All | Editorial | General Tech | Graphics Cards | Networking | Motherboards | Cases and Cooling | Processors | Chipsets | Memory | Displays | Systems | Storage | Mobile | Shows and Expos
We caught wind of a leaked Intel SSD Roadmap over at VRZone. The slide shows their rough release plans into early 2014:
Starting bottom-up, the old 320 Series (cropped slide bottom) and 330 Series are being phased out in light of the newer 500 series entrants. The 335 Series, driven by a SandForce controller and 20nm flash, may drop in capacity to only an 80GB model in order to drive customers towards the new 530 Series, which will replace both of the SandForce-driven 520 (SATA) and 525 Series (mSATA) offerings. The new 530 Series will be available in 80-480GB and connect via SATA, mSATA, and the newest M.2 SATA interfaces. You can learn more about M.2 by reading the first 6 or so slides from Paul Wassenberg's presentation from Storage Visions 2013. Here's a closer look at an M.2 unit:
From CES 2013, a Micron mSATA SSD (above) and M.2 SATA SSD (below).
With the 530 appearing to become Intel's big mainstream consumer push, they will also introduce a Pro 1500 and 2500 Series. I suspect Intel's own SATA 6Gb/sec controller will be lifted from their SSD DC S3500 and S3700 Series and trickled down into the Pro Series and possibly even into the 530 Series, though that is only speculation on my part.
For the enterprise, Intel will be further juggling their enterprise models around a bit, discontinuing the SSD 710 and possibly even the (25nm) S3700 in favor of the (20nm) S3500 Series, which will also see large gains in available capacity upwards of 800GB and even 1.6TB crammed into a 2.5" SATA unit. Intel's PCIe SSD 910 will eventually be replaced by what appears to be a quad-SSD-RAID variant of the current S3500 and S3700 Series units, dubbed P3500 and P3700, respectively. These models should show a substantial gain over the SSD 910, which did not perform spectacularly when compared to the newer SATA models available.
Subject: General Tech, Storage | June 28, 2013 - 01:24 PM | Jeremy Hellstrom
Tagged: western digital, Arkeia, backup
IRVINE, Calif. – June 27, 2013 – WD®, a Western Digital (NASDAQ: WDC) company and world leader in digital storage solutions, today unveiled the fourth generation of WD Arkeia™ network backup appliances, delivering an all-in-one backup and disaster recovery solution for small- and medium-sized businesses (SMBs).
The new line up consists of four rack-mount appliance models with larger internal disk capacities, faster processors, increased memory, and integrated solid state drives (SSDs) to shorten backup time and accelerate data recovery. The bundled WD Arkeia v10.1 software delivers new support for “seed and feed” technology to support hybrid cloud backups. This allows companies to move backups offsite via network replication rather than shipment of tapes.
“In announcing their fourth generation of purpose-built network backup appliances, WD Arkeia is delivering comprehensive SMB backup solutions that go beyond simple raw capacity increases,” said Liz Conner, senior research analyst, IDC. “WD Arkeia offers easy- to-use data protection that takes the guess work out of purchasing, configuring and managing data backup and recovery, while also embedding features such as deduplication and hybrid cloud backup for small- and medium-sized businesses or remote offices." “WD is committed to providing the growing SMB marketplace with a comprehensive suite of storage solutions,” said Jim Welsh, executive vice president and general manager of WD’s branded business unit. With unique features, these next-generation WD Arkeia network backup appliances offer solutions providers and their customers a simple, smart way to protect their data.
Fourth-Generation Performance and Ease-of-Use
Fourth-generation WD Arkeia backup appliances deliver performance and ease-of-use at an affordable price for SMBs. These new appliances extend the upper range of WD Arkeia appliances and complement available lower-range appliances. WD Arkeia R120s and R220s, both with optional LTO4 tape drives, integrate dual-core Atom and quad-core Xeon processors, respectively. Existing appliances deliver disk capacities from 2TB to 12TB and will also bundle WD Arkeia v10.1. The new fourth-generation appliances offer: o Increased Backup and Recovery Speed: New features include integrated LTO5 tape drives, processor upgrades to a maximum of 2 hex-core Intel® Xeon®, integrated SSDs on select models, and memory up to 96 GB to allow for increased data backup and recovery speeds of both files and disk images. WD Arkeia’s patented Progressive Deduplication™ technology accelerates backups by compressing data at source computers before transfer over local area networks (LANs) or wide area networks (WANs).
- Higher Storage Capacity: Storage capacity doubles from the third generation, with raw capacity now ranging up to 48 TB, configured in RAID-6.
- Improved Ease of Use: Version 10.1 of WD Arkeia software, delivered with the new generation, includes an on-boarding wizard to streamline the appliance setup process.
- Storage Reliability: All new WD Arkeia appliances feature WD enterprise-class WD RE™ hard drives for maximum data integrity.
- Simplified Tape-free, Offsite Storage: Version 10.1 of WD Arkeia software extends support for hybrid cloud backup capabilities to the full line of WD Arkeia appliances. “Seed and feed” capabilities allow administrators to supplement network replication of backup sets offsite by using USB-connected hard drives to transfer initial and large backup sets and also to size WAN bandwidth for the replication of nightly incremental backups.
Pricing and Availability
WD Arkeia fourth generation network backup appliances – models RA4300, RA4300T, RA5300, RA6300 – will be available in July 2013 through select DMR’s and WD-authorized value-added resellers (VARs) in the US, Canada, and Europe. Manufacturer’s Suggested Retail Price, including hardware and software, begins at $9,990 USD. WD Arkeia network backup appliances are covered by one year of unlimited access to technical support, one year of software updates, and a one-year limited hardware warranty.
