All | Editorial | General Tech | Graphics Cards | Networking | Motherboards | Cases and Cooling | Processors | Chipsets | Memory | Displays | Systems | Storage | Mobile | Shows and Expos
Subject: Cases and Cooling | June 10, 2013 - 11:54 AM | Tim Verry
Tagged: streacom db4, streacom, hsf, Fanless PSU, fanless, cpu cooler
Streacom recently showed off a new cube-shaped case called the DB4. The new case measures 250 x 250 x 250mm (a bit under 10 inches cubed) and doubles as a passive heatsink for internal components.
The Streacom DB4 is a large cube with vertical finned sides that is held aloft by a thin angled bar. The case is intended to be used as the base for a passively cooled desktop PC. Each side of the cube-shaped DB4 case can cool 65W TDP parts, for a total cooling potential of 260W. In addition to being able to cool processors and low-end graphics cards passively, the case also cools the bundled ZeroFlex 250W fanless power supply.
Unfortunately, Streacom is not showing off the internals or detailing how the PC components are connected to the side(s) of the case. When asked for details by Fanless Tech, Streamcom responded that "we will reveal the internal alyout after all patents are through."
Streacom expects to have the case available for sale sometime between late September or early October for 200 Euros. This is a neat case that is not only fanless, but a work of art. I could see myself using this. What do you think about the Streacom DB4?
Subject: General Tech, Cases and Cooling, Shows and Expos | June 7, 2013 - 03:56 PM | Tim Verry
Tagged: seasonic, PSU, m12II evo, m12II bronze, haswell, computex 2013, computex
Following Intel's announcement of new Haswell sleep states, various power supply manufacturers have released compatibility lists detailing which PSUs are able to deliver the low load necessary to support the power sipping sleep states on the 12V rail (which has not been much of a concern until Haswell).
One such PSU manufacturer was Seasonic, who has quite a few Haswell-ready power supplies across several lineups including its Platinum, G, and M12II series, among others. Included in that compatibility list were two new power supplies that Seasonic is showing off at Computex this week: the Seasonic Platinum 1200 and Seasonic M12II Bronze Evo Edition.
SeaSonic Platinum 1200
The Platinum 1200 is a high-end modular power supply that is capable of powering beefy multi-GPU setups. It is 80+ Platinum rated and is up to 92% efficient at 50% load.
Sesonic M12II Bronze Evo Edition
The Seasonic M12II Bronze Evo Edition is an updated version on past models and includes two SKUs that come in at 750W and 850W. It is a fully modular unit with flat black cables and fan control tech. It is 80+ Bronze and Energy Star rated, and is compatible with Intel's 4th Generation Core processors.
Also read: The full list of Haswell-compatible Seasonic power supplies @ PC Perspective.
Subject: Cases and Cooling | June 6, 2013 - 10:31 AM | Tim Verry
Tagged: evga, minibox, mini-itx, gtx titan, gk110, gaming, computex, computex 2013
First shown off at CES 2013, the EVGA Minibox is a small form factor chassis for Mini-ITX systems that can accommodate large graphics cards. EVGA has managed to enable users to pack a lot of hardware into this tiny form factor chassis. As a demonstration of the case's capabilities, the company showed off the latest version using a full system build with Core i7-4770K and GTX TITAN interals at Computex this week in Taipei.
The Minibox chassis itself is a dark brushed metal case with two USB 3.0 ports on the front IO and space for a slot loading optical drive. The MiniBox chassis further features a motherboard tray that supports Mini-ITX boards, two 2.5" SATA hard drive bays – and best of all – enough room to install full size GPUs. In order to support lengthy graphics cards, EVGA is including a small form factor 500W power supply that is mounted on the floor of the case..
HEXUS reporters spot the EVGA Minibox at Computex 2013. Look how small it is!
There will be at least two SKUs of the Minibox, depending on whether you want to go with air or water cooling. According to Bit-Tech.net, the air cooled version will use two 92mm fans in the top of the case and one 80mm fan for the bottom-mounted PSU. The water cooled SKU will be slightly larger but have enough room for a water cooling radiator (likely 240mm). Beyond that, details are scarce, but the air cooled version is said to be available as soon as next month with water cooled options becoming available later this year.
The Minibox looks to be one of the better Mini-ITX cases out there (although the price is still unknown), and should be popular among enthusiasts wanting a small box that does not sacrifice gaming potential.
