EVGA Brings Custom GTX 780 Ti Early
Reference cards for new graphics card releases are very important for a number of reasons. Most importantly, these are the cards presented to the media and reviewers that judge the value and performance of these cards out of the gate. These various articles are generally used by readers and enthusiasts to make purchasing decisions, and if first impressions are not good, it can spell trouble. Also, reference cards tend to be the first cards sold in the market (see the recent Radeon R9 290/290X launch) and early adopters get the same technology in their hands; again the impressions reference cards leave will live in forums for eternity.
All that being said, retail cards are where partners can differentiate and keep the various GPUs relevant for some time to come. EVGA is probably the most well known NVIDIA partner and is clearly their biggest outlet for sales. The ACX cooler is one we saw popularized with the first GTX 700-series cards and the company has quickly adopted it to the GTX 780 Ti, released by NVIDIA just last week.
I would normally have a full review for you as soon as we could but thanks to a couple of upcoming trips that will keep me away from the GPU test bed, that will take a little while longer. However, I thought a quick preview was in order to show off the specifications and performance of the EVGA GTX 780 Ti ACX.
As expected, the EVGA ACX design of the GTX 780 Ti is overclocked. While the reference card runs at a base clock of 875 MHz and a typical boost clock of 928 MHz, this retail model has a base clock of 1006 MHz and a boost clock of 1072 MHz. This means that all 2,880 CUDA cores are going to run somewhere around 15% faster on the EVGA ACX model than the reference GTX 780 Ti SKUs.
We should note that though the cooler is custom built by EVGA, the PCB design of this GTX 780 Ti card remains the same as the reference models.
Subject: Mobile | September 18, 2013 - 12:04 PM | Ryan Shrout
Tagged: tegra note, tegra 4, tegra, tablet, pny, nvidia, evga
Over the past couple of months there have been several leaks about a potential NVIDIA-branded tablet based on the Tegra 4 SoC. Most speculated that NVIDIA had decided to enter into the hardware market directly with a "Tegra Tab" in a similar vein to the release of NVIDIA SHIELD. As it turns out though NVIDIA has created a platform for which other companies can rebrand and resell an Android tablet.
According to NVIDIA, the Tegra Note platform will enable partners to bring 7-in tablets to market packed with the feature set NVIDIA has been promising since the launch of the Tegra 4 SoC. Those include stylus support, high quality audio, HDR camera capabilities and 100% native Android operating systems.
Maybe more interesting are the partners that NVIDIA is teaming with for this launch. While companies like ASUS have already done the development work to prepare various size tablets based on Tegra chips in the past, NVIDIA is going to introduce a couple of its graphics cards partners to the mobility ecosystem: EVGA and PNY in North America.
While we have questions about the capability for either of these companies to truly support a tabletin today's market but the truth is likely that NVIDIA is handling most if not all of the logistics on this project. What is not in question is the potential for high value: these tablets will start with a suggested retail price of $199.
We already know most of the technical details about the Tegra 4 SoC including the 4+1 Cortex A15 CPU cores and the 72-core GPU. NVIDIA claims they will get 10 hours of video playback with this platform but I would like to get data on the weight and battery size before calling that a win. The display resolution is a bit lower than other competing high-end options in the market today but the sub-$200 price point does mean there had to be some corners cut.
UPDATE: I asked NVIDIA for more information on the size, weight and battery capacity and got a quick answer. The battery capacity is 4100 mAh and the entire device weighs 320g. Compared to the Google Nexus 7, the current strongest 7-in tablet in my opinion, that is a 4% larger battery (vs 3950 mAh) and 10% heavier device (vs 290g). The Tegra Note reference is also a bit thicker at 9.6mm compared to the 8.65mm of the Nexus 7.
There are more details on the official NVIDIA blog post making the announcement this morning including direct OTA Android updates so check that out if you think you might be interested in one of these tablets in the coming months!
Subject: Cases and Cooling | September 13, 2013 - 01:44 PM | Tim Verry
Tagged: mini ITX, hadron air, hadron, evga
EVGA has launched a new barebones Mini ITX case called the Hadron Air. The new case is in the same vein as the MiniBox chassis it showed off at Computex earlier this year. The new Hadron Air measures 12" x 6.6" x 12.1" (HxWxD) and is constructed of aluminum with a black brushed finish on the outside.