Subject: Storage | June 20, 2013 - 07:40 PM | Jeremy Hellstrom
Tagged: LAMD Amber, corsair, neutron gtx
Corsair's Neutron GTX has 240GB of 19nm MLC NAND with a LAMD Amber controller, similar to the previous model but with process shrunk RAM. Write speeds do suffer from the new flash, but that will only be noticeable during large file transfers not during normal usage scenarios. On the other hand [H]ard|OCP noticed many performance increases which were due to the LAMD Amber controller and netted this drive a Silver award. The SSD market is very large, with many makes and models available; this drive is worth putting on your short list.
"Corsair moves to a smaller 19nm Toshiba Toggle MLC NAND with its LAMD-controlled Neutron GTX Series of SSDs. This shrink comes amongst stiff competition from other manufacturers, and a new SSD that is very similar to the Neutron GTX. Today we see how the new GTX stacks up against its increased competition."
Here are some more Storage reviews from around the web:
- SanDisk Extreme II 240 GB SSD Review @ OCC
- Hardware.Info tests lifespan of Samsung SSD 840 250GB TLC SSD
- HGST SSD800MM SAS 12Gbps SSD and LSI SAS 9300-8e HBA @ SSD Review
- OCZ Vertex 450 256GB SSD Review @ Hardware Canucks
- TCS BGADrive SSD @ SSD Review
- SanDisk Extreme II 240GB SSD @ Kitguru
- Toshiba THNSNH 256 GB SSD @ techPowerUp
- Intel SSD DC S3500 Review (480GB) @ AnandTech
- Samsung 840 Pro and Samsung 840 Solid State Drives @ X-bit Labs
- Intel DC S3500 480GB SSD Review @ HCW
- Intel DC S3500 Data Center SSD Review (480GB x 4) @ SSD Review
- OCZ Vertex 3.20 240GB SSD Review @ Hardware Canucks
- Lexar Professional USB 3.0 Dual-Slot Reader @ techPowerUp
- Patriot Supersonic Magnum 256GB USB 3.0 Flash Drive Review @ OCC
- Mushkin Enhanced Ventura Plus Series 16GB USB 3.0 Flash Drive Review @ Madshrimps
- Kingston DT HyperX Predator 512GB USB 3.0 Flash Drive @ Funkykit
- Synology DiskStation DS1513+ @ Legion Hardware
- Synology DiskStation DS1813+ @ Kitguru
- Startech.com S2510U2W review: WiFi disk @ Hardware.info
- ASUSTOR AS-604T NAS Network Storage Server @ Benchmark Reviews
- Buffalo DriveStation DDR3 review: external disk on steroids @ Hardware.info
- QNAP TS-421 4-bay Home & SOHO NAS Review @ Madshrimps
Subject: General Tech, Storage | June 12, 2013 - 08:04 PM | Ken Addison
Tagged: ultrabook, sandisk, Samsung, pci-e ssd, Marvell, MacBook Air, macbook, haswell, apple
As Scott covered earlier this week, Apple quietly announced an update to the MacBook Air line along side the headline-grabbing Mac Pro redesign preview. Being a MacBook Air user for the past 2 years, I decided it was time to replace my Sandy Bridge-based model with some new Haswell goodness. Today marked the first day of retail store availability, and I picked up an 11" model with 256GB SSD.
Naturally, when I got back to the office there was only one route to take, installing Windows and disassembling it. While Anand uncovered the fact that these MacBooks were hiding a new unadvertised option, in a PCI-Express based SSD, I wanted to check it out for myself.
When I did some digging, I discovered that while Anand found a Samsung based SSD in his MacBook, mine actually contained a model by Sandisk. I did a quick initial benchmark in OS X, and proceeded to inspect the hardware itself.
Subject: Storage | June 11, 2013 - 08:08 PM | Jeremy Hellstrom
Tagged: Seagate, NAS
CUPERTINO, Calif.--(BUSINESS WIRE)-- Seagate Technology (NASDAQ:STX) today took the wraps off its new Seagate® NAS HDD—a cutting-edge drive custom-built for always-on, one- to five-bay network attached storage (NAS) systems. Engineered with performance and reliability in mind, the new drives are available in multiple capacity points including a 4TB option—the industry’s highest capacity NAS hard disk drive (HDD) solution available—and strong industry support from nine NAS system partners.
“Today about 50 percent of NAS arrays are sold diskless meaning that customers are challenged with identifying and installing the right storage for their system. By developing a drive like NAS HDD, we’ve taken the guesswork out of it and made it easy for customers to identify the right drive for their system,” said Scott Horn, Seagate vice president of marketing. “By collaborating closely with a variety of partners who specialize in NAS systems, we’re making what was a confusing effort into a plug-and-play one.”
Featuring up to 4TB of storage the drive now enables NAS systems, such as those utilized in homes and small to midsize businesses (SMB), to provide up to 20TB of data in a five-bay NAS array. And with over 30 percent capacity improvement over competitive offerings, the NAS HDD 4TB drive delivers the highest capacity available on the market.
Cost effective drives built specifically for NAS solutions, the 4TB option has the capacity to store over 819,000 photos, 1 million songs or nearly 500 hours of high-definition (HD) video content—more than enough space for the average household. It is also ideal for small businesses with large enough capacities to support CAD files, medical images and databases.
“QNAP is thrilled to be teaming up with Seagate to offer our customers a high-performance storage solution optimized for NAS systems,” said Meiji Chang, general manager of QNAP. “The Seagate NAS HDD allows us to deliver the highest capacity storage offering on the market while providing our customers with a huge boost in performance and a reliable business level NAS solution for 24x7 operations.”