Subject: Cases and Cooling | June 5, 2013 - 07:47 AM | Tim Verry
Tagged: XL-ATX, fractal design, computex 2013, computex, case, arc xl, arc mini r2
Fractal Design is using Computex 2013 to launch two new cases, called the ARC XL and ARC Mini R2. As their names suggest, the ARC XL is a massive brushed aluminum case capable of supporting motherboards up to XL-ATX in size while the ARC Mini R2 is a Micro ATX case that is compatible with Micro ATX and Mini ITX motherboards.
Fractal Design ARC XL
The ARC XL chassis measures 232 x 572 x 552mm and weighs 13.8kg. The full tower case features a texturized aluminum exterior with a clear side window and top-mounted IO panel. The front of the case holds a large mesh grill with white Fractal Design logo. Above the front intake are four 5.25" drive bays. The front IO panel is mounted on the top of the case and includes two USB 3.0 ports, two USB 2.0 ports, audio in/out jacks, and power/reset buttons.
Internally, the ARC XL chassis supports motherboards up to XL-ATX in size, up to eight 3.5" hard drives, and space for two 2.5" solid state drives behind the motherboard tray. In total, the case supports seven 140mm fan positions. Fractal design includes three Silent Series R2 case fans with the chassis. Dust filters in the front, top, and bottom fan vents. Water cooling enthusiasts will be pleased to know that they can install 360mm radiators on top and 240mm radiators in the front of the case (with the hard drive cages removed). Other features include 9 PCI expansion slots, space for a bottom mounted PSU, integrated 3-fan 3-speed fan controller, and space for cable routing behind the motherboard tray.
Fractal Design's ARC XL case will be available in July or early August with an MSRP of $129.95 USD (119.95 EURO).
Fractal Design ARC Mini R2
The ARC Mini R2 is a miniature version of the ARC XL suitable for smaller systems using Micro ATX or Mini ITX motherboards and either water or air cooling.
The Mini R2 has a large mesh grill on the front panel as well as two optical drive bays. The front IO includes two USB 3.0 ports, audio in/out, power and reset buttons, and the fan controller switch. The case measures 210 x 405 x 484mm and weighs 9kg.
Internally, the ARC Mini R2 supports Micro ATX or Mini ITX motherboards, up to six 3.5" hard drives, two 2.5" SSDs (behind motherboard tray), and 4 PCI expansion slots. Graphics cards up to 260mm are supported with the hard drive cage installed, or 400mm with it removed. There is space for cable routing behind the motherboard and water cooling grommets on the back of the case to support external radiators.
Cooling is handled by three bundled Silent Series R2 fans controlled by an included fan controller. The case can support a total of seven fans, including:
- Front: 2 x 120mm (1 included)
- Rear: 1 x 120mm (1 included)
- Top: 1 x 120mm plus 2 x 140mm (1 included)
- Bottom: 1 x 120mm
Watercooling support includes the ability to mount a thin 360mm radiator on top as well as a 240mm radiator over the front intake (with the optical drive and hard drive bays removed respectively). Fractal Design includes removable dust filters over the front, top, and bottom vents.
The Micro ATX ARC Mini R2 will be available for $89.95 (79.95 EURO) in August or early September.
In all, they look like decent cases, though I would have loved to see some additional color options on the ARC Mini R2! (heh).
Subject: Cases and Cooling | June 3, 2013 - 09:08 PM | Tim Verry
Tagged: corsair, computex 2013, computex, carbide air 540, carbide 330r
Corsair is in attendance at Computex 2013 in Taipei, Taiwan this week to show off a number of new products. The latest product announcement is the release and availability of two new Carbide-series cases: the Carbide Air 540 and Carbide 330R.
Corsair Carbide Air 540 Mid Tower Chassis
The Corsair Carbide Air 540 is a dual chamber mid-tower ATX case that is optimized for maximum air cooling performance. The outside of the case is a boxy brushed aluminum affair with a stylized mesh grill running from the top panel to the front panel. The front panel IO ports sit below the two vertically-mounted 5.25” drives, and includes two USB 3.0 ports, two audio jacks, and power/reset buttons.
The case is split up into two chambers and uses the company's “Direct Airflow Path” techniques. The main (left) chamber hosts motherboards up to E-ATX in size along with PCI-E cards and two hot-swap 3.5” (2.5” drive compatible) drive bays. The second (right) chamber holds the ATX power supply, 5.25” drives, and SSD drive bay (which can hold up to four SSDs). The motherboard tray separates the two chambers, but Corsair has added a number of rubber cable routing grommets to aid in cable management and connecting devices in the main chamber to power.
A magnetic (removable) front filter protects the case from dust. Cooling options include up to six 120mm or five 1400mm fans. Water cooling enthusiasts can instead opt for up to a 240 or 280mm radiator on top and a 360mm radiator in the front of the case.
