Subject: Motherboards | June 4, 2013 - 03:12 AM | Tim Verry
Tagged: ROG, mini-itx, mini ITX, maximus vi impact, maximus vi, computex 2013, computex, asus
ASUS held a Republic of Gamers press conference earlier today that focused on new product announcements for its ROG brand. Among the new ROG gear was the company's first Mini-ITX ROG motherboard with the ASUS Maximus VI Impact motherboard.
This board may be tiny, but it is packed with features and overclocking-friendly hardware! This Mini-ITX motherboard is clad in the red and black ROG color scheme and features ASUS' Impact Power add on card that takes the VRMs and other electrical regulation hardware up off of the mainboard and into a separate add in card above the CPU. This Impact Power riser card includes a 8+2 digital power phase for both the CPU and memory. The board also includes a SupremeFX Impact sound card and a mPCIe Combo II card. The SupremeFX Impact module uses ELNA audio capacitors and features a headphone amplifier and 115dB SNR (Signal-to-Noise Ratio). Further, the mPCIe Combo II card provides a NGFF (think of this as next-generation mSATA) slot as well as 802.11ac Wi-Fi and Bluetooth 4.0 wireless radios.
Apart from the bundled ASUS cards, the board provides a single PCI-E 3.0 x16 slot, two DDR3 memory slots, four SATA 3 ports, and (of course) the LGA 1150 CPU socket ready to accept an Intel Haswell processor. The board comes with a standard 24-pin ATX and 8-pin CPU power connectors.
The rear IO panel includes:
- 2 x HDMI
- 1 x S/PDIF
- Impact Control and BIOS reset buttons
- 4 x USB 2.0
- 1 x eSATA
- 4 x USB 3.0
- 1 x RJ45 Gigabit Ethernet
- 3 x Audio jacks (via SupremeFX sound card)
ASUS has not yet announced pricing or availability for this Mini-ITX Maximus VI Impact motherboard, but it looks like a solid board and I am anxious to see how well it overclocks!
Also read: ASUS Z87 Motherboard Lineup Preview @ PC Perspective.
Subject: Systems | May 31, 2013 - 07:01 PM | Jeremy Hellstrom
Tagged: htpc, mini-itx
Building a mini-ITX system that is small enough to be attached to the back of a monitor or hidden with your stereo components takes a bit more thought than assembling a full ATX system. It is not just about the size of the components you are purchasing, heat dissipation is much more important in a small system especially if it will be located somewhere that does not have great air circulation. TechSpot has put together a guide for those thinking of building such a system, using the Akasa Euler Case as the housing and powered with a Core i5-3470T. As you can see from the picture below, the final system is smaller than an HD7970.
"The idea behind the Thin Mini-ITX form factor, besides the obvious which is to create seriously compact computers, is also to allow for DIY all-in-ones (think of little PCs you can attach to the back of your monitor). Having that said, we don't fully intend to go the all-in-one route in this article, but are aiming to build a powerful Thin Mini-ITX system that can be used in the office or at home as a media PC.
This is what our finished system should look like: extremely compact, powerful, and near silent operation, as in no-moving-parts silent. For less than $700 including a 256GB SSD, we believe you'll love what the final product will look like."
Here are some more Systems articles from around the web:
- Sapphire Edge HD4 @ Bjorn3D
- Streacom F7C EVO HTPC Chassis @ eTeknix
- Fractal Design Node 605 Silent HTPC Case Review @ Legit Reviews
- Leawo Total Media Converter Ultimate @ Benchmark Reviews
- Samsung BD-F7500 Review @ TechReviewSource
- Analogix Semiconductor SlimPort Cable (HDMI Adapter) @ Tweaktown
Subject: General Tech | May 22, 2013 - 06:27 PM | Tim Verry
Tagged: fractal design, mini-itx, case, Node 304
Fractal Design is launching a new version of its existing Node 304 computer chassis. The new Node 304 White comes in white and supports Mini-ITX motherboards. The case measures 250 x 210 x 374mm and weighs 4.9kg.
The Node 304 is constructed of aluminum and has a white painted exterior. There are two mesh air vents on either side of the case as well as two 92mm Silent Series R2 fans working as front intakes behind filters to keep dust out of the case. Front IO includes two USB 3.0 ports and two audio jacks. The rear of the case features two expansion slots, a space for an ATX power supply, and a single 140mm Silent Series R2 exhaust fan.