The Hadron Air has curved edges and rounded corners. The front of the case is lifted up slightly by case feet, putting the case at a slight angle. There are vents on the top and right side of the case as well as an acrylic window on the left side panel. A bay for a slim slot loading optical drive and the front IO port are located on the right side of the case. The front IO includes two USB 3.0 ports and two HD audio jacks. The back of the case has a bottom mounted power supply, two PCI slots, and two water cooling passthrough grommets.
EVGA is bundling the case with a small form factor 500W power supply. The PSU is 80 PLUS Gold rated and offers up 40A on the 12V rail. The case supports Mini ITX motherboards, two 2.5" or 3.5" storage drives, and dual slot graphics cards up to 267mm in length. As far as cooling, the case supports two 120mm exhaust fans in the top panel and the power supply has its own small intake fan. A list of compatible CPU coolers can be found here.
The case comes bundled with a 500W power supply, manual, AC power cord, two SATA cables, and a bracket for a slim slot loading optical drive.
The Hadron Air is available now for $189.99. The Mini ITX chassis is part of the Hadron series of cases which includes the Air and a water cooling optimized version called the Hadron Hydro which is reportedly "coming soon."
More information on the Hadron Air can be found on this EVGA product page.
Subject: Graphics Cards | August 14, 2013 - 06:03 PM | Ryan Shrout
Tagged: sweepstakes, sli, nvidia, giveaway, evga, contest
UPDATE: Winners have been selected and contacted - if you weren't one of the five winners check back for more contests and giveaways!! Thanks for listening!!
While at Quakecon this year EVGA showed off its new collection of Pro SLI Bridges that add a bit of sexy to any NVIDIA multi-GPU system. These are much more than just the standard SLI bridge that you know of today: they are sleek, have a brushed metal finish and if you have GTX 700-series or TITAN graphics card, they light up as well!
Because EVGA is a big supporter of PC Perpsective, they are sending over a handful of the 3-Way Pro SLI Bridges (that can also be used in 2-Way configurations) to give away to our readers.
How can you win one of the five free units that EVGA sent us?
- Fill out the form below with the requested information.
Listen to this week's (Episode #264) PC Perspective Podcast (live or after the fact) and I'll give you the code word to include in the form below.
- You can download or watch the podcast right here: http://pcper.com/podcast
That's it!! You can win anywhere in the world and our winners will be randomly picked from the submissions we receive no later than the 20th of August at 6pm ET.
A big thanks goes to EVGA for providing these units!!
Subject: General Tech, Cases and Cooling | July 12, 2013 - 04:13 AM | Tim Verry
Tagged: PSU, Intel, haswell, evga, c7, c6, 80 Plus Bronze
EVGA recently launched a new 500W power supply called the 500B. The new ATX PSU is haswell ready and supports the advanced low-wattage C6 and C7 sleep states. The 500B, as the name suggests, is a 500W unit rated 80 PLUS Bronze for 85% efficiency under typical workloads.
Although it is not modular, it has several other enthusiast friendly features. It supports 40 Amps on the single +12V rail and has over-current and over-voltage protection. Further, it has two 6+2-pin PCI-E power connectors, a single 8-pin CPU power, and a 24-pin ATX connector along with a couple molex and SATA power for good measure. Also, the PSU fan automatically adjusts speed for low noise.
The EVGA 500B (model number 100-BR-0500-KR) comes with a 3 year warranty. Pricing and availability have not been announced. It looks to be a decent option for budget builds, and should be priced competitively. More information and additional photos can be found on this EVGA product page.
EVGA has announced a new flagship LGA 2011 motherboard called the X79 Dark. The new motherboard is E-ATX and measures 304.8 x 263.5mm. It features a 12 layer PCB, new UEFI BIOS, and a number of enthusiast and overclocking-friendly features.