In all, the case measures 16.5” x 17” x 18” (407 x 432 x 457mm). It is available now with a MSRP of $139.99.
Corsair Carbide 330R Mid Tower Case
The other case that Corsair is launching today is the Carbide 330R. This case focuses on quiet operation and utilizes Direct Airflow Path techniques and sound dampening material throughout.
The Carbide 330R is a compact mid tower case clad in brushed aluminum with tapered edges and sharp corners. The front panel has a brushed aluminum front door, two USB 3.0 ports, two audio jacks, and power and reset buttons. Corsair is optimizing this case for low-noise operation by adding sound dampening material on the top, side, and front panels as well as using rubber case feet to reduce noise caused by vibration.
The Carbide 330R supports motherboards up to E-ATX in size, ATX power supplies, four 3.5” (or 2.5”) drives (in tool free trays), and a single 5.25” tool-less drive bay.
Cooling options include:
- 2 x 120mm or 140mm front panel mounts
- 2 x 120mm or 140mm top panel fan mounts
- 1 x 120mm rear fan mount
Users can remove the top panel cover to reveal the two 140mm fan mounts to add a 240mm watercooling radiator though you do lose out on some of the sound dampening potential when you remove that top panel.
The Carbide 330R measures 19.5” x 8.3” x 19” (495 x 210 x 482mm). It is available now with a MSRP of $89.99.
Subject: Cases and Cooling | June 2, 2013 - 12:07 AM | Tim Verry
Tagged: nzxt, mid tower, h230, computex 2013, case
NZXT has kicked off the Computex 2013 coverage with the announcement of a new H230 mid-tower ATX case. Continuing the tradition of the H-series, the H230 is a minimalistic white or black design that incorporates sound dampening material and tool-free internal bays.
The outside of the case is simplistic, with vents and three 5.25” bays on the front. In keeping with the silent intentions, there is no case window here. Brushed aluminum case feet lift the case off of the floor. Two USB 3.0 ports and a single microphone audio jack are available as front IO.
The H230 is constructed of steel with some plastic parts. It measures 195mm x 447mm x 502mm and weighs 7.25kg (approximately 16 lbs.). There are two SKUs, CA-H230I-W1 in white and CA-H230I-B1 in black.
Internally, the H230 mid tower case features tool free drive bays that can accommodate up to 6 3.5” drives and 3 5.25” drives. It can fit GPUs up to 290mm in length with the hard drive cage installed or up to 400mm with the drive cage removed. Heatsinks up to 158mm in height are supported as are motherboards up to full ATX in size (with 7 PCI expansion slots). A bottom mounted PSU slot and cable management routed behind the motherboard tray are also features. Cooling options include up to two 120mm front intake fans, a single 120mm bottom intake fan, and a single 120mm rear exhaust fan. NZXT provides the 120mm exhaust fan with the case. In the press release, NZXT states that “Our designers had one goal in mind while crafting the H230: create an affordable, silent chassis with all of the necessary essentials for a clean, functional build. ”
The new H230 case comes with a 2-year warranty and has an MSRP of $69.99. More information is available on the H230 product page.
The full press release is below:
Subject: General Tech, Cases and Cooling | May 31, 2013 - 05:27 PM | Jeremy Hellstrom
Tagged: antec, haswell, PSU
Antec released two lists today covering the compatibility of both their PSUs and their notebook chargers. If you are worried that your current hardware will not support the new low power states implemented in Haswell check through the list and if your product is listed you are good to go. If not you can treat these as shopping lists for your next PSU or notebook adapter.
Subject: Cases and Cooling | May 29, 2013 - 06:49 PM | Jeremy Hellstrom
Tagged: thermaltake, non-interference cooler, NiC, heatsink
One hurdle many Ivy Bridge owners have to deal with is the proximity of the DIMM slots to the CPU socket as many high end coolers impinge on the space which high DIMMs occupy. This has lead to the adoption of low profile DIMMs or even users removing heatspreaders from their DIMMs in order to have them fit with an installed cooler. Thermaltake is addressing this issue with their new line of NiC heatsinks which do allow the use of full sized DIMMs. This does lead to a taller heatsink, the NiC F4 that ProClockers reviewed is 155 x 140 x 50mm so you should make sure your case is wide enough to accommodate the cooler. The design does not seem to have effected the cooling efficiency of the design, in tests it proved to match the performance of other mid-range coolers.