“Households and SMBs continue to generate a significant amount of data, and need fast and reliable storage solutions,” said John Rydning, IDC's research vice president for hard disk drives. “Rather than taking hours or days to transfer a large amount of digital content over the internet to a cloud storage service provider, Seagate’s new NAS HDD provides a high-capacity solution for fast data transfers and backups on-premise over local networks.”
Built to provide up to 10 percent performance advantage over the competition for 24x7 NAS applications, the NAS HDD is engineered for performance in always on applications and can support multiple HD video streams and user profiles. The drive boasts near silent acoustics operating below the range of audible sound for the human ear with as low as 1.9 bels, providing optimized acoustics for the home or SMB environment. It also features Seagate’s own NASWorks™ technology which improves drive reliability by supporting features that limit drive vibrations and support extended error recovery controls for better data integrity.
Seagate NAS HDDs are built and tested to provide industry-leading performance for small NAS systems. Key features of the NAS HDD include:
- Industry’s Highest Capacity NAS Drive—up to 4TB available, the NAS HDD offers a 30 percent capacity advantage over the competition.
- Best Performance for 1- to -5-bay NAS Systems—built and tested to provide industry-leading performance, NAS HDDs offer the industry’s highest throughput to deliver the performance demanded by NAS solutions.
- NASWorks—supports error correction via customized error recovery controls, power management and vibration tolerance for optimal performance and reliability in a 1- to 5-bay solution.
- Improved Vibration Tolerance—dual-plane balance supports the unique weighted motor design minimizing vibration that can be amplified in multi-drive systems improving the drive’s performance and system reliability.
- Advanced Power Management—supports multiple user-selectable power profiles that can optimize power usage for different workloads to minimize power consumption while maintaining high-availability performance.
- Quiet Drive Operation—enhances the end customer experience with near-silent acoustics for low-noise environments like living rooms or office spaces.
Designed with compatibility in mind, Seagate NAS hard disk drives have been rigorously tested by some of today’s top NAS providers and flawlessly integrated into their NAS solutions. For more information on the Seagate NAS HDD and qualified OEM partners please visit www.seagate.com/www/nashdd.
Subject: Storage | June 7, 2013 - 06:38 PM | Jeremy Hellstrom
Tagged: sandisk, Extreme II series, marvell 9187, 19nm, mlc
SanDisk claims their Extreme II can run at 550/510 MB/s sequential read/write, and 95,000/78,000 for random read/write IOPS, a claim which [H]ard|OCP just put to the test. The two major changes to this drive that will contribute to the difference in speed are the switch from a Sandforce controller to the Marvell 9187 controller and the MLC flash which is 19nm in this drive. Testing shows that the drive does live up to expectations though they did point out the lack of encryption as a weakness. Prices for the drives are around the magic $1/GB mark, making this drive a solid contender in a very populous market.
"SanDisk releases its Extreme II series SSD, which features the Marvell 9187 controller in concert with 19nm eX2 ABL MLC NAND. The competition is heating up as another manufacturer with massive foundry capabilities releases a new SSD. Will the Extreme II "blaze through your day" and "keep you ahead of deadlines?"
Here are some more Storage reviews from around the web:
- SanDisk Extreme II Series 120GB, 240GB and 480GB SSD Review @ Legit Reviews
- Seagate 600 240GB SATA III 6Gbps SSD Review @ Legit Reviews
- OCZ Vertex 3.20 240GB SSD Review @ HiTech Legion
- Crucial M500 480GB SSD Review @ Hardware Canucks
- LSI SandForce Next Gen SSD Controller With 1800MB/s Speeds Discovered at Computex @ SSD Review
- Seagate's 600 SSD solid-state drive @ The Tech Report
- KingFast E-Drive KF2510SCF 120GB 2.5" SATA 3 SLC SSD Review @ ModSynergy
- KingFast E-Drive 2.5'' SATAIII SLC 120GB SSD Review @ Madshrimps
- OCZ Vertex 3.20 240GB SSD review: Vertex 3 with 20nm flash @ Hardware.info
- ADATA DashDrive Elite UE700 64GB USB 3.0 Flash Drive @ eTeknix
- Zalman U3M32 32GB SLC USB 3.0 Flash Drive @ Funkykit
- Seagate's Desktop HDD.15 4TB hard drive @ The Tech Report
- Seagate Constellation ES 1TB Hard Drive Review @ PCSTATS
- Adaptec (by PMC) ASR-72405 RAID Controller (X2) Review - 1M IOPS & 12GB/s Thru 24 SMART Optimus SSDs @ SSD Review
- Vantec NexStar WiFi Hard Drive Dock Review @ Legit Reviews
- ioSafe N2 NAS / RAID Storage Solution Review @ OCIA
- Synology DS713+ NAS @ TechwareLabs
- QNAP TurboNAS TS-221 NAS Server @ NikKTech
- Infortrend EonNAS Pro 510 Review @ TechwareLabs
Subject: Storage | June 3, 2013 - 09:59 PM | Tim Verry
Tagged: super talent, ssd, mx3, computex 2013, computex
San Jose-based storage manufacturer Super Talent has announced its new UltraDrive MX3 SSD. This new drive is the successor to the existing UltraDrive MX2, and is allegedly twice as fast. In an interesting twist, Super Talent is releasing the MX3 in both MLC and SLC flavors, to serve the consumer and enterprise markets simultaneously with the same branded drive and controller.
The MX3 is a SATA 3 6Gbps drive that is rated at 500MB/s reads and 400MB/s writes. The MLC version will come in capacities ranging from 64GB to 512GB while the SLC flash SKUs top out at 256GB. The chart below details the model numbers at each capacity point for both the MLC and SLC SKUs, depending on what you need.