Internally, the Node 304 White can fit standard ATX power supplies, a Mini-ITX motherboard, and up to six 3.5" or 2.5" hard drives. Alternatively, with two of the hard drive mounts removed, the case can accommodate graphics cards up to 310mm in length.
It is a minimalist design,but one that works well. Airflow should not be a problem even for high-end components, and the inclusion of the three fans, filters, and a fan controller is nice to see. The case will be available in July with an MSRP of $89.90 in the US and 69.90 EURO in Europe.
Subject: Cases and Cooling | April 26, 2013 - 12:30 AM | Tim Verry
Tagged: noctua, nh-l9a, hsf, cooler, mini-itx, low profile cooler
Noctua, an Austrian company known for its high-end air CPU coolers has announced that it will be offering up alternatvie mounting kits to users of its low profile NH-L9a cooler that have incompatible motherboards. Certain mini-ITX motherboards that place components on the back of the motherboard around the processor socket are incompatible with the company’s existing SecureFirm 2 mounting kit because the backplate cannot be installed.
The new alternative mounting system for the NH-L9a CPU cooler uses Noctua’s NM-APS3 spacers that go in place of the standard backplate. The spacers go in between the motherboard and screws, but are small enough to not run into any components installed in the area normally reserved for a CPU backplate. Two such boards that Noctua has found to be incompatible are the mini-ITX AsRock FM2A75M-ITX and AsRock FM2A85X-ITX.
Users with an incompatible motherboard and NH-L9a cooler can obtain the alternative mounting kit for free by contacting Noctua’s customer service line and providing them with a proof of purchase (scan, photo, or electronic invoice) receipt for both the Noctua cooler and an incompatible motherboard. Additionally, Noctua will be including both the standard SecureFirm 2 and alternative mounting kits in the retail NH-L9a cooler box from now on.
It is nice to see Noctua continuing its tradition of good customer care. They many not be as popular as other cooler vendors in the US but it seems they are a company willing to go the extra mile for its enthusiast customers.
Introduction and Technical Specifications
Courtesy of GIGABYTE
The Z77N-WiFi is GIGABYTE's latest edition to the Mini-ITX lineup. Although the board is not as packed with features as some of the other enthusiast-minded mini-ITX boards, GIGABYTE did some interesting things with the board layout to space components out on the board more evenly. The Z77N-WiFi even comes standard with dual-Realtek GbE NICs and an Intel 802.11n-based WiFi mPCIe card. We put the board through our normal gamut of tests to see how well this mighty mite sized up with its full-sized brethren. The Z77N-WiFi board comes with an equally reasonable retail price at a mere $129.99.
Subject: Cases and Cooling | April 19, 2013 - 07:03 AM | Tim Verry
Tagged: PC-Q28, PC-Q27, mini-itx, Lian Li, aluminum case
PC Chassis manufacturer Lian-Li has launched two new mini-ITX cases that will be available next month. The PC-Q27 and PC-Q28 are both brushed aluminum cases that accommodate a single graphics card, a mini-ITX motherboard, at least one case fan, and several hard drives.
The PC-Q27 is the smallest of the two cases at 7.8” x 11.8” x 9.4.” The case is constructed of aluminum and the outside features a black or silver brushed aluminum finish. The front of the case features a single 5.25” optical drive bay, a LED-lit power button, and two USB 3.0 ports on the right side of the case. Internally, the PC-Q27 case uses Lian-Li’s rail motherboard mounting system for mini-ITX boards. It can host a single graphics card up to 195mm in length, two 3.5” hard drives, and one 5.25” drive. The case is cooled by a single 120mm bottom-mounted fan when the hard disk drive bay is removed. To facilitate airflow, the case has vents along the bottom and rear of the case. The case is held up by case feet to allow the fan to pull in cool air.
Meanwhile, the PC-Q28 is a bit larger and wider at 8.9” x 12” x 13.5.” IT also comes in a silver or black brushed aluminum design. This case is the successor to Lian-Li’s PC-Q18. It can hold a mini-ITX motherboard, a single GPU up to 290mm in length, and up to seven 3.5” hard drives. The mini-ITX case features two removable hard drive cages and two fans. There is a single 140mm fan located on the bottom of the case that acts as an intake (and includes a dust filter to keep the case internals clean), and one 120mm exhaust fan on the top of the case. The outside of the case features four case feet to lift the case off the ground, rounded corners, and a simple front panel that host a power button and 5.25” drive bay. The right side of the case hosts two USB 3.0 ports and two analog HD audio jacks.