"Thermaltake’s newest CPU cooler consist of four cooler models for now and the line-up is called the NiC or Non-Interference Cooler series. The reason behind the name is that the coolers allow for the builder or end user to fill all of their motherboard DIMM slots. This is something that is often not possible with most coolers because of their massive size. With that in mind, you can be at ease to know the series allows for maximum ram slot usage. It’s great that we didn't need to fill all the memory slots but it is another issue if we have to sacrifice performance. Well, you don’t have to worry because each of the coolers on this series is rated to a certain wattage level. The Thermaltake NiC F4 model we will be looking at today is rated up to 180 watts of TDP. The other three models are the F3, C4 and C5 and are rated at 160W, 200W and 230W respectively."
Here are some more Cases & Cooling reviews from around the web:
- DeepCool GAMMAXX S40 CPU Cooler Review @ Pro-Clockers
- SilverStone AR01 CPU Cooler Review @ Hardware Secrets
- Phobya Nano-2G 12, G-Silent 12 Slim Edition and NB-eLoop Bionic 120mm Fan Reviews @ eTeknix
- NZXT FZ-200 Airflow Fan Series 200mm fan @ Modders-Inc
- XSPC RayStorm 750 RS240 Water Cooling Kit Review @ Pro-Clockers
- Lamptron CW611 Watercooling Fan Controller @ eTeknix
- Guide: how to install liquid cooling in your PC @ Hardware.info
- Thermaltake Armor Revo Gene Mid Tower Computer Case Review @ Hi Tech Legion
- NZXT H630 Ultra Tower Chassis @ eTeknix
- Fractal Design Arc Midi R2 Case @ Benchmark Reviews
- Cooltek Coolcube Maxi Black @ techPowerUp
- Spire X2 6018 XMOD Chassis @ eTeknix
- Lian Li PC-TU100 Mini-ITX Case @ AnandTech
- Thermaltake Chaser A31 Thunder Case Review @ Ninjalane
Subject: Editorial, General Tech, Cases and Cooling | May 29, 2013 - 02:03 PM | Scott Michaud
Tagged: Windows key, mouse, microsoft, I Hate This Key
Has this ever happened to you while playing a shooter? You need to get to a position so you mash the alt key to sprint and... aw crap I hit the Windows key... well, now I am dead. Have you ever considered purchasing software or a gaming keyboard which allows you disable that button?
Have you ever considered purchasing a mouse which also has that button to give both hands something to fear?
Definitely not a member of their Sidewinder product line.
Okay, so I should be fair: the Microsoft Sculpt Comfort mouse is not designed for gaming and Windows 8-like user experiences revolve heavily around the start button. The mouse button is also more useful than a redundant Windows key; the blue pad also has swipe functionality for extra functions. According to how it is described on its product page, slide gestures are bound to respond to the computer as mouse buttons 4 and 5.
So you can probably bind them to game functions, if you feel daring.
But, in the end, I still need to congratulate Microsoft for trying to innovate computer hardware. This is more than just trying to graft touch functionality to a mouse surface, as both Apple and Microsoft have tried in the past, and tries to make the classical mouse experience better. I doubt it is for most of our audience, but not everything needs to be.
Subject: Cases and Cooling | May 21, 2013 - 11:52 PM | Tim Verry
Tagged: be quiet, Power Supplies, haswell, Intel, c6, c7
In addition to Be Quiet!, Thermaltake has announced its own list of Haswell-compatible PSUs. The majority of high end Thermaltake power supplies will work with Haswell and its new sleep states. Further, all of the current generation high-end and mid-range Thermaltake power supplies are compatible with the new CPUs.
Power supplies in the Toughpower, EVO, and Smart M family are compatible with Haswell. Specifically, the chart below details which specifc models are compatible with Haswell and the new C6 and C7 low power sleep states.
The following companies have also listed Haswell-compatible power supplies:
Subject: Cases and Cooling | May 21, 2013 - 10:50 PM | Tim Verry
Tagged: sleep state, PSU, Power Supplies, haswell, c7, c6, be quiet
Be quiet!, a power supply manufacturer based in Germany, has announced that almost all of its recent power supply lineups are fully compatible with Intel's upcoming Haswell processors. The PC Perspective team has talked in-depth about the new C6 and C7 sleep states used by Haswell CPUs. However, for the uninitiated, the new Intel processors have two new low power sleep states. The lowest state, C7, draws as little as 0.05A from the 12V PSU rail. That is a good thing, but not all power supplies will be compatible with the new sleep states as such low load on the 12V rail was not a concern when the PSUs were designed and manufactured. Notably, even incompatible power supplies will still work in Haswell systems, but those computers will not be able to enter the lower-power C6 and/or C7 sleep states.