The motherboard features a 12+2 VRM for the CPU, and a 4 phase VRM for the memory. The board has a single LGA 2011 processor socket surrounded by four DDR3 DIMM slots on either side and a large hexagonal heatsink for the VRM above it. Below the CPU socket, EVGA has included five PCI-E 3.0 x16 slots and a single PCI-E 3.0 x4 slot. All of the physical PCI-E 3.0 x16 slots are at least electrically x8, and two of them are electrically x16. The bottom-right corner of the motherboard is taken up by a massive PCH heatsink with a large red EVGA logo. To the right of the PCH heatsink, the board has 10 SATA ports at right angles to the board PCB. Six of the SATA ports are SATA III 6Gbps and four of them are SATA II 3Gbps.
Of course, the board has Intel Ethernet controllers, 8 channel audio, and internal headers for two additional USB 3.0 ports. The board requires one 24-pin, two 8-pin, and one 6-pin PCI-E power connectors to supply power to the board and connected components. Finally, EVGA has also included EVBot voltage measurement points along with an updated UEFI BIOS.
The EVGA X79 Dark has a fairly extensive external IO panel, which includes:
- 6 x USB 2.0
- 1 x Bluetooth
- 4 x USB 3.0
- 2 x eSATA 3Gbps
- 5 x Analog audio jacks
- 1 x S/PDIF
- 2 x Gigabit Ethernet ports (Intel NICs)
The new LGA 2011 X79 Dark motherboard is model number 150-SE-E789-KR and will be available soon for $399.99.
Getting even more life from GK104
Have you guys heard about this new GPU from NVIDIA? It’s called GK104 and it turns out that the damn thing is found yet another graphics card this year – the new GeForce GTX 760. Yup, you read that right, what NVIDIA is saying is the last update to the GeForce lineup through Fall 2013 is going to be based on the same GK104 design that we have previously discussed in reviews of the GTX 680, GTX 670, GTX 660 Ti, GTX 690 and more recently, the GTX 770. This isn’t a bad thing though! GK104 has done a fantastic job in every field and market segment that NVIDIA has tossed it into with solid performance and even better performance per watt than the competition. It does mean however that talking up the architecture is kind of mind numbing at this point…
If you are curious about the Kepler graphics architecture and the GK104 in particular, I’m not going to stop you from going back and reading over my initial review of the GTX 680 from January of 2012. The new GTX 760 takes the same GPU, adds a new and improved version of GPU Boost (the same we saw in the GTX 770) and lowers down the specifications a bit to enable NVIDIA to hit a new price point. The GTX 760 will be replacing the GTX 660 Ti – that card will be falling into the ether but the GTX 660 will remain, as will everything below it including the GTX 650 Ti Boost, 650 Ti and plain old 650. The GTX 670 went the way of the dodo with the release of the GTX 770.
Even though the GTX 690 isn't on this list, NVIDIA says it isn't EOL
As for the GeForce GTX 760 it will ship with 1152 CUDA cores running at a base clock of 980 MHz and a typical boost clock of 1033 MHz. The memory speed remains at 6.0 GHz on a 256-bit memory bus and you can expect to find both 2GB and 4GB frame buffer options from retail partners upon launch. The 1152 CUDA cores are broken up over 6 SMX units and that means you’ll see some parts with 3 GPCs and others with 4 – NVIDIA claims any performance delta between them will be negligible.
Subject: Cases and Cooling | June 19, 2013 - 04:33 PM | Tim Verry
Tagged: haswell, c6, c7, power supply, evga
Intel’s latest Fourth Generation Core “Haswell” processors are now official, and additional power supply manufacturers have since stepped up to provide their own Haswell PSU compatibility lists. EVGA is the latest PSU vendor to do so, announcing that all of tits SuperNOVA branded units are fully compatible with the new CPUs and new C6 and C7 sleep states.
The following EVGA power supplies are compatible with Haswell and the lowest power (0.05A) sleep states:
- EVGA SuperNOVA NEX 1500 Classified (120-PG-1500-XR/VR)
- EVGA SuperNOVA NEX750G Gold (120-PG-0750-GR)
- EVGA SuperNOVA NEX750B Bronze (120-PB-0750-KR)
- EVGA SuperNOVA NEX650G Gold (120-PG-0650-GR)
- EVGA SuperNOVA 1300 G2 (120-G2-1300-XR)
- EVGA SuperNOVA 1000 G2 (120-G2-1000-XR)
The list of compatible units spans across the range of SuperNOVA PSUs, from 650W to the monstrous 1500W model.
