ramping up in the company in terms of software support as they feel their CPUs and GPUs are already good enough to handle the workloads. As more money comes in, they can afford to diversify and create a wider product base to compete in more markets. So far Lisa Su has been very, very successful in helping pull AMD from the ashes to the competitive situation that they currently find themselves in.
Subject: General Tech | September 28, 2017 - 12:23 PM | Jeremy Hellstrom
Tagged: 12nm, GLOBALFOUNDRIES, amd, ryzen, Pinnacle 7, Pinnacle 5, Pinnacle 3, Pinnacle, x470, b450
DigiTimes reports today that AMD has informed motherboard makers that their new series of chips, the Pinnacle family, will in launch early 2018. They will lead with the Pinnacle 7 series, with Pinnacle 5 and 3 series arriving in March. April will see the low powered models while Enterprise will have to wait for the Pro until May. The chips will be built on GLOFO's 12nm process and will hopefully build on AMD's current successes with Ryzen. You will also meet the new 400 series chipset, so far the X470 and B450 have been mentioned. While this is still officially a rumour, it is a fairly solid one.
"AMD has informed its partners that it plans to launch in February 2018 an upgrade version of its Ryzen series processors built using a 12nm low-power (12LP) process at Globalfoundries, according to sources at motherboard makers."
Here is some more Tech News from around the web:
- Power meltdown 'fries' SourceForge, knocks site's servers titsup @ The Register
- Intel's self-learning 'Loihi' AI chip wants machines to think like humans @ The Inquirer
- Bell Canada Wants Pirate Websites Blocked For Canadians @ Slashdot
- Have MAC, will hack: iThings have trivial-to-exploit Wi-Fi bug @ The Register
- Samsung tries to catch up Everspin on MRAM @ Electronics Weekly
- Internet Explorer flaw is exposing your search habits @ The Inquirer
- Helium's for balloons and squeaky voices, not this 10TB Toshiba beast @ The Register