There is good news for users of Be Quiet! Power supplies, however. The following power supplies are fully compatible with Haswell and the new sleep states:
- Dark Power Pro 10 Series (all models)
- Straight Power E9 Series (all models)
- Pure Power L8 Series (all models)
- System Power 7 Series (all models)
- Pure Power L7 Series (the 630W and 730W models only)
Older Be Quiet! power supplies will still work in Haswell systems, but use of the lowest power C7 state is not recommended. Fortunately, most desktop users can live without the new low power states (which, while nice to have, the new sleep states are more beneficial to laptop users).
As the launch of Haswell approaches, more and more PSU manufacturers are releasing compatibility information. So far, the following companies have put together compatibility lists.
Subject: General Tech, Cases and Cooling | May 14, 2013 - 03:20 PM | Jeremy Hellstrom
Tagged: Lian Li, PC -Q30, mini ITX, case
Lian Li has just released a very unique case for those who want to show off their internal components, the PC-Q30. The unique curved chassis will certainly make your system stand out as no other competitor is offering a case with this particular look. It is mini-ITX so their are some space constraints for the highest end systems but you can still fit a good system into the (W)223mm x (H)357mm x (D)300mm chassis.
May 14, 2013, Keelung, Taiwan - Lian-Li Industrial Co. Ltd, today announces a new brushed aluminum Mini-ITX chassis – PC-Q30. With its curve-shaped design and large acrylic front window the fully aluminum PC-Q30 allows users to show off their systems, and is sure to be the talking piece of any room.
Whether in the living room, bedroom, or office, the PC-Q30 with its curve-shape and brushed aluminium finish takes visual command without being ostentatious. Additionally, DIY builders can put their stylized internal components and intricate builds on full display – as they should not be hidden from sight.
Thanks to the two expansion slots on the top of the chassis, the PC-Q30 supports graphics cards up to 200mm (7.8”). For storage, up to four 2.5” hard drives or SSDs can be mounted in the removable hard drive cage at the bottom of the chassis.
A 140mm fan in the rear of the chassis expels hot air, while ventilation on the top and side allows for cool air to enter. A small form factor power supply up to 125mm (4.9”) is placed on rubber pads in order to reduce vibrations.
The front of the PC-Q30 is minimalistic in aesthetics and houses the dual LED illuminated power button that glows blue when on and red while loading. The I/O panel with two USB 3.0 ports and HD audio connections is located on the left side of the front of the chassis to not interrupt the elegant aesthetics.
Price and Availability
The PC-Q30 will be available in June in the US and Canada for the suggested retail price of US$149
Subject: General Tech, Cases and Cooling | May 11, 2013 - 09:17 PM | Tim Verry
Tagged: seasonic, haswell, Power Supplies, PSU, 0.05A
Following the announcements from other power supply manufacturers, Seasonic has now released a list of its own power supplies that are compatible with Intel's upcoming Haswell processor. The new Haswell CPUs, set to launch June 3rd, incorporate new C6 and C7 sleep states that draw as little as 0.05A from the 12V PSU rail. Because of the low load, some existing power supplies will have issues with the new sleep states and could result in system instability. In light of that, many manufacturers are validating their existing lineups to determine which ones are compatible.
As of the time of publication, the following power supplies from Seasonic are compatible with Haswell and the new sleep states.
Platinum Fanless Series
M12 II Evo Edition Series
Stay tuned to PC Perspective for more information on PSU and Haswell compatibility.
Subject: Editorial, General Tech, Cases and Cooling, Processors | May 10, 2013 - 04:23 PM | Scott Michaud
Tagged: c6, c7, haswell, PSU, corsair
I cannot do it captain! I don't have the not enough power!
We have been discussing the ultra-low power state of Haswell processors for a little over a week and how it could be detrimental to certain power supplies. Power supply manufacturers never quite expected that you could have as little as a 0.05 Amp (0.6W) draw on the 12V rail without being off. Since then, companies such as Enermax started to list power supplies which have been tested and are compliant with the new power requirements.
