Enermax updates its AIO coolers with the Liqmax II 120s

Subject: Cases and Cooling | November 23, 2015 - 01:42 PM |
Tagged: AIO, enermax, liquimax II 120s, watercooling

Enermax's Liqmax II 120s is a relatively small AIO watercooler, the radiator is 154x120x27 mm (6.1x0.8x1.0") and will fit on any modern motherboard, Intel or AMD.  The two 120mm fans which come with the cooler are high static pressure fans with the moniker Batwing and have a physical screw on them which allows you to tune the fan speed manually.  Modders Inc were impressed with this cooler, it performed relatively well and quite quietly and the fact thatit sells for $75 doesn't hurt either. 


"When it comes to a new build I always keep cooling in mind. Not every rig I build has custom water reservoirs, custom piping or fancy radiators. Sometimes I just need a machine to work without spending an enormous amount of cash on custom parts. I find that All in One (AIO) cooling systems are easy to install, work well …"

Here is some more Tech News from around the web:

Tech Talk


Source: Modders Inc

On-die watercooling

Subject: General Tech | October 7, 2015 - 01:06 PM |
Tagged: watercooling, nifty

These researchers are skipping the waterblock altogether and have made channels in surface of the die its self for de-ionized water to flow through and cool the chip.  The 28-nanometer Altera FPGA they tested this cooling method on had numerous channels cut into it which were then sealed up with a layer of silicon.  With a flow rate of 147 ml/minute they kept the chip to a comfortable 24C, a mere 4C higher than the temperature of the water and significantly lower than the 60C the chip would run at using air cooling.  Neither Hack a Day nor PCPer encourage you to try to cut micron sized channels in your brand new processor, however we all hope to see this cooling technique incorporated into heatspreaders in future generations of processors.


"Researchers at Georgia Tech have been working on cutting fluid channels directly into the back of commercial silicon die (an Altera FPGA, to be exact). The tiny channels measure about 100 micron and are resealed with another layer of silicon. Water is pumped into the channels to cool the device efficiently."

Here is some more Tech News from around the web:

Tech Talk

Source: Hack a Day

Watercooling your EVGA X99 with Bitspower

Subject: Cases and Cooling | March 24, 2015 - 02:12 PM |
Tagged: evga, X99 Classified, X99 FTW, watercooling, Bitspower, THOR EIX99

Now that most of the features once present on motherboards have been moved to the CPU there is far less need to watercool your chipset.  However for the extreme overclocker there are advantages to cooling the MOSFETs on the VRM and PCH as well as the CPU itself.  Modders-Inc has just reviewed the Bitspower THOR EIX99, specifically designed for EVGA's X99 Classified and FTW motherboards. The acrylic housing for the waterblocks bring a unique look to your motherboard as well as offering improvements to heat management.  By installing the cooler Modders-Inc hit 4.5 GHz on an i7 5960X, not too bad for a $160 investment.  The installation was simple but if you invest the time to design a custom watercooling loop you can get even more performance out of this kit.


"Bitspower makes various options for water blocks that cover Gigabyte, ASRock, MSI, Asus and EVGA motherboards. Recently, we reviewed the EVGA X99 Classified and that motherboard is designed to push the CPU as high as possible if the cooling equipment allows. Bitspower’s THOR EIX99 is specifically designed to cover the EVGA X99 Classified as well as the EVGA X99 FTW motherboard, cooling the critical motherboard components and providing the thermal headroom that the MOSFETs and other parts require for a stable overclock."

Here are some more Cases & Cooling reviews from around the web:


Source: Modders Inc

360mm of radiator; the Thermaltake Water 3.0 Ultimate

Subject: Cases and Cooling | March 16, 2015 - 03:39 PM |
Tagged: thermaltake, Water 3.0 Ultimate, watercooling, AIO

Using the Asetek Gen 4 pump and a radiator measuring 393mm x 120mm x 27mm the Thermaltake Water 3.0 Ultimate is a large cooler designed for serious overclockers.  The fans are rated at 99CFM and are set up properly with PWM connections to balance noise and performance.  Overclockers Club increased their i7-4770K to 4.2GHz and this cooler kept the CPU at an impressive 67 °C, topping the charts of the coolers they have tested previously.  They managed to get the chip running at 4.5GHz on 1.241 volts which raised the temperature to 75 °C but that was the highest frequency that particular i7-4770K could reach.  Check out their full review here.