Both of Lian-Li’s new mini-ITX cases will be available sometime in May. The smaller PC-Q27 has an MSRP of $78.99 while the PC-Q28 will cost $118.99.
Read more about the Mini-ITX form factor at PC Perspective!
Subject: Graphics Cards | April 3, 2013 - 10:14 AM | Tim Verry
Tagged: nvidia, mini-itx, gtx 670, GK104, directcu mini, asus
ASUS has finalized the design for its Kepler-based DirectCU Mini graphics card. The new card combines NVIDIA's GTX 670 GPU and reference PCB with ASUS' own power management technology and a new, much smaller, air cooler. The new ASUS cooler has allowed the company to offer a card that is a mere 17cm long. Compared to traditional GTX 670 graphics cards with coolers at approximately 24cm, the DirectCU Mini is noticeably smaller.
The DirectCU Mini features a GTX 670 GPU clocked at 928MHz base and 1,006MHz boost. It also has 2GB of GDDR5 memory on a 256-bit bus. The card requires a single 8-pin PCI-E power connector. Video outputs include two DVI, one DisplayPort, and a single HDMI port. The ASUS cooler includes a copper vapor chamber and a single CoolTech fan. According to ASUS, the DirectCU Mini is up to 20% cooler and slightly quieter than previous GTX 670 cards despite the smaller form factor.
This new card will be a great addition to Mini-ITX-based systems where saving space anyway possible is key. It is nice to know that gamers will soon have the option of powering a small form factor LAN box with a GPU as fast as the GTX 670. Even better, water cooling enthusiasts will be happy to know that the card still uses a reference PCB, meaning it is compatible with existing water blocks made for the current crop of GTX 670 cards.
Pricing and availability have not been announced, but the small form factor-friendly GPU is now official and should be coming sometime soon.
Subject: Motherboards | March 8, 2013 - 06:30 AM | Tim Verry
Tagged: roundup, motherboards, mini-itx, celeron 847, APU, amd e-450
While high end motherboards and processors tend to get the most attention from enthusiasts, sometimes less is better (*waits for Josh to stop laughing on the podcast). More often than not seen integrated in small form factor OEM boxes, there are a few motherboards out there that come as a bare board and integrated processor to be the basis of low power desktops, network devices, and home theater PCs. Both Intel and AMD have hats in the low power game, and Hartware.de has pitched four such low power boards against each other. The MSI C847MS-E33-847 and Biostar NM70I pack Intel Celeron 847 CPUs, The Zotac D2550-ITX WIFI hosts an Intel Atom D2550 processor plus a NVIDIA GT 610 IGP, and the ASUS E45MI-M Pro is powered by an AMD E-450 APU.
Hartware.de puts several low power boards into the thunderdome to see which one(s) reign supreme.
As it turns out, the results are nearly in line with what one might expect. The Atom D2550-powered system was the slowest, the APU and ASUS motherboard was the fastest, and the Celeron was somewhere in the middle. The AMD E-450 APU used the most power, and the system was one of the most expensive, however. Interestingly, the Atom system was not all that much more power efficient than the Celeron despite the lower performance and weaker hardware. The Celeron 847 chip had decent CPU performance, and mid-range power and some of the best thermals. All of the configurations were able to playback media, but the AMD system gave the most fluid results.
If you are in the market for low power system parts, the review is worth checking out.
Here are some additional Motherboard reviews from around the web:
- GIGABYTE Z77N-WiFi Mini-ITX @ TweakTown
- ASRock Z77 Pro4-M LGA 1155 @ HardOCP
- Gigabyte GA-F2A85X-UP4 FM2 @ PC Perspective
- ASRock's Z77E-ITX Mini ITX @ The Tech Repot
- ASUS Sabertooth 990FX R2.0 @ OCaholic
I'm pleasantly surprised at all the Mini-ITX motherboards being made lately.
Subject: Cases and Cooling | February 17, 2013 - 03:51 PM | Ryan Shrout
Tagged: ncase, mini-itx, mini ITX, m1
We love us some mini-ITX products that enable us to build powerful PCs and HTPCs in smaller chassis and using smaller footprints than traditional ATX and even MicroATX designs. We have reviewed several mini-ITX motherboards including EVGA's Z77 Stinger and even a couple of mini-ITX based pre-build computers like AVADirect Mini Gaming PC and the Digital Storm Bolt. All of these products showcase the capability to get incredible computing and gaming horsepower in a small design.
