Review Index:
Feedback

Thermaltake Armor Revo Gene Mid-Tower Case Review

Manufacturer: Thermaltake

Case Deconstructed

View Full Size

View Full Size

View Full Size

The case's front panel is held in place by large push-pins that mate to holes in the front of the case. The external 5.25" and 3.5" bays have removable plastic face plates covered with metal mesh. On the backside of the lower portion of the panel is a fan filter assembly that can be removed for cleaning.

View Full Size

View Full Size

View Full Size

Underneath the plastic front faceplate are the 5.25" and 3.5" device bays as well as the front 200mm fan. There are two 3.5" drive bays with one tucked away behind the upper portion of the fan. The fan itself has clear blades to better enhance and reflect the blue LED illumination.

View Full Size

View Full Size

The aluminum front guards are held in place with plastic hinges at the top and bottom of each guard. The hinges slide up and down to seat or unseat the holding pin from its mating hole in the front faceplate.

View Full Size

To connect the case's upper panel assembly, cables and header plugs are provided. The 4-pin molex connector powers the upper panel assembly and LEDs with the two 3-pin fan cables attaching to the top and front case fans. The header plugs for the front panel assembly include a USB 2.0 plug, a USB 3.0 plug, a front panel audio plug, a front panel plug (for connecting the power LED, HD LED, and power and reset buttons), and a SATA plug for the hot-swap drive bay.

View Full Size

View Full Size

The case expansion card slot area in the rear of the case is comprised of three major parts - the hold-down plate, the expansion slot covers, and the thumbscrews. The hold-down plate acts as added support that sits on top of the expansion card uprights. This system allows for removable of expansion card plates without having to go into the case at all. Notice the latch on the bottom of the expansion card slot covers that hold the covers in place at the bottom of the slot. I am not a big fan of this implementation because of case security concerns. It would be very easy for someone during a LAN party to get into your case and muck around without having to even remove a side panel.

View Full Size

View Full Size

The 3.5" drive cages are a single plastic unit with a front accessible removal mechanism. You simply squeeze together the two front levers and pull out the cage. Unfortunately, the cages are not tool-less, so the drives must be set in place with the provided drive screws. However, Thermaltake does include four rubber grommets in the sides of each cage to held with drive noise and vibration. Notice that there are holes provided in the bottom supports of the drive cage for mounting 2.5" drives like SSDs.

View Full Size

One of the nicer additions to the case side panels are the thumbscrews. Thermaltake designed the thumbscrews to be held in place after panel removal, so that you do not have to worry about losing track of them. They did this by making the threading on the thumbscrew wider than the hole with the thumbscrew portion in contact with the panel being unthreaded.

View Full Size

The included fan in the top panel is a 200mm fan with a unique fin design. Not only did they manage to cram 11 fins onto the fan motor, but the fins have feathered notches cut into the leading edge of each one. This notched design allows for better and more directed airflow during low speed fan operation.

View Full Size

View Full Size

View Full Size

The mesh fan filter and window on the case's left side panel are held in place with removable black plastic rivets. Use of these type of rivets give the panel assembly a uniform look to blend with the metal rivets used in other areas of the case. Additionally, they make for easy removal if you want to modify the panel without affecting the window. To remove the rivets, you simply push the shaft out of the holder from the back of the panel using a small flat-head screwdriver and pull the head unit free. The hold-down piece will come free easily at that point.

January 28, 2013 | 02:09 PM - Posted by Chaitanya (not verified)

There is a small typo in paragraph under the photo where you have installed a mini-ITX board and it reads:"With a micro-ITX form factor board, the amount of free space seems to overwhelm the board." I believe there is no such form factor that exists. Its either micro-ATX or mini-ITX. please correct it.

January 28, 2013 | 04:05 PM - Posted by Morry Teitelman

Thank you for pointing this out. This has been corrected...

January 28, 2013 | 04:44 PM - Posted by markdek (not verified)

sb 3.0 x 2

should be usb 3.0 x 2 ?

January 28, 2013 | 05:55 PM - Posted by Morry Teitelman

Fixed, thanks for the heads up...

January 29, 2013 | 12:56 AM - Posted by Laurențiu Roman (not verified)

What kind of manufacturer puts out transparent hdds?

January 29, 2013 | 12:19 PM - Posted by Morry Teitelman

Western Digital released several of their Raptor drives with clear windows on top of them...

March 10, 2013 | 08:10 PM - Posted by Juan Carlos Caicedo H. (not verified)

hi man you made an excellent review, but i need your help. I bought this case in january and i want to put the side fan in the case, in the specs appear than the fan must be 200x200x30 so i got a 200mm thermaltake thunderblade led blue fan but it doesnt fit in the holes of the side of the case, when i read the box of the fan appear than it can be used in the front or the top of the cases, so i want to know if maybe the coolermaster 200mm megaflow can be used or wich reference fits well in the space of the side fan. Thanks. Juan C.

July 10, 2013 | 12:43 AM - Posted by Reginald (not verified)

i want to knw why is my breaathing light on my case not lighting up...? on my armor revo gene

September 23, 2014 | 05:02 AM - Posted by Robert Edvin (not verified)

I have this case and the front panel audio is not working. Also 3 more people with this case have the same problem. Don't really know why they came faulty from the manufacturer.

Post new comment

The content of this field is kept private and will not be shown publicly.
  • Lines and paragraphs break automatically.
  • Allowed HTML tags: <a> <em> <strong> <cite> <code> <ul> <ol> <li> <dl> <dt> <dd> <blockquote><p><br>
  • Web page addresses and e-mail addresses turn into links automatically.

More information about formatting options

By submitting this form, you accept the Mollom privacy policy.