"Cooling capacity is dependent on air flow and the Ultimate has you covered. You have close to 300CFM of air at your command, so expect to notice the fans when you crank up the heat and with a cooler this size, a little fan noise just goes with the territory. Thermaltake has refined a few components to make the installation about as easy as it can be. The low profile Asetek pump looks good and is quiet. Even at a 4.5GHz overclock, the Ultimate still has some thermal room if your chip can handle a higher overclock."

Here are some more Cases & Cooling reviews from around the web:


Podcast #273 - Corsair 750D, a XSPC Watercooling Kit, the Steam Controller and more!

Subject: General Tech | October 17, 2013 - 06:35 PM |
Tagged: podcast, video, corsair, halloween, costume, contest, XSPC, watercooling, radiator, steam, SteamOS, Steam Controller

PC Perspective Podcast #273 - 10/17/2013

Join us this week as we discuss the Corsair 750D, a XSPC Watercooling Kit, the Steam Controller and more!

You can subscribe to us through iTunes and you can still access it directly through the RSS page HERE.

The URL for the podcast is: http://pcper.com/podcast - Share with your friends!

  • iTunes - Subscribe to the podcast directly through the iTunes Store
  • RSS - Subscribe through your regular RSS reader
  • MP3 - Direct download link to the MP3 file

Hosts: Ryan Shrout, Jeremy Hellstrom, Josh Walrath, and Allyn Malventano

Program length: 1:10:56
  1. PC Perspective Halloween Hardware Giveaway - Brought to you by Corsair and Gigabyte

  2. Week in Review:
  3. This episode is brought to you by Carbonite.com! Use offer code PC for two free months!
      1. Skylake (2015) reportedly not affected
  4. Hardware/Software Picks of the Week:
  5. podcast@pcper.com
  6. Closing/outro


EVGA Outfits GTX 780 With Hydro Copper Water Block

Subject: Graphics Cards | June 1, 2013 - 01:38 PM |
Tagged: watercooling, nvidia, hydro copper, gtx 780, gpu, gk110, evga

EVGA GTX 780 Hydro Copper GPUs

While NVIDIA restricted partners from going with aftermarket coolers on the company's GTX TITAN graphics card, the recently released NVIDIA GTX 780 does not appear to have the same limits placed upon it. As such, many manufacturers will be releasing GTX 780 graphics cards with custom coolers. One such design that caught my attention was the Hydro Copper full cover waterblock from EVGA.

EVGA GTX 780 with Hydro Copper Water Block (2).jpg

This new cooler will be used on at least two upcoming EVGA graphics cards, the GTX 780 and GTX 780 Classified. EVGA has not yet announced clockspeeds or pricing for the Classified edition, but the GTX 780 Hydro Copper will be a GTX 780 GPU clocked at 980 MHz base and 1033 MHz boost. The 3GB of GDDR5 memory is stock clocked at 6008 MHz, however. It uses a single 8-pin and a single 6-pin PCI-E power connector. This card is selling for around $799 at retailers such as Newegg.

The GTX 780 Classified Hydro Copper will have a factory overclocked GTX 780 GPU and 3GB of GDDR5 memory at 6008 MHz, but beyond that details are scarce. The 8+8-pin PCI-E power connectors do suggest a healthy overclock (or at least that users will be able to push the cards after they get them).

Both the GTX 780 and GTX 780 Classified Hydro Copper graphics cards feature two DL-DVI, one HDMI, and one DisplayPort video outputs.