In the press release, Super Talent CEO Abraham Ma stated the following:
“We are excited to introduce the MX3. Not only does it offer a considerable upgrade in speed from its predecessor, the MX2, it is also an extremely reliable device that we believe fits the needs of our OEM and consumer customers.”
Pricing and availability have not been announced, however.
Stay tuned to PC Perspective throughout the week for more Computex 2013 news.
Subject: Storage | June 3, 2013 - 08:15 AM | Allyn Malventano
Tagged: western digital, wdc, Blue, 7mm, 1TB
Looking at the new spec sheet, the new 1TB Blue carries increased cache (16MB) and reduced Drive Ready time (2.8 sec) as compared to their previous 9.5mm 1TB models.
Press blast after the break.
Subject: Storage | May 28, 2013 - 01:47 PM | Jeremy Hellstrom
Tagged: ssd, crucial m500, mlc, marvell 9187, RAIN
Before discussing the impressive price point of Crucial's M500 drive their are two features worth mentioning about this drive, RAIN and the Marvell 9187 controller. RAIN is Redundant Array of Independent NAND which offers data parity which will allow you to successfully recreate data after an uncorrectable error, something which might put the minds of those still leery of SSDs to rest. The new Marvell controller is the secret to the pricing of this drive, it allows the usage of 128Gbit (16GB) NAND dies as opposed to the more common 64GBit dies and is produced at a lower cost than other controllers. [H]ard|OCP tested the 512GB drive and does warn that the specifications of the two smaller capacity drives are different enough to require individual testing. However as you can pick up the 512GB drive for $400 you might simply opt for the largest drive which offers competitive performance at an amazing $0.78/GB.
"Crucial's M500 offers the lowest price per gigabyte for an MLC SSD with enterprise-class features not seen on typical consumer SSD data drives. With new 128Gbit MLC NAND paired with the Marvell 9187 controller the M500 should deliver great performance at a historically low price point. Is the Crucial M500's performance up to par?"
Here are some more Storage reviews from around the web:
- 240GB OCZ Vertex 3.20 Solid State Drive @ Benchmark Reviews
- OCZ Vertex 3.20 120GB SSD Review @ Techgage
- Solidata K8 1920E SSD Review - SandForce Driven and an Amazing 2TB Capacity @ SSD Review
- OCZ Vertex 3.20 Solid State Drive @ X-bit Labs
- OCZ Vertex 3.20 240GB SATA III 2.5'' SSD Review @ Madshrimps
- OCZ Vertex 450 256GB SSD Review @ Legit Reviews
- OCZ Vertex 450 SSD @ Techspot
- OCZ Vertex 450 @ Hardware.info
- OCZ Vertex 450 SSD @ SSD Review
- OCZ Vertex 450 256GB @ Tweaktown
- SanDisk Ultra Plus 256GB SSD @ eTekinx
- Samsung SSD 840 comparison @ Hardwareoverclock
- Seagate 600 Pro SSD @ SSD Review
- Crucial M500 480GB SSD @ eTeknix
- Bang for Your Buck: Best 256GB Class SSD's under $200 @ Tweaktown
- OCZ Vertex 3.20 240GB Solid State Drive Review @ OCIA.net
- Kingston SSDNow E100 Enterprise SSD @ Tweaktown
- Mushkin Chronos GO Deluxe 1.8″ SATA 3 SSD Review ? Lightning Speeds Ultrathin Design @ SSD Review
- HGST Travelstar 7K1000 1TB 2.5" Hard Drive @ Tweaktown
- 4TB Seagate Desktop HDD ST4000DM000 @ Benchmark Reviews
- WD Se 4TB Enterprise Hard Drive Review @ Techgage
- Western Digital Scorpio Blue (WD5000LPVT) 500GB HDD @ Tweaktown
- Seagate Laptop Thin SSHD 500GB review: 2.5-inch hard disk with SSD cache @ Hardware.info
- Seagate Desktop HDD.15 4TB Hard Drive Review @ Hardware Canucks
- ADATA DashDrive Elite UE700 USB 3.0 Flash Drive @ Tweaktown
- Kingston DT Workspace 64GB 'Windows To Go' USB 3.0 Flash Drive @ Tweaktown
- Adata DashDrive Elite UE700 32GB Flash Drive Review @ Ninjalane
- Kingston HyperX Predator 512GB @ Hardware.info
- 32 32/64GB USB 3.0 memory stick test: lots of differences @ Hardware.info
- Patriot Supersonic Magnum Flash Drive @ Benchmark Reviews
- Lexar Professional 128GB Compact Flash Memory Card @ Tweaktown
- Transcend 32GB Wi-Fi SDHC @ Tweaktown
- Kingston 64GB microSDXC SDCX10/64GB @ Bjorn3D
- WD My Passport Ultra 1TB Portable Storage Drive Review @ Legit Reviews
- ADATA DashDrive Air AE400 Wireless Storage Reader and Power Bank Review @ Madshrimps
- Rosewill RDEE-12002 USB 3.0 Hard Drive Enclosure @ techPowerUp
- Corsair Voyager Air 500GB Wireless Storage Device @ Tweaktown
- Transcend StoreJet Cloud 32GB Wireless Storage Device @ Tweaktown
- Kingston MobileLite Wireless Review @ Pro-Clockers
- Synology DS213j review: deluxe entry-level NAS @ Hardware.info
- Icy Dock FlexCage MB975SP-B 5x3.5" in 3x5.25" HDD Cage Review @ Hi Tech Legion
- Shuttle OMNINAS KD20 @ techPowerUp
- iStarUSA BPU-340SATA Military Grade Drive Enclosure @ NikKTech
- LaCie CloudBox 1TB Personal NAS @ Tweaktown
Subject: Storage | May 28, 2013 - 08:15 AM | Allyn Malventano
Tagged: Xe, western digital, wdc, se, RE, hdd
Today Western Digital did a slight rearranging of their enterprise product lineup:
Starting from the top down, the Xe series is essentially a SAS version of their 2.5" 10k RPM VelociRaptor form factor, available in 300GB, 600GB, and 900GB capacities. The Re series is the same 'RE' we are all familiar with, and is now available in both SAS and SATA. That bottom block, however, is something new:
The Se series is Western Digital's attempt at a lower cost Re series drive, and will be available in capacities up to 4TB.
