Review Index:

Corsair Hydro Series H90 and H110 140mm-Based Liquid Cooler Review

Manufacturer: Corsair

Hydro Series Shared Components

View Full Size

View Full Size

Hardware-wise, Corsair includes all mounting pieces necessary to get the cooler up and running on any current AMD or Intel based system. The plastic pieces snap together on the upper hold-down plates to secure the thumbscrew in place. The thumbscrews with the larger threaded section are used for mounting to an LGA1155, LGA1366, and AMD-based sockets, while the thumbscrews with the smaller threaded section are used for LGA2011-based mounting. Also included are fan screws and washers for affixing the fans to the cooler radiator. The screws included for the fans are 6 x 32 x 1 1/4" screws - #6 machine thread, 32 TPI (threads per inch), 1.25 inches in length. Notice that all hardware is colored black or black chromed to match the Hydro Series™ cooler coloring.

View Full Size

Intel LGA1155/1156 hole configuration

View Full Size

Intel LGA2011/LGA1366/AMD hole configuration

The plastic thumbscrew inserts can be mounted to the CPU hold-down plate with the top hole towards the outside of the arm or to the inside of the arm. For use with Intel LGA2011, Intel LGA1366, and AMD-based sockets, the insert holes must be mounted in the outside configuration. For Intel LGA1155 or Intel LGA1156-based sockets, the insert holes must be mounted towards the inside of the arm.

View Full Size

The metal nuts are slid into the underside of the plastic under-board plates to act as screw in points for the thumbscrews. The Intel LGA2011-based socket is the only exception since that socket has its own integrated under-board plate. For the AMD under-board plate, the nuts can only be mounted in a static configuration. The Intel-based plates support three configurations which are marked on the underside of the plate: LGA1366, LGA1156 (works for LGA1155 also), and LGA775. Be careful to mount the nut into the correct configuration holes or else you'll run into problems when mounting the cooler.

View Full Size

Intel LGA1155 mount assembly - top view

View Full Size

Intel LGA1155 mount assembly - side view

To assemble the mounting system, the top plate L-shaped brackets fit into slots along the outer edges of the CPU unit's cover. The round ring then snaps unto the bottom of the assembly to hold the top-plate securely in place as shown in the unit pictures.

View Full Size

Both coolers come standard with Corsair labeled 140mm x 140mm x 25mm fans, rated at 12V and 0.4 amps. The fans are equipped with 4-pin fan connectors and all have 9 large fins to promote higher airflow with minimal air noise. The only difference between the H110 and H90 units is that the H90 unit includes only a single fan.

February 27, 2013 | 02:09 AM - Posted by razor512

Great review, will try to save up for one for my AMD CPU that keeps hitting 70c at load using the sunbeam core contact cooler

February 27, 2013 | 03:28 AM - Posted by John Doe (not verified)

Mind you that the CCF is a direct touch heatpipe cooler, so you might want to check out if it's making contact well, and re-TIM if necessary.

I had one back in the day and even thought a cheap cooler, it wasn't that bad. It did the job and kept my E6600 cool. It's not all that well built though you might want to remount it or slap a second fan to it somehow. A second fan would help that cooler.

And well, I wouldn't suggest these cheap AIO water loops. Just get a TPC-812 and be done with it.

September 7, 2013 | 07:18 PM - Posted by stas (not verified)

tell me please guys, does corsair h110 fits inside thermaltake armor revo case?

Post new comment

The content of this field is kept private and will not be shown publicly.
  • Lines and paragraphs break automatically.
  • Allowed HTML tags: <a> <em> <strong> <cite> <code> <ul> <ol> <li> <dl> <dt> <dd> <blockquote><p><br>
  • Web page addresses and e-mail addresses turn into links automatically.

More information about formatting options

By submitting this form, you accept the Mollom privacy policy.