EVGA GTX 780 Classified with Hydro Copper Water Block (1).jpg

The Hydro Copper cooler itself is the really interesting bit about these cards though. It is a single slot, full cover waterblock that will cool the entire graphics card (GPU, VRM, Memory, ect). It has two inlet/outlet ports that can be swapped around to accommodate SLI setups or other custom water tube routing. A configurable LED-backlit EVGA logo adorns the side of the card and can be controlled in software. A 0.25 x 0.35 pin matrix is used in the portion of the block above the GPU to increase the surface area and aid in cooling. Unfortunately, while the card and cooler are single slot, you will actually need two case PCI expansion slots due to the two DL-DVI connectors.

It looks like a neat card, and it should perform well. I'm looking forward to seeing reviews of the card and how the cooler holds up to overclocking. Buying an overclocked card with a pre-installed waterblock is not for everyone but having a water cooled GPU with a warranty will be worth it more than pairing a stock card with a custom block.

Source: EVGA

Is bigger better for Corsair's self-contained watercoolers

Subject: Cases and Cooling | March 4, 2013 - 01:50 PM |
Tagged: watercooling, corsair, H90, H110, 140mm

The Corsair H90 and H110 use larger 140mm fans with 140mm and and 280mm radiators respectively.  [H]ard|OCP compared them to also relatively recent H100i and H80i, 120mm based coolers that are controllable with Corsair's LINK technology.  The comparison was rather favourable for the new 140mm coolers, with both new models beating the H100i at stocks speeds and beating their respective cousins on an overclocked chip; perhaps more importantly these two models did so with noticeably reduced sound levels.  If you need serious cooling and aren't crazy about noise, these two coolers should be on your list.


"Corsair, once known only for quality enthusiast RAM modules, has successfully diversified its products reaching into cases, power supplies, processor cooling solutions. With the release of the H90 and H110 Hydro Series, we see the first new refresh in its closed loop liquid cooling systems."

Here are some more Cases & Cooling reviews from around the web:


Source: [H]ard|OCP

Corsair updates their self contained watercoolers and not just with an 'i' at the end

Subject: Cases and Cooling | February 13, 2013 - 07:20 PM |
Tagged: corsair, Hydro Series, H80i, H100i, watercooling, Corsair Link

The updated Hydro Series coolers, the H80i and H100i both feature all new tubing that might not be much more flexible than the previous models but offers improved flow rates.  As well these coolers are now able to be controlled via Corsair's Link technology, allowing you to either set the LED colour displayed or to use it as a real time temperature indicator.  As you would suspect the H100i is the larger of the two units, the H80i being 120 x 38 x 152mm and the H100i measuring 275 x 120mm x  27mm with both supporting up to four fans via the Link software.  [H]ard|OCP saw an improvement from the previous models which you can read about in their full review.


"Corsair updates its aging H80 and H100 performance liquid CPU coolers, with the new H80i and H100i models. Changes include a new cold plate design, smooth outer diameter no-kink tubing designed to further limit evaporation, and newer designed fans claiming better static pressures, and quieter operation."

Here are some more Cases & Cooling reviews from around the web:


Source: [H]ard|OCP

NZXT Unleashes the Kraken -- World's first all-in-one 140mm & 280mm liquid-cooler

Subject: Cases and Cooling | October 31, 2012 - 05:18 PM |
Tagged: watercooling, all-in-one, nzxt, Kraken X40, Kraken X60

30th October, 2012 – High performance liquid cooling has finally arrived in an easy to use, all-in-one package. NZXT releases the Kraken, the first premium all-in-one water cooler series for PC enthusiasts and gamers alike. The Kraken X40 and Kraken X60 are high end, all-in-one 140mm and 280mm liquid-cooling solutions where ease of use meets unmatched performance.

Applying its forward-thinking design philosophy to the water-cooling market, NZXT raises the bar with a userfriendly solution that brings unrivaled liquid-cooling performance to your fingertips. With 36% more surface area than standard 120mm/240mm radiators and fully interactive fan control, NZXT’s Kraken series is nothing short of a water-cooling behemoth.

