Review Index:
Feedback

Thermaltake Armor Revo Gene Mid-Tower Case Review

Manufacturer: Thermaltake

Exterior Case Overview

View Full Size

View Full Size

The Thermaltake Armor Revo Gene supports four 5.25" devices and one 3.5" device through its externally accessible front device bays. The slots themselves are covered with metal and plastic mesh bay covers, allowing for air pass-through. Additionally, Thermaltake included metal shutters on both sides of case front that can open and close. These wing-shaped shutters are more for looks than for actual function. The shutters may actually impede functioning of an optical drive or fan controller mounted in one of the 5.25" drive bays. At the bottom of the front panel is a 200mm blue LED fan, housed behind the plastic grill plate.

View Full Size

The left side panel contains window showing the upper half of the case's motherboard tray with space for up to a 200mm fan just below the window. No fan is included by default, but the built-in mount supports 120mm, 140mm, or 200mm fans. Notice that Thermaltake included four rubber grommets in the 200mm fan holes for fan vibration dissipation. These grommets can be removed and used in the other case fan mounting holes if desired. The right side panel also includes a fold-down headset holder to the right of the window. The mechanism is made from plastic, but should be sturdy enough for even the larger headsets. If you put your case under your desk, this holder could become a nuisance if you choose to use it for holding your headset though.

View Full Size

The back of the Armor Revo Gene sports the normal rear panel assembly hole for the motherboard's rear panel port, as well as a 140mm fan, tubing pass-through for external water cooling apparatus, seven expansion card slots, and a slot for the power supply at the bottom. The expansion card slots all have metal covers with holes for air passage and thumbscrews to hold the cards in place.

View Full Size

The three pass-through holes at the top of the case rear contain rubber grommets to better seal the openings should you chose to use the ports for water cooling tubes. Additionally, Thermaltake included rubber grommets on the four corners of the fan port to reduce fan vibration noise.

View Full Size

The case's right side panel is a solid metal panel covering the back of the motherboard tray. Even though the case side does not balloon out to better accommodate cable runs behind the motherboard tray, we found that there was sufficient room provided for most cable runs behind the tray.

View Full Size

The Armor Revo Gene case's top panel contains a holed fan grill that can accommodate a single 200mm, 140mm, or dual 120mm fans. At the front of the top panel are several device ports, case lights and buttons, and an integrated hot-swap drive bay.

View Full Size

The top panel contains 2 USB 3.0 device ports (blue colored USB ports), 2 USB 2.0 device ports (black colored USB ports), audio output port, and microphone input port. The case's power button is in the lower left corner of the assembly, with the hard drive activity light and case reset button above it. Notice how the buttons are flush with the case surface. The case power light is just under the front of the top panel contained under a stylized device logo. The LED illuminates a blue color when the system is actively powered with a breathing light effect.

View Full Size

View Full Size

The hot-swap drive bay built into the case's top panel offers support for both 2.5" and 3.5" hard drives. The bay hinge mechanism is built to support both sizes with the hole auto-expanding to accommodate the drive type used.

View Full Size

The case bottom features extra large case feet that can swivel a full 360 degrees with four locked positions. Additionally, there is a removable fan filter that covers the intake regions for the power supply fan as well an additional 120mm fan that can be added in front of the power supply unit.

View Full Size

When powered, the logo at the top front of the case glows the same color blue as the 200mm fan at the front bottom. Notice how some of the fan's light is redirected to the bottom of the case, giving it a ground-fx style look. The illuminated logo pulses in a breathing-style pattern as well.

January 28, 2013 | 02:09 PM - Posted by Chaitanya (not verified)

There is a small typo in paragraph under the photo where you have installed a mini-ITX board and it reads:"With a micro-ITX form factor board, the amount of free space seems to overwhelm the board." I believe there is no such form factor that exists. Its either micro-ATX or mini-ITX. please correct it.

January 28, 2013 | 04:05 PM - Posted by Morry Teitelman

Thank you for pointing this out. This has been corrected...

January 28, 2013 | 04:44 PM - Posted by markdek (not verified)

sb 3.0 x 2

should be usb 3.0 x 2 ?

January 28, 2013 | 05:55 PM - Posted by Morry Teitelman

Fixed, thanks for the heads up...

January 29, 2013 | 12:56 AM - Posted by Laurențiu Roman (not verified)

What kind of manufacturer puts out transparent hdds?

January 29, 2013 | 12:19 PM - Posted by Morry Teitelman

Western Digital released several of their Raptor drives with clear windows on top of them...

March 10, 2013 | 08:10 PM - Posted by Juan Carlos Caicedo H. (not verified)

hi man you made an excellent review, but i need your help. I bought this case in january and i want to put the side fan in the case, in the specs appear than the fan must be 200x200x30 so i got a 200mm thermaltake thunderblade led blue fan but it doesnt fit in the holes of the side of the case, when i read the box of the fan appear than it can be used in the front or the top of the cases, so i want to know if maybe the coolermaster 200mm megaflow can be used or wich reference fits well in the space of the side fan. Thanks. Juan C.

July 10, 2013 | 12:43 AM - Posted by Reginald (not verified)

i want to knw why is my breaathing light on my case not lighting up...? on my armor revo gene

September 23, 2014 | 05:02 AM - Posted by Robert Edvin (not verified)

I have this case and the front panel audio is not working. Also 3 more people with this case have the same problem. Don't really know why they came faulty from the manufacturer.

Post new comment

The content of this field is kept private and will not be shown publicly.
  • Lines and paragraphs break automatically.
  • Allowed HTML tags: <a> <em> <strong> <cite> <code> <ul> <ol> <li> <dl> <dt> <dd> <blockquote><p><br>
  • Web page addresses and e-mail addresses turn into links automatically.

More information about formatting options

By submitting this form, you accept the Mollom privacy policy.