Recently I came across a thread in the /r/hardware sub-reddit discussing crowd funding for a new kind of mini-ITX chassis design. In what started as a discussion on the HardForum has resulted in a design ready for prototyping and tooling.
That is where the community comes in! The designers have started an Indiegogo.com project to help get funding from users like you and me to enable prototype units to be built and tested. I already tossed in a chunk of money from PC Perspective and I think once you see what they have designed you'll be interested as well.
The NCASE M1 is a new Mini-ITX case that raises the bar in performance, versatility, and design for SFF PC cases. With support for 12.5” GPUs, water or air cooling, and a variety of drive mounting options, the M1 offers unparalleled power and flexibility for its surprisingly small footprint, all wrapped in an elegant, minimalist aluminum exterior.
We've spent months perfecting the design using feedback from [H]ardForum community and Lian Li's engineers. Our goal is to take this design to production, and we need your help.
The next step before production is to test a prototype of the M1. The funding goal is the minimum we need to produce a prototype plus a small components budget to test fitment, thermals and noise.
The more funding we're able to raise, the more hardware configurations we'll be able to test for, which leads to a better product. If we achieve our funding goal, don't let it stop you from backing us! Every little bit will help make the M1 better.
Just look at the projected specifications and device support:
Dimensions: 240mm x 160mm x 328mm (250mm tall w/feet), 12.6L
Motherboard Support: Mini-ITX, Mini-DTX
Expansion Slots: 3
GPU Support: 12.5” (slot 1 & 2) or 11” (slot 3)
CPU Cooler Support: Up to 105mm tall; 120mm and 240mm radiators also supported
Drive Support: 3 x 3.5” HDD mounts; 3 x 2.5” drive mounts; 1 x slim slot-load optical drive mount
Power Supply Support: SFX or ATX (up to 140mm non-modular, or longer w/short GPU)
Fan Support: 2 x 120mm side & bottom mounts; 80/92mm bottom & rear mounts
Front Ports: 2 x USB 3.0, headphone and microphone
A chassis design that is built not just but a single engineer in Taiwan but rather by actual users that want to perfect a product based on the input from the community DIRECTLY - it is an incredible goal!
I have included some additional images below but you should make sure you head over to the Indigogo.com project page and learn about the NCASE M1 and contribute any amount you can to make this a reality. Hopefully, in the not-too-distant future we'll be able to pick up one for ourselves and showcase it on PC Perspective!
Subject: Motherboards | February 5, 2013 - 06:00 PM | Jeremy Hellstrom
Tagged: asus, Intel Z77, P8Z77-I Deluxe, mini-itx, lucid
The most instantly noticeable thing about the ASUS P8Z77-I Deluxe has to be the riser card sporting an array of capacitors and providing 8+2 power phase VRMs. What isn't as noticeable until you use the motherboard is the Intel SRT support, Lucid Virtu and the overclocking options available in the UEFI BIOS. Being a Mini-ITX board, the singly PCI Express x16 slot and dual memory slots are to be expected but the spacing is such that you should have no problems with full sized DIMMs or oversized GPUs, depending on the cooler and case you choose. The included dual Wi-Fi antennas are a nice bonus from ASUS as well. Drop by The Tech Report to see this board in action.
"The P8Z77-I Deluxe packs a lot of goodness into a tiny package. We take a closer look at the board's features, performance, and overclocking potential."
Here are some more Motherboard articles from around the web:
- ECS NM70-I2 (V1.0) Mini-ITX Motherboard Review @ Madshrimps
- GIGABYTE Z77X-UD4H LGA1155 Motherboard Review @ Hardware Canucks
- Gigabyte Force M7 Thor @ LanOC Reviews
- ASRock Z77 OC Formula Motherboard Review @ Madshrimps
- ECS Z77H2-A2X (v1.0) Review: "Golden" LGA 1155 Mainboard from the "Black" Series @ X-bit Labs
- MSI Z77 MPOWER Review: OC Certified LGA 1155 Mainboard from the Big Bang Series @ X-bit Labs
- Gigabyte Z77X-UP7 @ eTeknix
- ASRock Z77 Extreme3 @ X-bit Labs
- MSI Z77 MPower Review: The XPower’s Little Brother @ AnandTech
- BIOS Option Of The Week - DRAM Act to PreChrg CMD @ TechARP
- ASRock FM2A85X Extreme6 for AMD Socket FM2 APUs @ techPowerUp
- Gigabyte GA-F2A85X-UP4 @ X-bit Labs
- BIOSTAR Hi-Fi A85W Motherboard Review @ Legit Reviews