|AXi||AX1200i||Yes||100% Compatible with Haswell CPUs|
|AX860i||Yes||100% Compatible with Haswell CPUs|
|AX760i||Yes||100% Compatible with Haswell CPUs|
|AX||AX1200||Yes||100% Compatible with Haswell CPUs|
|AX860||Yes||100% Compatible with Haswell CPUs|
|AX850||Yes||100% Compatible with Haswell CPUs|
|AX760||Yes||100% Compatible with Haswell CPUs|
|AX750||Yes||100% Compatible with Haswell CPUs|
|AX650||Yes||100% Compatible with Haswell CPUs|
|HX||HX1050||Yes||100% Compatible with Haswell CPUs|
|HX850||Yes||100% Compatible with Haswell CPUs|
|HX750||Yes||100% Compatible with Haswell CPUs|
|HX650||Yes||100% Compatible with Haswell CPUs|
|TX-M||TX850M||Yes||100% Compatible with Haswell CPUs|
|TX750M||Yes||100% Compatible with Haswell CPUs|
|TX650M||Yes||100% Compatible with Haswell CPUs|
|TX||TX850||Yes||100% Compatible with Haswell CPUs|
|TX750||Yes||100% Compatible with Haswell CPUs|
|TX650||Yes||100% Compatible with Haswell CPUs|
|GS||GS800||Yes||100% Compatible with Haswell CPUs|
|GS700||Yes||100% Compatible with Haswell CPUs|
|GS600||Yes||100% Compatible with Haswell CPUs|
|CX-M||CX750M||Yes||100% Compatible with Haswell CPUs|
|CX600M||TBD||Likely compatible — currently validating|
|CX500M||TBD||Likely compatible — currently validating|
|CX430M||TBD||Likely compatible — currently validating|
|CX||CX750||Yes||100% Compatible with Haswell CPUs|
|CX600||TBD||Likely compatible — currently validating|
|CX500||TBD||Likely compatible — currently validating|
|CX430||TBD||Likely compatible — currently validating|
|VS||VS650||TBD||Likely compatible — currently validating|
|VS550||TBD||Likely compatible — currently validating|
|VS450||TBD||Likely compatible — currently validating|
|VS350||TBD||Likely compatible — currently validating|
Above is Corsair's slightly incomplete chart as of the time it was copied from their website, 3:30pm on May 10th, 2013; so far it is coming up all good. Their blog should be updated as new products get validated for the new C6 and C7 CPU sleep states.
The best part of this story is just how odd it is given the race to arc-welding (it's not a podcast so you can't Bingo! hahaha!) supplies we have been experiencing over the last several years. Simply put, some companies never thought that component manufacturers such as Intel would race to the bottom of power draws.
Subject: Cases and Cooling | May 8, 2013 - 03:43 PM | Tim Verry
Tagged: cooler master, n200, n400, n600, atx case
PC case and cooling manufacturer Cooler Master has launched a slew of new cases, including the N200, N400, and N600 cases. The new N series spans from Micro ATX to full tower cases. All three cases are black with mesh fan grills with front IO that supports two USB 3.0, two USB 2.0, and two audio ports.
The N200 is the smallest of the three cases. It is constructed of steel (with a plastic front bezel) and measures 202 x 378 x 445mm. The N200 case can host mini-ITX or micro-ATX motherboards, up to two optical drives, four SSDs, and three hard drives. The case comes with two Cooler Master XtraFlow fans, but it can also fit a thin 240mm radiator in the front of the case if you remove the SSD drive bays. A 120mm rear fan rounds out the cooling options. It supports CPU HSFs up to 160mm tall.
The N400 is a bit larger at 190 x 426 x 501.4mm. The mid-tower case can support full ATX motherboards, 320mm long GPUs, and up to eight 120mm fans. A maximum of eight hard drives and seven expansion cards are also supported. Cooler Master provides two XtraFlow fans with the case.
Cooler Master’s N600 rounds out the new case series. The case measures 207 x 455 x 520mm and is constructed of a plastic polymer. In addition to the included XtraFlow fans, the case can accommodate up to 8 more 120mm fans. It has a removable hard drive cage that allows gamers to use graphics cards up to 430mm GPUs. A 240mm water cooling radiator can be installed in the top of the case as well. The N600 has a large mesh front panel that allows for front intake fans.
According to TechPowerUp, the Cooler Master N200 will be available in Europe later this month for 33 Euros while the larger N400 and N600 cases will be available in June for 42 Euros and 67.5 Euros respectively. Those prices work out to about $43 for the N200, $55 for the N400, and $89 for the N600, though that could change a bit as there is no word on official US pricing yet. Personally, I'm not a fan of the aesthetics, but at least the prices aren't terrible.
Subject: Cases and Cooling | May 8, 2013 - 01:46 PM | Tim Verry
Tagged: ultra tower, nzxt, h630, grid hub, case
NZXT has unleashed a monstrous new PC case onto the tech world with the H630 Ultra Tower. The new chassis is constructed of powder coated steel and ABS plastic. It can accommodate XL-ATX motherboards, two 360mm radiators, 8 hard drives, and a bunch of fans within its sound dampened interior. The H630 case weighs approximately 31 pounds and measures 547 x 245 x 567mm (HxWxD).