NZXT brings its innovative HUE controlled lighting system to the Kraken, setting a new standard for design and performance. Featuring premium black sleeved cables and extended 16-inch tubing for large tower support, the Kraken brings high performance cooling with an uncompromised look that any enthusiast will be dying to show off.

Kraken 40.jpg

At its core, the Kraken features a state-of-the-art pump attached to an all copper base that is compatible with all of the current offerings from Intel and AMD. Included with the 140mm Kraken X40 is one NZXT FX-140 PWM fan, with the ability to install an additional 140mm fan for a push-pull configuration, offering unmatched cooling performance.

Kraken 60.jpg

The 280mm Kraken X60 features two NZXT FX-140 PWM fans, with the ability to install an additional two fans for a push-pull configuration as well. Additionally, the Kraken X60 utilizes a SATA power connector for easy installation and effortless cable management.

Both Krakens are aggressively priced at $99 and $139 for the X40 and X60, respectively, and backed by a 2 year warranty. With the Kraken, NZXT set out to unleash the best closed loop water cooler on the market, and believes its customers should not settle for anything less.

Source: NXZT

Corsair Announces Updated Hydro Series H60 and New Hydro Series H55

Subject: Cases and Cooling | October 25, 2012 - 02:15 PM |
Tagged: corsair, watercooling, hydro H60, hydro H55, hydro

FREMONT, California — October 25, 2012 — Corsair, a worldwide designer and supplier of high-performance components to the PC gaming hardware market, today announced an updated version of the award-winning Hydro Series H60 liquid CPU cooler, and the new Hydro Series H55 liquid CPU cooler.

The Hydro Series H55 is an update to the hugely respected Hydro Series H50, and is based on the latest, 4th generation cold-plate design. The updated version of the Hydro Series H60 takes advantage of the latest cold plate, manifold and fan technology to further increase performance and reduce noise levels.

"The Hydro Series H50 and H60 have a hard-won reputation for delivering effective, reliable, and quiet CPU cooling,” said Thi La, Senior VP & GM of Memory and Enthusiast Component Products at Corsair. "These new and improved versions demonstrate Corsair’s commitment to providing our customers with the latest and best integrated liquid cooling technology.”

In addition to the new cold plate and manifold design, the Hydro Series H60 also utilizes larger diameter tubing, which increases the coolant flow rate and performance. The new composite rubber tubing makes installation easier, but retains the low-evaporation rates of the older, more rigid tubing, guaranteeing a long lifetime. The Hydro Series H60 also introduces a new magnetic mounting bracket, which makes it simple to select the correct motherboard socket format.


H60 Includes Fan Based on Award Winning Air Series SP120

A high-quality fan designed specifically to move air through the fins of a liquid cooling radiator is an essential part of any liquid cooling system. The new H60 includes a 120mm fan based on the award-winning Air Series SP120. This utilizes a motor that has been specially tuned for high torque, ensuring outstanding static pressure, and consistently high performance at low noise levels.


The Hydro Series H55 is designed to provide a simple and effective upgrade from a basic CPU air cooler. The 4th generation cold plate design, and high static-pressure, low noise 120mm fan provides great performance, while the tool-free mounting bracket and low-permeability rubber tubing makes installation simple.

Both the Hydro Series H55 and Hydro Series H60 CPU coolers are compatible with most cases that feature a rear 120mm fan mount. Both support motherboards based on the Intel LGA115x/1366/2011, and AMD AM2/AM3/FM1 sockets, and are backed by a five year limited warranty.

Pricing and Availability

The Corsair Hydro Series H60 is available immediately from Corsair’s worldwide network of resellers and distributors, at a price of $79.99 in the United States.

The Corsair Hydro Series H55 is available immediately from Corsair’s worldwide network of resellers and distributors, at a price of $69.99 in the United States.

Source: Corsair