So the Se is an Advanced Format version of the Re, designed for reduced workloads. Throughput is slightly reduced due to differences in track geometry, though WD let me know they expect final shipping Se's may be closer to the Re spec than the slide indicates. The Se carries the same RPM as well as StableTrac (where the spindle is supported at both ends), RAFF (where accelerometers compensate for chassis vibration), and TLER (where IO request timeouts are adjusted to play nicely with hardware RAID).
The key to the success of the Se will be just what sort of reduced cost Western Digital is able to price the drive at. That information, as well as a full review of an Se, will be coming later today, just as soon as our next batch of samples arrives.
Subject: Storage | May 21, 2013 - 10:01 PM | Tim Verry
Tagged: hgst, western digital, 500GB platter, 1.5tb drive, mobile hard drive
Hitachi Global Storage Technologies (HGST, which is now owned by Western Digital) has developed a new 2.5” mobile hard drive called the Travelstar 5K1500. The hard drive uses three 500GB platter drives for a total capacity of 1.5TB. HGST claims that the drive is the highest capacity 9.5mm mobile drive on the market. Additionally, the company has stated that the new drive is faster than its existing two-platter hard drives according to the PCMark Vantage and PCMark 7 benchmark suites.
The 1.5TB Travelstar 5K1500 is a 5400 RPM hard drive with 32MB of on-board cache, a 6Gbps SATA III interface, and shock protection features.
The new mobile drive will be used in external hard drives, all-in-one systems, and notebooks where storage space is valued more than pure performance. It will be available sometime in June for an as-yet-unannounced price point. Another version of the Travelstar 5K1500 that offers automatic encryption of data will be available in Q3 2013.
Subject: Storage | May 14, 2013 - 05:53 PM | Jeremy Hellstrom
Tagged: sshd, cache, western digital, Black SSHD, Hybrid Drive
The Tech Report sat down with Matt Rutledge, Vice President of Western Digital's client computing group to discuss the software behind their new HDDs with an SSD cache. Sandisk will be providing the hardware and WD who will be providing the custom caching software which will not be coded into the hardware but will function at the driver level. Matt mentioned that this software can also make use of the system's memory and incorporate it into the cache as well though it was not completely clear if there will be many user editable settings. Check the interview out.
"WD revealed that its hybrid drives will use SanDisk iSSD flash components. The announcement was devoid of details on how the caching system works, but we can now shed new light on the software-managed scheme."
Here are some more Storage reviews from around the web:
- Seagate SSHD Thin 500GB Review @ Hardware Canucks
- Seagate Desktop HDD.15 4TB vs WD Black 4TB Hard Drive Review @ Legit Reviews
- Toshiba MK3001GRRB 300GB SAS 6Gb/s HDD @ NikKTech
- Intel 525 Series 120GB & 180GB mSATA SSD @ Hardware Canucks
- PNY Prevail Elite 240GB SSD @ Tweaktown
- Crucial M500 480 GB @ techPowerUp
- 120GB OCZ Vertex 3.20 Solid State Drive @ Benchmark Reviews
- Seagate Desktop HDD.15 4TB Review @ Techgage
- Crucial M4 256GB SATA III SSD Review @ PCSTATS
- Corsair Neutron 128GB and 256GB (2013 Hynix Edition) @ TweakTown
- Kingston Wi-Drive 64GB @ Kitguru
- Western Digital My Book Live 1TB Personal Cloud Storage @ Tweaktown
- OWC Envoy Pro EX USB 3.0 Bus-Powered Portable SSD @ SSD Review
- PQI Tiffany 32GB USB 3.0 Flash Drive @ Tweaktown
- 64 GB Kingston DataTraveler Ultimate 3.0 G3 Flash Drive @ TechARP
- Kingston DataTraveler Ultimate 3.0 G3 32GB Flash Drive Review @ Legit Review
- Patriot Supersonic Magnum 256GB USB 3 Flash Drive @ SSD Review
- PQI i-mini USB 3.0 32GB @ techPowerUp
- LSI MegaRAID 9271-8i PCIe Raid Controller @ Funky Kit
- Icy Dock FlexCage MB975SP-B Tray-Less 5 x 3.5" HDD Dock @ Tweaktown
- SilverStone DS322 Dual-Bay RAID Enclosure @ Tweaktown
- Western Digital My Passport Enterprise 500GB USB3.0 External Hard Drive @ eTeknix
Subject: Storage | May 10, 2013 - 03:48 PM | Tim Verry
Tagged: ramdisk, ram drive, ram, radeon ramdisk, amd
In light of AMD’s latest memory release and Radeon RAMDisk push, I decided to take a look at the latest version 4.1.0 of the RAMDisk software to see what had changed since the last time I tested it out. Improved installation and logging along with a couple of new features are all part of the new RAMDisk software.