On the outside, the NZXT features a glossy white or black powder coated finish. You will not find any case windows or bling, but the design is clean and simple. It offers filtered fan intakes and an IO panel located on the right side with two USB 2.0, two USB 3.0, and two audio ports as well as a SDXC card slot. Two 5.25” drive bays adorn the top-front of the case.
The inside of the case is rather spacious with an optical drive bay, three removable hard drive bays, an opening for a bottom mounted PSU, and a large motherboard tray that can hold boards up to XL-ATX in size. Water cooling enthusiasts will be pleased to know that they can mount a 360mm radiator in the top and front of the case, which is a pretty impressive feat without needing to use an externally-mounted rad (like I had to with my case). If you opt for additional air cooling, you can further fit two 140mm fans in the bottom of the case, one 140mm case in the HDD cage, and one 140mm case in the rear of the case. Needless to say, that’s a lot of cooling options!
NZXT has also outfitted the H630 with sound dampening material, which should help to soften the noise of all the hardware enthusiasts are likely to pack into the case--though I would wait for reviews to see how well the material works. Additionally, the H630 has 9 expansion slots, cable routing holes, the company's 10-port Grid fan hub, and two 2.5” SSD mounts hidden behind the motherboard tray.
The new H630 Ultra Tower should be available in the US for around $150 by the end of May and in the UK for £129.05 sometime in June. For the price, it seems like an impressive deal. I’m tempted, though I’m not sure if it will fit under my desk. You can find more photos and specifications on this NZXT product page.
Subject: Cases and Cooling | May 6, 2013 - 06:49 PM | Jeremy Hellstrom
Tagged: evercool, Venti HPQ-12025
If you need an inexpensive and relatively small heatsink then FrostyTech has a review you should check out. At a mere 125x68x160mm and 588g the Evercool Venti HPQ-12025 is tiny compared to many on the market and at $30 it is significantly less expensive than larger competitors. With that small footprint you could be forgiven for thinking that performance would suffer but FrostyTech's testing shows it to be a solid midrange performer and still reasonably efficient when running the fan at its lowest speed.
"Airflow is driven by a single 120mm PWM fan whose snow white 7-bladed impeller rotates at your basic 2200RPM to 800RPM. Noise output is moderate. Because computer enthusiasts tend to be picky bunch, Evercool have tossed in one extra set of wire fan clips."
Here are some more Cases & Cooling reviews from around the web:
- Silverstone Heligon Series HE01 CPU Cooler Review @ Pro-Clockers
- Scythe Ashura / Katana 4 CPU cooler @ Hardware.info
- SilverStone Argon Series AR01 CPU Cooler @ eTeknix
- Noctua NH-U12S CPU Cooler @ Tweaktown
- Cooler Master TPC-612 review: cheaper TPC-800 CPU cooler @ Hardware.info
- Noctua NH-U12S & NH-U14S CPU Coolers Review @ NikKTech
- Evercool Silent Shark CPU Cooler @ X-bit Labs
- Noctua NH-U14S CPU Cooler @ eTeknix
- Alpenfohn Fohn 120 and 140 WingBoost Fan @ eTeknix
- Noctua NF-S12A 120mm Fans Review @ Hi Tech Legion
- Cougar 120mm Dual-X Fan Review @ Hi Tech Legion
- Noctua NF-A14 FLX and ULN 140mm Case Fan Review @ Ninjalane
- Spire X2 120mm PWM Fan Review @ Hi Tech Legion
- NZXT Kraken X40 Compact Liquid Cooling System Review: New Level of Cool @ X-bit Labs
- Enermax Hoplite ST Gaming Tower Review @ Pro-Clockers
- Silverstone Redline RL04 Mid-Tower Computer Case Review @ Hi Tech Legion
- InWin G7 Mid-Tower Chassis @ Tweaktown
- Thermaltake Chaser A41 Mid-Tower @ FunkyKit
- Lian Li PC-V750WX Compact E-ATX Case @ Benchmark Reviews
- Fractal Design ARC Midi R2 Mid-Tower @ Tweaktown
- NZXT Phantom 630 Full Tower Case Review @ Hi Tech Legion
- Aerocool Xpredator case @ Rbmods
- Corsair Obsidian 350D Case Review @ Hardware Secrets
- Corsair 350D M-ATX Chassis @ eTeknix
- LanCool First Knight PC-K65B Mid Tower Case Review @ Hi Tech Legion
- A quick look at BitFenix's Prodigy enclosure @ The Tech Report
- Lian Li PC-V650B @ techPowerUp
- Antec GX700 Military Case @ Rbmods
- Antec GX700 Mid Tower Chassis @ eTeknix
Austrian PC Cooling manufacturer Noctua has released a new fan called the NF-A14. The new fan is PWM controlled and aimed at case or watercooling radiator cooling. The NF-A14 uses a square frame and features higher static pressure than the NF-P13 along with a maximum speed of 1500RPM.