For a refresher on Haswell’s new C6 and C7 sleep states, check out our previous coverage of the issue as well as coverage of compatible PSUs from other vendors.
Subject: Cases and Cooling | June 6, 2013 - 10:31 AM | Tim Verry
Tagged: evga, minibox, mini-itx, gtx titan, gk110, gaming, computex, computex 2013
First shown off at CES 2013, the EVGA Minibox is a small form factor chassis for Mini-ITX systems that can accommodate large graphics cards. EVGA has managed to enable users to pack a lot of hardware into this tiny form factor chassis. As a demonstration of the case's capabilities, the company showed off the latest version using a full system build with Core i7-4770K and GTX TITAN interals at Computex this week in Taipei.
The Minibox chassis itself is a dark brushed metal case with two USB 3.0 ports on the front IO and space for a slot loading optical drive. The MiniBox chassis further features a motherboard tray that supports Mini-ITX boards, two 2.5" SATA hard drive bays – and best of all – enough room to install full size GPUs. In order to support lengthy graphics cards, EVGA is including a small form factor 500W power supply that is mounted on the floor of the case..
HEXUS reporters spot the EVGA Minibox at Computex 2013. Look how small it is!
There will be at least two SKUs of the Minibox, depending on whether you want to go with air or water cooling. According to Bit-Tech.net, the air cooled version will use two 92mm fans in the top of the case and one 80mm fan for the bottom-mounted PSU. The water cooled SKU will be slightly larger but have enough room for a water cooling radiator (likely 240mm). Beyond that, details are scarce, but the air cooled version is said to be available as soon as next month with water cooled options becoming available later this year.
The Minibox looks to be one of the better Mini-ITX cases out there (although the price is still unknown), and should be popular among enthusiasts wanting a small box that does not sacrifice gaming potential.
Subject: General Tech | June 1, 2013 - 08:58 PM | Tim Verry
Tagged: gtx 770, evga, acx
Now that NVIDIA's GTX 770 reference graphics card is official, the various partners have begun unleashing their own spins on the hardware. Unlike the TITAN, NVIDIA is allowing custom PCBs and coolers, making the selection of GTX 770 cards much more diverse and unique.
In fact, EVGA has a slew of GTX 770-based graphics cards planned for 2014. Out of the gate, there will be two graphics cards available to consumers: The GTX 770 and the GTX 770 Superclocked. Both cards will come equipped with the company's new ACX cooler. In addition, the GTX 770 FTW, GTX 770 4GB, GTX 770 FTW 4GB, and the GTX 770 Classified 4GB cards will also come with the ACX cooler and will be available later this year. Details on those last four cards are still unknown, but EVGA has provided specifications on the first two, which will be available soon.
The EVGA GTX 770 w/ ACX
The EVGA GTX 770 w/ ACX is a GK-104 “Kepler” GPU clocked at 1046 MHz base and 1085 MHz boost. The card also features 2GB of GDDR5 memory clocked at 7010 MHz.
EVGA is also introducing a Superclocked edition of the GTX 770 that will use the new ACX cooler. This GTX 770 ACX Superclocked has factory overclocked speeds of 1111 MHz base and 1163 MHz boost. The 2GB of GDDR5 memory remains at the reference clockspeed of 7010 MHz.
Both of these cards use EVGA's new ACX cooler which uses a new heatsink design paired with two fans (dual ball bearing) and a back-plate that is reportedly lighter, quieter, and cooler-running than the reference cooler.
The EVGA GTX 770 4GB Classified GPU with ACX cooler. It is listed on the site, but not available yet.
The EVGA GTX 770 ACX and GTX 770 Superclocked ACX will be available soon for an as-yet-unannounced price. The Superclocked edition has some impressive factory overclock numbers, though it will likely come at a premium. The other interesting takeaway from the EVGA announcement is the confirmation of 4GB GTX 770 cards coming in the future. More information can be found on the EVGA product page.
Get notified when we go live!