AMD has simplified the installer since the previous version to the point that only a few clicks are necessary to get setup. Although you can jump into the advanced settings and change the installation path, the default options are basically just to accept the ToS and click next. Other GUI tweaks include a new Logging tab that scans the last 1,000 entries in the Windows Event Log and shows only those related to the RAM Drive.
The biggest change is the addition of new options in the load/save tab. Because of the nature of RAM, the RAMDisk created by the software is not persistent across reboots. However, you can save the disk image to a file on persistent storage (a hard drive, SSD, et al). Then, you can save the RAM Drive and its contents to a file and reload that disk after a restart.
The paid version of Radeon RAMDisk takes this a step further by allowing background updating of the RAMDisk data. With the Load in Background option, the RAMDisk will be immediately available to the operating system after a restart. The software will automatically start transferring data from the image stored on the hard drive to the portion of RAM set aside for the RAM disk instead of making the user wait fro the entire disk to be recreated before it can be accessed. Any data requested that has not yet been transferred to the RAM disk will be transparently pulled from the hard drive image.
Further, AMD offers up a background update option that will run in the background and continuously write RAMDisk changes to the *.img file stored on the hard drive. This eliminates the need to wait for the entire RAMDisk to be written to disk before shutting down the computer or stopping the RAM Drive. Considering the wait times to read and write data from/to the hard drive is one of the major limitations of RAM drives, this is a really useful feature that certainly adds some incentive to springing for the paid version.
The free version doesn’t get background updating, but it does still have the AutoSave feature that will write data out to the image file periodically which will help prevent data loss due to power failure or kernel panic.
Heh, the SSD is pegged but the RAMDisk utilization peaked at 4% when copying a 1.51GB Kerbal Space Program (with a few mods installed) folder from an Intel X25-M to a 4GB RAMDisk ;).
In my brief testing yesterday, I had some trouble getting the software to create a FAT32 formatted disk, where it kept changing to unformatted before creating the disk. Eventually I opted to format the drive myself using Windows’ Disk Management utility. Aside from that hiccup, I think the new version is worth updating to if you have not already--especially if you have the paid version (so that you can get the background data transfer features).
For specific details on exactly what has changed, an AMD-provided change log is below:
Feature Highlights of AMD Radeon™ RAMDisk release 4.1
- Updated GUI improvements .NET
- Updated installer package – Fewer clicks required to install
- Improved GUI event logging
- Improved management of options when setting Load/Save
Performance Highlights of AMD Radeon™ RAMDisk release 4.1
- Performance gains on AMD Radeon™ RAMDisk 32GB and 64GB
- Vastly improved load and save mechanics allowing for background update and background loading of the RAMDisk. Reduces wait times for load and save. “Background Update” and “Load in Background” enabled (registered users only)
- Faster PC startup and shutdown while RAMDisk is enabled.
Improved IO performance on multi-processors and multi-core systems
- Evenly distributed load among the CPUs. Allows for more system efficiency.
Subject: Storage | May 7, 2013 - 06:31 PM | Tim Verry
Tagged: x8 accelerator, virident, ssd, seagate 1200, Seagate, pci-e
In addition to its recently-announced 600 and 600 Pro consumer line of solid state drives, Seagate has unveiled two new drives aimed at the enterprise SSD market. The Seagate 1200 series is a 2.5" SAS SSD and the Seagate X8 is a PCI-E based accelerator card.
Unfortunately, details are extremely scarce on both upcoming enterprise drives. Performance, specifications, pricing, and availability are still unknown. Seagate has officially confirmed there existence and shared a few tidbits of information, however.
The Seagate 1200 SSDs are 2.5" form factor drives with a 12Gbps SAS interface, which suggests that they will be at least somewhat faster than the consumer versions due to Seagate implementing the faster drive interface. The most important detail however, is that Seagate will be using its own custom SSD controller in the 1200 series. The new controller is still a mystery, but it is developed by Seagate and not Link A Media with customized firmware like the 600 and 600 Pro drives. I am especially interested to find out more about this aspect of the drive. Hopefully the new controller is successful and will trickle down to the company's next-generation consumer SSDs.
Meanwhile, Seagate's X8 Accelerator card is a half-height, half-length expansion card with up to 2.2TB of flash memory. The new PCI-E based drive is based on technology from Virident and can be used to accelerate applicators or database operations in servers. It will be available in capacities ranging from 550GB to 2.2TB. The SSD controller/management duties are handled by the host system's CPU and maintenance operations like garbage collection can be scheduled for periods of downtime when the server is not being hit hard by things like database requests for a popular web application. According to Seagate, each X8 Accelerator will be capable of up to 1.5 million IOPS.
Both of the new enterprise solid state drives will be released later this year.
Seagate has officially moved into the solid state drive (SSD) market with two new consumer drives: the 600 and 600 Pro series. The new drives come in capacities ranging from 100GB to 480GB. Both series utilize the Link A Media (LAMD) LM87800 SSD controller and 19nm 2-bit per cell MLC NAND flash from Toshiba. Seagate has not provided pricing or availability dates, but pricing should be in-line with existing drives, and reviews are already available around the Internet.
The Seagate 600 series is the lowest-tier solid state drive. It will be available in 120, 240, and 480GB capacities. Seagate is using 128GB, 256, and 512GB of NAND flash on 2, 4, and 8 channels respectively. In addition to the LM87800 SSD controller (which features custom Seagate firmware) and NAND flash, Seagate is including 1MB of DDR2-800 DRAM per 1GB of NAND flash for a total of 128, 256, and 512MB of DRAM on the 120, 240, and 480GB capacity drives.