The fan kit comes with the fan itself, mounting screws, a rubber mounting system to reduce vibration, a 30mm extension cable, low-noise adapter, and a 4-pin Y splitter cable that allows two PWM fans to be connected to a single motherboard fan header. The new Noctua NF-A14 comes with a 6 year warranty.
You can find more information on Noctua’s website as well as the full press release after the break.
In other cooling news:
- Passively Cooled GTX 570 SLI Setup @ Bit-Tech.net
- Impactics D1NU1 Passive NUC Case HSF @ FanlessTech
- Noctua NH-L12 CPU HSF Review @ ChipLoco
Subject: Cases and Cooling, Processors | May 1, 2013 - 03:07 PM | Ryan Shrout
Tagged: power supply, Intel, idle, haswell, c7, c6
I came across an interesting news story posted by The Tech Report this morning that dives into the possibility of problems with Intel's upcoming Haswell processors and currently available power supplies. Apparently, the new C6 and C7 idle power states that give the new Haswell architecture benefits for low power scenarios place a requirement of receiving a 0.05 amps load on the 12V2 rail. (That's just 50 milliamps!) Without that capability, the system can exhibit unstable behavior and a quick look at the power supply selector on Intel's own website is only listing a couple dozen that support the feature.
This table from VR-Zone, the source of the information initially, shows the difference between the requirements for 3rd (Ivy Bridge) and 4th generation (Haswell) processors. The shift is an order of magnitude and is quite a dramatic change for PSU vendors. Users of Corsair power supplies will be glad to know that among those listed with support on the Intel website linked above were mostly Corsair units!
A potential side effect of this problem might be that motherboard vendors simply disable those sleep states by default. I don't imagine that will be a problem for PC builders anyway since most desktop users aren't really worried about the extremely small differences in power consumption they offer. For mobile users and upcoming Haswell notebook designs the increase in battery life is crucial though and Intel has surely been monitoring those power supplies closely.
I asked our in-house power supply guru, Lee Garbutt, who is responsible for all of the awesome power supply reviews on pcper.com, what he thought about this issue. He thinks the reason more power supplies don't support it already is for power efficiency concerns:
Most all PSUs have traditionally required "some load" on the various outputs to attain good voltage regulation and/or not shut down. Not very many PSUs are designed yet to operate with no load, especially on the critical +12V output. One of the reasons for this is efficiency. Its harder to design a PSU to operate correctly with a very low load AND to deliver high efficiency. It would be easy just to add some bleed resistance across the DC outputs to always have a minimal load to keep voltage regulation under control but then that lowers efficiency.
Subject: Cases and Cooling | April 26, 2013 - 12:30 AM | Tim Verry
Tagged: noctua, nh-l9a, hsf, cooler, mini-itx, low profile cooler
Noctua, an Austrian company known for its high-end air CPU coolers has announced that it will be offering up alternatvie mounting kits to users of its low profile NH-L9a cooler that have incompatible motherboards. Certain mini-ITX motherboards that place components on the back of the motherboard around the processor socket are incompatible with the company’s existing SecureFirm 2 mounting kit because the backplate cannot be installed.
The new alternative mounting system for the NH-L9a CPU cooler uses Noctua’s NM-APS3 spacers that go in place of the standard backplate. The spacers go in between the motherboard and screws, but are small enough to not run into any components installed in the area normally reserved for a CPU backplate. Two such boards that Noctua has found to be incompatible are the mini-ITX AsRock FM2A75M-ITX and AsRock FM2A85X-ITX.
Users with an incompatible motherboard and NH-L9a cooler can obtain the alternative mounting kit for free by contacting Noctua’s customer service line and providing them with a proof of purchase (scan, photo, or electronic invoice) receipt for both the Noctua cooler and an incompatible motherboard. Additionally, Noctua will be including both the standard SecureFirm 2 and alternative mounting kits in the retail NH-L9a cooler box from now on.
It is nice to see Noctua continuing its tradition of good customer care. They many not be as popular as other cooler vendors in the US but it seems they are a company willing to go the extra mile for its enthusiast customers.