Subject: Memory | November 25, 2008 - 01:23 PM | Jeremy Hellstrom
If you still aren't convinced that triple channel DDR3 is the solution to all your problems, this TweakTown review might not make up your mind completely, but it should help. In their synthetic testing, adding that third channel had the same results as a dual channel setup going from 1066MHz to 1600MHz. On the other hand, when they tested Crysis, the difference in performance is hard to spot on a graph and is most likely unnoticeable while playing.
Subject: Memory | November 19, 2008 - 03:46 PM | Jeremy Hellstrom
If you are looking for triple channel memory, consider Corsair's Dominator Tri-Channel DDR3-1600 6Gb kit, with timings of 8-8-8-24. They sport the now familiar DHX (dual-path heat eXchange) cooling system and as they run at 1.65V so heat will not be much of an issue with these DIMMs. CPU3D managed a fairly good overclock and recommend turning on XMP in your BIOS as it really changed the amount of throughput for these DIMMs. They didn't leave the c
Subject: Memory | November 17, 2008 - 01:47 PM | Jeremy Hellstrom
Corsair has run a long series of tests on their 1600MHz Corsair Dominator TR3X3G1600C8D series, comparing the performance between 3GB and 6GB on the new triple channel X58 based ASUS P6T Deluxe motherboard, an Intel Core i7-965 Extreme Edition, a pair of 1GB Nvidia GeForce 280 GTX in SLI and 2 Seagate Barracuda 7200.10 320GB in RAID 0. (So, you know, a system just like everyone has)
Subject: Memory | October 30, 2008 - 01:50 PM | Jeremy Hellstrom
4Gb of DDR2-800 @ 4-4-4-12 faces off against 4Gb clocked to DDR2-1,066MHz @ 5-5-5-15 at bit-tech. Many of us still haven't made the plunge into DDR3, especially with Nehalem looming in the near future and it's triple channel capabilities. If you are looking for extra speed in your DDR2 system, it's worth revisiting the differences you get in changing timing and overall speed.
Subject: Memory | October 23, 2008 - 02:49 PM | Jeremy Hellstrom
Crucial's new Ballistix Tracer DIMMS are DDR3-1333 with a CAS Latency of 6 and timings of 6-6-6-20. It runs at 1.8v, not low enough for a Corei7 system, but lower than many DDR3 kits available. You won't even need to pump the voltage up too high when overclocking, Think Computers hit DDR3-1818 8-8-8-24 and they only had to raise the DIMMs to 1.84v. You c
Subject: Memory | October 21, 2008 - 02:01 PM | Jeremy Hellstrom
Fremont, CA, October 21st, 2008 - Corsair, a worldwide leader in high performance computer and flash memory products, announced today that it is launching a full line of DDR3 performance memory products designed for Intel Core i7 processor.
Designed to take advantage of the Core i7 processor's triple-channel memory controller, Corsair will offer memory solutions supporting three different DDR3 memory speeds in triple memory packs: 1333MHz, 1600MHz and 1866MHz. The 1866MHz Corsair DDR3 modules will be the world's fastest Intel Core i7 solution.
Subject: Memory | October 16, 2008 - 06:38 PM | Jeremy Hellstrom
Sunnyvale, Calif. - October 16, 2008 - OCZ Technology Group, Inc., a
worldwide leader in innovative, ultra-high performance and high
reliability memory, today unveiled the industry's first triple channel
memory kit designed specifically for the impending Intel Core i7
processor/Intel X58 Express Chipset. Optimized for the Core i7's
triple channel mode, these new 3GB and 6GB kits ensure optimal
performance via an ideal combination of low voltage requirements,
speed, and latency.
Subject: Memory | October 9, 2008 - 12:14 PM | Jeremy Hellstrom
Speaking of low powered, high speed RAM; MektuMods have finished a round-up of high speed DDR3 of which only one DIMM, the CSX Diablo3 2000 2GB Kit requires 2V, the rest were designed to run between 1.8V - 1.95V, making them safe for the Core i7. Once they got into overclocking, the voltages did start to rise which could prove to be a problem for people really wanting to push Intel's upcoming chip. Drop by to see the strengths and weaknesses of each kit.
Subject: Memory | October 2, 2008 - 05:38 PM | Jeremy Hellstrom
While just about any DIMM you buy today has a heat spreader on it at the very least, not all of the cooling solutions offered by memory makers are as good as others. If you do find yourself having heat problems with your RAM, try the Thermaltake RamOrb memory cooler. The only major difficulty that you could encounter is the removal of the original heatsinks so that you can use the RamOrb, other than that it should be as easy as it was for TweakTown.
Subject: Memory | September 23, 2008 - 04:01 PM | Jeremy Hellstrom
The 1800MHz DDR3 Extreme Performance kit from Patriot sports their Aluminium Copper Composite heatsinks, which for some reason are painted green. The run 8-8-8-24 @ 1.9V out of the box, Pro-Clockers pushed them to 2000MHz by relaxing the timings to 9-9-9-24. The $339 price tag doesn't hurt either!