The 600 Series is rated at up to 500MB/s peak 128KB reads and 400MB/s writes (limited to 300MB/s on the lowest-capacity 120GB drive). Further, Seagate states that the 120GB drive is capable of 80,000 random read and 60,000 random write (4K) IOPS, while the 240GB and 480GB drives can reach up to 80,000 random read and 70,000 random write (4K) IOPS.
Also note that the 600 series comes in both 7mm and 5mm form factors, which makes it compatible with most laptops. Seagate provides a 3 year warranty on the 600 series.
The Seagate 600 Pro series steps things up a notch by adding overprovisioning, capacitors for power-loss protection, and a longer 5 year warranty. The 600 Pro series will come in 100, 120, 200, 240, 400, and 480GB capacities. The 100, 200, and 400GB versions of the SSD offer additional overprovisioning which gives the SSD controller more space to work with. The capacitores are intended to provide enough power in the event of a PC power loss to write all data to the NAND flash and prevent data loss.
The 600 Pro drives offer the same 6Gbps SATA interface, LM87800 controller, and 1MB-to-1GB DRAM to NAND ratio. The Pro drives do not come in the 5mm high form factor, so laptop compatibility is limited.
Further, the 600 Pro Seagate SSDs are faster drives. According to Seagate, the Pro series offers up to 85,000 and 30,000 random read and write (4K) IOPS on the overprovisioned drives and p to 85,000/11,000 random IOPS on the 240 and 480GB drives. The 100 and 120GB drives are slower than the other drives though due to less NAND flash and channels between the flash and controller. The chart below details the rated specifications for all of the announced drives.
|Series||600 Pro||600 Pro||600 Pro||600 Pro||600 Pro||600 Pro||600||600||600|
|Random 4K r/w KIOPS||80/20||80/8||85/30||85/11||85/30||85/11||80/60||80/70||80/70|
|128KB r/w sustained sequential||>500/>300||>500/>400||>500/>400|
|128KB peak sequential r/w||520/300||520/300||520/450||520/450||520/450||520/450|
Blank areas indicate that rated specifications were not available.
Fortunately, the reviews available online (such as AnandTech's) do seem to support the new drives as far as performance is concerned. The drives are stacking up nicely versus the competition, which is interesting given the controller choice. For example, the sequential read speed looks promising.
The 600 and 600 Pro drives are looking like solid drives so long as the pricing is competitive. I'm excited to see where Seagate goes from here.
Subject: Storage | May 3, 2013 - 07:32 PM | Jeremy Hellstrom
Tagged: LAMD, corsair, neutron, ssd, asynchronous NAND, 22nm
Still featuring the Link_A_Media Devices LM87800 controller but with all new 22nm SK Hynix Synchronous NAND the refreshed Corsair Neutron SSD series just arrived on [H]ard|OCP's test bench. The refresh brings both good and bad attributes, while the 22nm NAND proves a little slower than the original 25nm it also brings a much lower price. That lower price paired with a 5 year warranty should make this drive attractive to users that are holding off on picking up an SSD because of fears that the drive will stop functioning in a few years, or who have a hard time spending well over $1/GB for storage.
"Corsair keeps pace with continuing innovation in the NAND market by switching from 25nm IMFT NAND to the rarely seen 22nm SK Hynix NAND. This NAND provides a lower price point and extra capacity. Today we take a look to see if the Neutron Series performance remains and how this new SSD build stacks up to the competition."
Here are some more Storage reviews from around the web:
- ADATA XPG SX900 128GB SSD Review Redux @ [H]ard|OCP
- Crucial M500 480GB Solid-State Drive Review @ Legit Reviews
- Comay Pluto SC3 Enterprise SSD @ Tweaktown
- ASUS RAIDR Express 240GB PCI-Express SSD review: is this the future? @ Hardware.info
- Corsair SSD Toolbox Software Overview - Better than Never @ Tweaktown
- Top SSD Recommendations For May 2013 - Samsung TLC Dethrones the SanDisk SSD Family @ SSD Review
- The SSD Optimization Guide Ultimate Windows 8 (And Win7) Edition @ The SSD Review
- OCZ Vertex 3.20 240GB SSD w/20nm Flash @ FunkyKit
- OWC Mercury Accelsior E2 PCIe SSD @ SSD Review
- Transcend MSA720 128GB mSATA SSD Review @ Legit Reviews
- Seagate Laptop Thin SSHD 500GB Review @ Techgage
- SanDisk Extreme Pro 128GB Compact Flash Memory Card @ Tweaktown
- ADATA DashDrive Air AE400 Wireless Storage @ Benchmark Reviews
- takeMS LumX 4GB USB Flash Drive Review @ Madshrimps
- SanDisk Extreme Pro SDHC and microSDHC Memory Card @ Tweaktown
- Corsair Flash Survivor Stealth 64GB USB 3.0 Flash Drive @ Tweaktown
- ADATA DashDrive Durable UD310 32GB USB 2.0 Flash Drive @ eTeknix
- Synology DS213+ High-Performance 2-Bay NAS Server for SMB Review @ Madshrimps
- Corsair Voyager Air 1TB Wireless Hard Drive @ eTecknix
- Patriot Supersonic Rage XT 64GB Flash Drive @ FunkyKit
- Mach Xtreme MX-ES 32GB USB 3.0 Flash Drive @ Tweaktown
- Transcend Wi-Fi SD Card @ Hardware.info
- PQI Air Bank 500GB External Wi-Fi Hard Disk Drive @ Tweaktown
- Asustor AS-604T 4-Bay NAS @ Tweaktown
- QNAP's TS-EC1279U-RP 12-bay Flagship Rackmount NAS @ AnandTech
- nfortrend EonNAS Pro 510 NAS @ Tweaktown
- Asustor AS-606T @ Legion Hardware
Today Western Digital launched their new 5mm 2.5" Blue. This model will only come in 500GB. Capacity options are limited presumably due to a single 500GB platter, which is about all you can fit into a housing that's only 5mm thick.
