Review Index:
Feedback

Corsair RM Series 550W Power Supply Review

Manufacturer: Corsair

Efficiency, Differential Temperature and Noise

Efficiency

Efficiency is defined by the power output divided by the power input and is usually expressed as a percentage.  If a PSU were a 100% efficient (which none are) 500 watts of AC power going in would result in 500 watts of DC power coming out (with no waste heat to dissipate).  In the real world there are always inefficiencies and power is lost in the form of heat during the conversion process. Newer revisions to the ATX12V Power Supply Design Guide V 2.2 have continued to increase the efficiency recommendations for PC switching mode power supplies and now lists both required and recommended minimum efficiencies.

View Full Size

We measured the AC power input to the Corsair RM550 PSU with an Extech power analyzer while the total DC load was found by adding all the individual +3.3V, +5V, +12V, -12V and +5VSB loads together. 

View Full Size

View Full Size

The overall efficiency of the RM Series 550W power supply is very good and easily meets the criteria for 80Plus Gold certification, even while operating on 115 VAC and at elevated, real-world temperatures. 

80 Plus Program

View Full Size

Note 1: Power Factor ≥0.90 (50% to 100% Load)
Note 2: Tests conducted at room temperature (25°C)

Differential Temperature and Noise Levels

To simulate real world operation, some of the warm exhaust air from the PSU under test is recirculated back to the intake through a passive air duct, which allows the PSU air inlet temperature to increase with load, just like it would in a real PC. 

The differential temperature across the power supply was calculated by subtracting the internal case air temperature (T in) from the temperature of the warm exhaust air flowing out the back of the power supply (T out). 

Thermocouples were placed at the air inlet and exhaust outlet. The ambient room air temperature was 23ºC (74ºF) +/- 0.5ºC during testing.

T out = temperature of air exhausting from power supply
T in = temperature of air entering power supply
Delta T = T out - T in

Sound pressure level readings were taken 3’ away from the rear of the case in an otherwise quiet room.  The ambient noise level was ~27 dBA. 

View Full Size

*Note: Fan not spinning

At low to mid power levels (10-50% load) the cooling fan was not spinning and the power supply was dead silent. As soon as I started to increase the loads to Test 4 (412.5W load) the fan started spinning and cycled on and off for few seconds before settling down. At full load the fan sped up to the point where it was subjectively very noticeable.  I was not able to take SPL readings at the higher loads due to the background noise generated by all the DC Load cooling fans cycling on and off.  This normally wouldn’t be an issue with output power of 550W but since the RM550 only has two PCI-E connectors I was only able to use three programmable loads on the +12V output instead of my usual four.

September 23, 2013 | 02:15 AM - Posted by sergio (not verified)

What do you think, is it OK to use this power supply in bottom-mounted-PSU cases? My concern is fan outake in limited space and directed downwar.? On loads below 50%, what's going to be with heat dissipation?

September 23, 2013 | 08:18 AM - Posted by jonnyguru (not verified)

sergio: Fans in power supplies are intake, not exhaust.

September 23, 2013 | 04:22 PM - Posted by Anonymous (not verified)

2 pci-e connectors a positive? That should be a negative. All 550w psu's in this day and age should have 4 pci-e connectors.

September 24, 2013 | 05:45 AM - Posted by rrr (not verified)

Unless you plan on running stuff like 2x 670 or 2x 7950, which is pushing 550W unit, I disagree.

2 PCI-E is IMO fine for 550W. Not so for 650W OTOH.

December 16, 2013 | 05:43 PM - Posted by psumaster (not verified)

There are videocards coming with 3 PCI-E, so I think at least 3 would be a good number. 2 PCI-E should be the default for 400W units.

September 24, 2013 | 09:19 AM - Posted by Mark "Dusty" D (not verified)

Lee, on the Specifications and Packaging page, the efficiency and fan noise curves show the x axis as sytem load (watts), but it is expressed in percentages of full load. Conversely, on the DC Load Regulation and AC Ripple page, it shows the wattage being drawn but would be more helpful in percent of full load.

March 1, 2014 | 07:05 PM - Posted by Anonymous Cowerd (not verified)

Would like an article
that compares the cost between the common recommendation
by all to take a PSU that's double your consumption
and a PSU that's just enough above your system consumption.

Example for calculated comparison:
PC1 peek consumption is 380w - PSU is 450W.
PC2 peek consumption is 380W - PSU is 750W.
(both the same 80+ rate)

PC#1 would be far from optimal, but buying cost is low.
PC#2 is in middle of the bell curve efficiency chart,
but cost more!

since the drop between PSU #2 & #1 efficiency is just few percent's would it make buying the more expansive PSU worth while, for the average warranty of the PSU?

Such article would greatly benefit PCPER community.

Post new comment

The content of this field is kept private and will not be shown publicly.
  • Lines and paragraphs break automatically.
  • Allowed HTML tags: <a> <em> <strong> <cite> <code> <ul> <ol> <li> <dl> <dt> <dd> <blockquote><p><br>
  • Web page addresses and e-mail addresses turn into links automatically.

More information about formatting options

By submitting this form, you accept the Mollom privacy policy.