The drive launches at an MSRP of $89.00, but don't rush out to buy one just yet. The new drive will require a purpose-built installation, as it uses a new SFF-8784 edge connector to receive data and power from the host system. You're basically going to need a laptop that has a bay designed for just this drive, which may take a while.
Today Western Digital launched a new line of Hard Disk Drives. The Xe is very similar to their VelociRaptor, with the same 2.5"-3.5" heat sink adapter plate. The primary difference, however, is these units feature Dual Port SAS connectivity.
The new drives feature a 5-year warranty and will come in 300, 600, and 900GB capacities. With SAS HDD's becoming scarce lately, there is a definite gap developing in existing legacy SAS systems. We're glad to see a lower power SAS-connected 10,000 RPM offering to help bridge that gap.
Subject: Storage | April 19, 2013 - 07:20 PM | Jeremy Hellstrom
Tagged: sshd, Seagate, Hybrid Drive, 500gb
We have seen many hybrid drives come and go, most of which only benefited desktop users who were accessing certain files often enough that they were cached on the flash memory. Seagate has introduced a new iteration of the SSHD specifically for laptops, uniting 500GB of 5400 RPM platter based storage with 8GB of MLC NAND and a 64MB cache which [H]ard|OCP recently benchmarked. They didn't forget desktop users as they released 1TB and 2TB models at 7200 RPM but it is the laptop version which is perhaps more interesting as not many models allow the installation of a second drive like desktops do. The testing results were mixed, with several obvious benefits interspersed with odd performance changes after multiple runs, however the small price differential between a standard HDD and a SSHD might just convince you to pick up this new breed of hybrid drive.
"Seagate has introduced the next generation of Solid State Hybrid Drives, commonly referred to as "SSHD." These drives use a small amount of MLC NAND to accelerate the performance of a 5400 RPM spinning disk. Today we test the mobile version against other available SSD caching solutions."
Here are some more Storage reviews from around the web:
- Crucial's M500 SSD @ The Tech Report
- SuperSSpeed S301 Hyper Gold SLC Enterprise SSD @ Tweaktown
- Consumer (Samsung and OCZ) vs. Enterprise (SMART Optimus) SSD Performance Analysis @ SSD Review
- Hardware.Info tests lifespan of Samsung SSD 840 250GB TLC SSD
- Kingston SSDNow V300 240GB SSD Review @ Hardware Canucks
- ADATA XPG SX900 128GB with SandForce B02 controller SSD @ Tweaktown
- SMART Storage Systems CloudSpeed 500 Enterprise SSD @ Tweaktown
- Samsung SM843 Enterprise SSD Review (240GB) @ SSD Review
- Plextor M5M (256GB) mSATA @ AnandTech
- Samsung PM841 512GB mSATA SSD @ SSD Review
- Intel 525 120GB mSATA SSD @ Hardware.info
- Thermaltake BlacX Duet 5G USB 3.0 Docking Station @ Tweaktown
- Seagate Backup Plus 1 TB Portable Hard Disk Drive @ TechARP
- ADATA DashDrive Elite UE700 USB 3.0 Flash Drive Review @ Pro-Clockers
- ICY DOCK MB662U3-2S Dual Bay USB 3.0 RAID Enclosure @ Tweaktown
- Icy Dock ICYRaid MB662U3-2S Dual-HDD Enclosure Review @ Hi Tech Legion
- Infortrend EonNAS Pro 510 @ Legion Hardware
- Asustor AS 602T @ Kitguru
- QNAP TS879-Pro 8-Bay NAS @ eTeknix
- Thecus N7510 7-Bay NAS @ eTeknix
Subject: Storage | April 19, 2013 - 06:10 AM | Tim Verry
Tagged: trim, ssd, sandforce 2281, sandforce, ROG, raidr, raid, PCIe SSD, asus
ASUS is reportedly adding two new PCI-E Solid State Drives (SSD) to its Republic Of Gamers lineup. Dubbed RAIDR, the new PCI-E SSDs use 19nm Toshiba MLC NAND flash driven by two SandForce 2281 controllers. In turn, the two SandForce drives are put into a hardware RAID 0 configuration for maximum speed. The RAIDR SSD internals are encased in a stylized EMI shield along with a ROG-branded back-plate. In all, ASUS’ RAIDR SSDs measure 157 x 120 x 20mm.
The ASUS RAIDR drives show up as a single disk driven by a standard AHCI controller, which allows the two RAID 0 SSDs connected via the PCI-E bus to be boot-able and support the TRIM command. Both RAIDR solid state drives also support Native Command Queuing (NCQ), SMART, Secure Erase, Windows 8 Secure Boot.
According to specifications provided by Sweclockers, ASUS is launching 120GB and 240GB versions of the PCI-E SSDs. Both capacities feature 100,000 IOPS, 128-bit AES encryption, and 620,000 MTBF ratings.
The 120GB RAIDR SSD supports up to 765MB/s sequential reads and 775MB/s sequential write speeds. On the other hand, the 240GB RAIDR drive supports up to 830MB/s sequential reads and 810MB/s sequential writes.
Additionally, ASUS is bundling its RAIDR drives with Kaspersky Antivirus 2013 and a number of ASUS utilities (including SSD TweakIt). The drives should be available sometime next month, but pricing is still unknown. Adding PCI-E SSDs is an interesting move by ASUS that should help the company diversify and expand its ROG branding. Personally, I’m looking forward to seeing how the drives stack up when they are released (and hopefully a PC Perspective review)!